Time to sort out my series 2 ! #lambretta #kickbackgarage
Пікірлер: 17
@stuhollyhead42943 жыл бұрын
Im trying my 1st lambretta so have become addicted to ur videos hehe very good 👌
@ianmcgarrigle95103 жыл бұрын
hi there i am just at this job now but as the parts were going to be renewed i cheat . first i flipped the frame upside down and mig weld a small bit of flat bar across the inside of the bearing seat , that gives you something to drift against and the heat from welding seems to help , i also do this with trashed roller bearings that have fallen to bits to remove the outer shell .. :)
@tavspeed11014 жыл бұрын
merry xmas kickback,always enjoy your videos,good humour and a whisky drinker to boot,keep em coming for 2020,all the best from yorkshire
@exsoulagent4 жыл бұрын
Merry Christmas Rob & Seb Been through the fork bearing race and it was a right pig, bought two sets of bearings as I fit them in loose, better feedback I think. I did laugh at the where has my tools gone moment as I do that quite on a regular basis. I’ve also started planning my euro trip too coincide with the Norway Rally so I’ll be needing a few more details soon 😉
@kickbackgarage4 жыл бұрын
Haha, spend more time looking for tools than using them 😀 here is the link to the rally. I think you have to use Google translate or just ask me. www.roughnecks.no/ my email is www dot lambretta at online dot no. 😎
@shaundewar73974 жыл бұрын
Rob, would love to see the Vape ignition installed. Bought the same a few months ago for a planned engine rebuild and had a quick look at the instructions. Though the kit is for a Lambretta the instructions show a Vespa and the instructions on line are exactly the same as the printed one in the box. Theres only one other vid I can find showing the Vape installation but importantly it doesn't show the wiring up. Have a great Xmas and looking forward to seeing more Kickback Garage in 2020.
@kickbackgarage4 жыл бұрын
Ok. I'll see if I can make a propper instalation guide as soon as the scooter is back together.
@TheSteelweasel4 жыл бұрын
merry xmas bro
@TheSteelweasel4 жыл бұрын
rob no no no the fork has two small holes to use a pin punch to knock the bottom race up and off .
@kickbackgarage4 жыл бұрын
I actualy didn`t know that! cool. Motorbike and pushbike manufacturers should take note!
@TheSteelweasel4 жыл бұрын
see you have the vape rob , mines been very reliable so far mate .
@kickbackgarage4 жыл бұрын
Yeah, should be good. Had to machine down the flywheel to fit the casa case but it it on my little myford.
@daviddekruif86313 жыл бұрын
I'm doing a complete restore dry fitting everything to the point its tuned, tweeked, and rideable then taking everything apart for painting and powdercoating. Are the bottom and top new races ok to be removed again and reinstalled after powdercoating or am I going to have to get another set?
@kickbackgarage3 жыл бұрын
It depends on how they look. My take on the matter is that its quite a big job to have to take them out again in a year's time. I fit new ones for piece of mind.
@daviddekruif86313 жыл бұрын
@@kickbackgarage Thank you very helpful. Cheers!
@TheSteelweasel4 жыл бұрын
i made a tool for knocking out the bearing races , might show it you in one of my vids sometime bro .
@kickbackgarage4 жыл бұрын
I have a spring bar at work that would do a good job of it but luckily not a job I do that often these days. These have sat on the scoot since 1960 and painted in which didnt help matters much. Proberbly the hardest ones to remove iv`e done. The series one was a doddle!