Led Tv panel Vgh,Vgl short removal method by modifying gate signals on 40 inch TCL |AUO 39|T390HVN04

[@akshayvvasudev]

I did this just now… 100% successfull

[@priosiswanto9497]

Good job... I'm indonesian...thanks

[@atifservicecenter]

Can you explain, why did you used AVDD supply on LC1 point ?? It’s a fluctuating volts of VGH & VGL then why to use AVDD ?? Please answer

[@ElectroPixels]

Here you can use vgh also no problem, we removed the Voltages to lc1 and lc2 from the Levelshifter Ic before Bypassing, then bypassed the voltage to lc1. Its for removing vgh vgl shorting inside Glass Panel in lc1 and lc2

[@bakkrudeena270]

Super sir 100%successful THANK YOU

[@ElectroPixels]

Thank you sir Please Share the video Link and support us

[@prosahil7839]

God bless you sir many many thanks

[@IT_Electro_Automation]

Thank you so much for your guidance..It's working wonderful..

[@harjindersingh2818]

Thank🌹 sir ji

[@MdShuvo-pm4ez]

100% Right video

[@ItzSaswata]

Thank you very much sir

[@MdShuvo-pm4ez]

I did tha job 100% Right

[@ManiMani-xh7lo]

Thank you sir

[@rarelectronicstv]

Nice sir...

[@lawrencepatricio5776]

I have a 39" Panasonic TV with AUO panel. The panel board is very similar to yours. The display problem is freezing, double image and vertical lines. Thank you for your video. I will try this solution. As I understand, it's preferable to bypass LC1 or LC2 into AVDD instead of VGH to prolong the panel, correct? I'll try this temporary solution and update this comment if successful. Thank you very much!

[@ElectroPixels]

First you need to block the Voltages Entering to the LC1 and Lc2 from Levelshifter Ic, Then only Bypass the vgh or Avdd Voltage to lc1 first and check the picture, If picture is not ok then disconnect it from lc1 and connect to lc2 then check picture, If both Sides panel Gatesignals are complaint then its not Repairable

[@remijeradu5027]

@@ElectroPixels l👍🏻👍🏻👍🏻

[@djp2803]

Very good and the new

[@babuk1764]

Super sr tanku

[@ravikumargokulakrishnan3671]

Nice 👍👍

[@AjusVDO]

Where is your shop?

[@AjusVDO]

Please tell me where is your shop or whatsapp no.

[@omayemi2002]

Can you guilde me to repair mine ? It has similar fault i

[@SumitKumar-di2pf]

Sir ji mere pass same tv hai but usme koi voltage nhi bn rha hai

[@ElectroPixels]

Check Dc to Dc or any Shorting in Smd Capacitors

[@robbirobson7330]

Hello i have auo panel 43 inch i bypass lc1 lc2 now picture ok but after 1 minute 3 horizontal black lines appear. I tried tape blocking signal solution but no success. Tcon board is T420HVN06.3 Ctrl BD 42

[@ElectroPixels]

Which Voltage you bypassed in lc1

[@robbirobson7330]

@@ElectroPixels lc1 to vgh y lc2 to vgl

[@ElectroPixels]

Try instead of vgh use Avdd Voltage, then one by one check in lc1,and Lc2. If both sides are complaint then not Repairable

[@robbirobson7330]

@@ElectroPixels with avdd voltage i have double image and still black lines. only connection tovgh works. Left side panel has problem, i connected right side panel lc1 to vgh 30v and lc2 to vgl -9.8v. When tv is cold no lines. lines appear after 1 minute. If i connect lc1 and lc2 to left side, lines appear in lower half of tv. if i connect lc1 and lc2 in right side the lines appear in upper half of panel.

[@robbirobson7330]

@@ElectroPixels i connected one side lc1 and lc2 to vgh and vgl but the other side i connected to avdd and vgl. so after 5 minutes tv is normal and works all day. if one panel side lc1 and lc2 disconnected after 30 minutes i get flickering image and lot of horizontal lines. if both sides connected to avdd i get double image. if both side connected to vgh i immediately get horizontal bars after powering on and tv is unusable. so the only thing works is connect lc1 on one side to vgh and lc1 on other side to avdd. i think both sides are faulty normaly its no fix. i hope this helps to try if you have panel with both sides faulty, maybe it can still work

[@సత్యమేవజయతే-త7ల]

Good

[@technorajesh9684]

Sir please make video mi43 led tv panel problem all voltage ok but display vertical lines no picture problem

[@ElectroPixels]

Check for any Burning marks in both left and Right side Cof

[@daviderhahon]

Camera is moving too much. But we can understand your idea though.

[@ElectroPixels]

It's because of live Repairing, Using camera at one hand and Doing Repairing, Sorry For That Sir

[@princediwana0175]

Mere panal me avdd nahi aara h

[@ElectroPixels]

Check for Shorting In Any SMD capacitors. If You are not a Technician then contact Trained Panel Reparing Technician for Help

[@edtechph5444]

Watching ED TECH PH

[@ElectroPixels]

Thanks Friend

[@jimenezrockroke8473]

Alguien puede ayudarme ? Cómo traducir al español.... gracias.

[@princediwana0175]

Please help me

[@ElectroPixels]

contact nearest technician in your location .He can help you

[@nsdnsd4051]

Sir hindi me video banaye