Great tip, I had a new Cub Cadet recently that a customer said the belt was slipping, come to find out the belt was never put on the pully from the factory and the belt was riding on the hub of the pully. I was fortunate that the tractor was new and the pulley just came down easily. Thanks for a great video.
@IndRepair6 ай бұрын
That's an interesting one! Thanks for watching!
@philliphall51986 ай бұрын
My sister just bought a new mower and bought it straight to me to remove clutch and antizee it good She’s a smart lady 😊😊😊
@IndRepair6 ай бұрын
For sure!
@The942083 ай бұрын
You made me save a lot of trouble, thank you.
@IndRepair3 ай бұрын
Glad to help! Thanks for watching!
@philliphall51986 ай бұрын
It beats spending a hour trying to get pulley off and buying a new pulley 😊 As always Thank You
@IndRepair6 ай бұрын
It sure does! Thanks for watching
@dac70466 ай бұрын
Good practical advice- thanks.
@IndRepair6 ай бұрын
Appreciate that!
@Rein_Ciarfella6 ай бұрын
Good one, Martin! Nice to see a smile on your face at the intro. 😁
@IndRepair6 ай бұрын
Thanks! Funny part is I always smile but am not comfortable behind a camera so get weird looks on my face lol one day maybe
@garysgarage36696 ай бұрын
Great tip! some people are just cheap and some people are really struggling in today economy.
@IndRepair6 ай бұрын
I agree for sure!
@robcole3326 ай бұрын
Lol. He’s got his money’s worth out of that. What a great way to do with a stuck pulley. Thanks
@IndRepair6 ай бұрын
Haha I would say she got a little more than usual out of that one
@georgepruitt6376 ай бұрын
You might wish to add some "never-seize" to the engine bolts now. To save future headaches.
@IndRepair6 ай бұрын
I usually use it on shafts and PTO bolt but never have an issue with them seizing on engine mounting bolts never hurts though
@JP675216 ай бұрын
great tip
@IndRepair6 ай бұрын
Thanks for watching!
@bluegrallis6 ай бұрын
I had a pulley that needed to come off. The center of the V in the pulley was a full belt width off of lining up with the hydraulic units. I first drilled a 3/32 hole thru the side of the hub, in line with the keyway and sprayed 'blaster' in the hole. It all ran out the bottom so I used some plumbers putty to keep it in, letting it soak over night. Still no movement , even with some heat on the pulley hub. I then drilled to 5/16 holes in the flat of the pulley, far enough out from the hub to get a 5/16 bolt head to clear the hub. Put my home made puller plate on the bottom of the shaft and bolted it to the hub thru the holes I drilled. It did finally move with a bit more heat, by cranking on the puller screw. Evidently, the wrong pulley was put on this mower from day one, since the edge of the drive belt was always shredded after minimal run time. I now have a pulley that lines up with the hydro units and the E clutch bolts in at the proper position.
What rider was or is the easiest to maintain and work on....thanks....
@IndRepair6 ай бұрын
I prefer and recommend Simplicity mowers
@JeremyAnthony-w2r6 ай бұрын
Where are you from or located?
@IndRepair6 ай бұрын
Bloomington, il www.individualizedrepair.com/directions
@georgestrickland92786 ай бұрын
that's exactly what i thought you were going to do,me i almost always destroy the stuck pto
@IndRepair6 ай бұрын
I hear that for sure
@joehead12946 ай бұрын
Looks like you unhooked some steering linkage, too.
@IndRepair6 ай бұрын
Haha, yes I sure did. Strictly for the shot though
@miltonross22766 ай бұрын
Nice!
@IndRepair6 ай бұрын
Thanks for watching!
@robertmcmahon27446 ай бұрын
Thanks!
@IndRepair6 ай бұрын
Thank you
@michaelfarris25566 ай бұрын
Nice move on that one bet it saved a shit load of time.
@IndRepair6 ай бұрын
It seems like I forgot about this trick once upon a time and was prying and ruined the pulley then when I replaced it I was wondering why the heck I didn't just do it this way to begin with
@crisprtalk69636 ай бұрын
Rumor has it Einstein watched this video with amazement and jealousy of this genius trick.
@IndRepair6 ай бұрын
Had me and the wife rolling. Thanks for watching!
@matthewwearsch2426 ай бұрын
Great tip until you break a motor mount bolt off in the block
@IndRepair6 ай бұрын
I have seen exactly 0 break off when removing them on a riding mower. Push mowers I have seen it many times. Not sure why though
@matthewwearsch2426 ай бұрын
@@IndRepair good to know I've done it myself doing engine swaps on push mowers
@IndRepair6 ай бұрын
Yeah didn't really think at all about it until you said something thanks for watching!
@robertmcmahon27446 ай бұрын
Yet another great video. Straight and to the point. I've never had to deal with this situation, YET!! It's good to have this in my "book of knowledge" 📚🔧🔩when I do. As in the past when I've learn something from you, I again am sending a few bucks $$ your way to show appreciation and thanks.🤝(Sending it via the "Thanks" botton KZbin provides above. Hope others will do the same. Peace out and God Bless.😎✌🖖🤘🙏