In this video we show our latest product for the Land Rover Discovery 3 and Discovery 4 ( LR3 / LR4 ) This is available to purchase on our website :- www.powerfuluk.com/search?q=l...
Пікірлер: 31
@supercrazysane6 ай бұрын
Fantastic - ready for some Tokyo Drift action 😎👍
@mvirdi23336 ай бұрын
Also the lights look 👀 very cool with changing colours.
@L6635 ай бұрын
We used this car for my daughters prom a few years ago - this is when we added the lights !
@alikani1st5 ай бұрын
Loved the voice effects 😂👌
@jimmyquinn96396 ай бұрын
Lovely job Simon 👍👍👍👏👏⭐️⭐️⭐️⭐️
@L6635 ай бұрын
Thanks Jimmy
@Rickwardful6 ай бұрын
Is there a reversing camera on some of the D4 HSE’s? Fairly certain the ones on the L320 RR Sport are in its spoiler. If the same on a L319 Disco, what refitting would be required?
@roberttruman83326 ай бұрын
Third? I have a Discovery 3 now and am in battle with the EPB, so far 5 hours in and only managed to remove 7 of the 8 screws holding the cover on 😅
@L6635 ай бұрын
There is a reason the G4 is stuck in the workshop..... the EPB....
@roberttruman83325 ай бұрын
When I fix it I’ll let you know the high lights 😀
@fearnsey88003 күн бұрын
I have the original one on my Disco 3 but half of the leds are out do you sell a replacement light fitting for it ? I think its called the HST kit and was factory fitted
@landroverSV5 ай бұрын
Nice, but I already put the original OEM spoiler on mine. Nice kit! Keep the Disco 3 young looking 👌 Anything else you may have down the road for the Disc 3?
@L6635 ай бұрын
We need to do the rear brake pipe video next.... we are going to use compression joints !
@landroverSV5 ай бұрын
@L663 will you ever offer the six piston breaks for the Disco 3 again?
@dellstewart8470Күн бұрын
Hey Simon I’m just fitted the spoiler to my D4 My question is, why drill into the brake light? I’m using the cavity where the old rear washer jet was for the new washer pipe and the wiring for the brake light. Plus I’ve attached additional cable lengths to the new washer pipe and rear brake light so I can start to thread them through before applying the bondo and all the faff of threading them through after. Just some thoughts and tips on my install
@simonjeffersonКүн бұрын
Yes someone else has commented in the comments that they did this - seems a better plan ! Simon
@sergeifil69906 ай бұрын
1. It is possible to make a screw in the middle 2. You must immediately provide a place for the camera. 3. No need to make a hole in the lantern. You can make the hole for the tube larger.
@L6635 ай бұрын
Good points - I like the idea of the larger washer hole for the brake light wire.
@HQBProductions6 ай бұрын
Hello Simon…Good work on this as it looks neat even if it takes a bit of fiddling to get it all together. Re the possibility of the centre part catching the roof, could you modify the moulding so that it curves in slightly from the edge for say 20 cm by 2-3 mm? That might be a problem now after you have set it all up but I wonder if some tailgates might be set slightly different and not have just enough clearance? If I had a D4 I would buy it! If I had a defender I would as well! 😃😃😃Richard.
@L6635 ай бұрын
Evening Richard - as you can see we have been busy since getting back... the spoiler was a tricky design with the washer and brake light etc but we are pleased with the final result even if it is a bit of a fiddle to fit.
@lesgreen48246 ай бұрын
Hi, sorry to be a keyboard warrior but we didnt get the finished full on side view so I assume it looks great. Also does it whistle when on the motorway at 70mph?
@L6635 ай бұрын
Ben has done some nice pics on the website.
@landroverSV5 ай бұрын
The original is much better! Do you offer the six pot front breaks any longer 🤔 for the D3?
@Ali-or1gh6 ай бұрын
Simon when will you have Part number: RRV763-Blk back in stock. Frustrating....
@L6635 ай бұрын
We have had a lot of quality issues with the tape on these - they are for sale on ebay 4x4clearance shop - this is our outlet shop
@mvirdi23336 ай бұрын
Hi . Very nice but I am still awaiting Rear Tailgate LED Lightbar for Range Rover L405. ❤❤👍👍🙏🙏🇬🇧
@L6635 ай бұрын
We need to look at this again !
@ianscorey52936 ай бұрын
Hi Simon……. Gr8 to have you back!!! Interesting video….. even if in some parts it got close to soft porn???? Regards Ian 👨🎤🇳🇿👍👌😂😂
@ecossearthur6 ай бұрын
Boom Boom!! 💥 💥 Taco Tuesday!
@campingbegins6 ай бұрын
That's the ugliest thing I've ever seen on a Disco. Nothing like the OG spoiler. Enjoy pulling that made in PRC tat off in 12 months and wishing you'd not drilled a hole in the high level brake light. 🤠
@L6635 ай бұрын
Each to his own....we were trying to design something a little different to OG spoiler....the brake light needs replacing anyway - its faded and cracked. This was designed in house but yes it was made in China as UK costs were too high !