Lenovo G50 not charging not coming on - motherboard repair Part2

UK Ebay store: www.ebay.co.uk...
US Ebay store: www.ebay.com/u...
WebSite: sorinelectroni...
Patreon support: / electronicsrepairschool
KZbin Members: / @electronicsrepairschool
Forum: forum.sorinele...
Discord: www.sorinelect...
My tools: www.amazon.co....
PayPal me: www.paypal.com...

[@sergeaudenaert]

You are so honest on the repairs Sorin even what they charge and what they cost - highly appreciated and respect your contributions to the community - take care

[@johnholmes1401]

I bought the same kit a month ago and would love to have some guidance and videos for me and the kids to follow along with. You sir are brilliant and treasured for the knowledge you freely distribute.

[@Lifeless11111]

I learned so much from you sorin ,I have repaired many motherboards , consoles ETC. please dont stop making videos, you are a great teacher for beginners but even me i learn stuff sometimes.

[@rogerwale4827]

Hi Sorin Even under the microscope these components are tiny, even the probes & tools look massive by comparison, it is any. wonder that occasionally mistakes are made. The honest thing to do was to leave it in. Thats why we love you....

[@LIONJCOMPUTERSOLUTIONS]

Thanks for everything sir I personally appreciate honestly because I have learnt many skills from you....I can now repair power pack and monitor even TVs you have been a savior to my life thanks a lot.

[@tinkmarshino]

Sorin I will be 70 in two years and I got that same idea last winter.. (I needed something to do in the winter time it is to cold to go outside in the shop..) But it is hard to do it myself.. It is hard for me to remember and I find that I can not stay motivated.. so this would be good for you to do this.. It might help me get to where I understand it enough to light a fire to help me get further.. I have arduinos, raspberry pies, esp32s and a few other things.. So I am ready.. If you want to do this on air..

[@KeithPotts]

Thank you to your videos they have gave me confidence to test and change stuff on the board and my laptop now works perfectly keep up the good work

[@reg2590]

For stripping small wires, try gripping the wire in the end of a small crocodile clip and pull! - found this tip on the web somewhere; works for me.

[@blagzster6255]

Definitely up for the Arduino vids. Like you, I'm a hardware guy and I'd love to learn the basics of that crazy strange software stuff.

[@jonsparano6937]

From one old Electronics hardware guy to another, Arduino is a blast! I just got a sensor kit from the same company through Amazon

[@MilekaRobot]

Finally, one hour+ video :D Works like a cure to me ;)

[@DanDoucet101]

Yes I'm interested in Arduino. I got this exact kit last year and have gone through some of the tutorials. I found Elegoo's kit to be quite good. Really enjoying your videos

[@azersamaali2016]

I'm not sure but ,if anyone else trying to find out consumer electronics repair try Saankramer Electronic Magazine System (should be on google have a look ) ? Ive heard some interesting things about it and my m8 got excellent results with it.

[@tachidatumoto6016]

@@azersamaali2016 who care.

[@ReparadorAficionado]

Back in the day I ordered a complete kit for Arduino called Tinker kit, from the UK to Mexico. It had all kinds of sensors and the electronic boards were top quality. I recommend you those.

[@kriswillems5661]

What's the function of the second mosfet you've bridged? Only current limiting? Why did it blow?

[@zyxnull]

YES SORIN!!!, Please do some videos on micro controllers, I've bought a LOT of this things and they are always fun to play with

[@catalinconstantinescu3888]

super tare ideea cu focus by arduino :)). Este buna chiar si pentru aparatele care au autofocus, fiinca pe intuneric sau pe seara daca vrei sa pui focusul pe ceva intunecat este posibil sa nu reuseasca ...exista excepti in functie de aparat dar oricum ideea este interesanta. Partea dificila dupa parerea mea ar fi sa iti dai seama unde din cadru a facut focusul, adica daca este o poza de portret caz in care umpli cadru cu o persoana atunci da te-ai putea folosi de senzorul ultrasonic sa iti spuna distanta pana la primul obiect... Problema apare cand vrei sa pui focusul la o alta adancime nu neaparat cel mai apropiat obiect, sar putea sa mearga daca poti avea un unghi foarte mic in care masoara senzorul asfel sa il poti orienta in diferite locuri din raza cadru

[@lucianmihai7895]

Apeciate you, onest genuane guy, grate brain, big passion and a lot of knowledge, an example for many, Keep going and thanks!

[@Dr.muthanna]

An interesting video in tracking a serial issues Thank you Sorin

[@donniedarko7891]

for this used stuff you have to be a master in repairing. i like your channel

[@asiqraja4904]

I love watching your videos and can learn. My country is Bangladesh. I am watching from Bangladesh

[@wayneharvett6170]

Please video the charge circuit repair. There is very little on the internet addressing charge circuit troubleshooting. Thanks. Your videos are great.

[@doatkormoa9533]

Man you're cool I like your video, very informative and detailed Im putting you on my adblock whitelist

[@nileshindulkar295]

Hello there, my lenovo G50-45 laptop is also facing same problem. I have reset Bios battery but still my laptop not coming on. Also I would like to tell you Soren that there is sparking happening when I try to insert laptop battery between terminals of battery & laptop. Power supply is all good. You should have shown clearly how to bridge MOSFET. This are corona pandemic times. Your videos are welcome, to those who have solved their problems by watching your video. Carry on great work. Kindly let me know video for bridging MOSFET & what tools are needed. Thanks a lot from India 🇮🇳. 🙏🙏🙏

[@1103-x5r]

Micro controller programming can be fun when it's in machine code and not in C, gives you a hardware level coding experience. I think you'll be surprised how many kits are available nowadays usually programmable in C. I2c Bus programming.

[@LaptopDisassembly]

I thought i was the only one, that have self-decomposing laptops that are coming for board repair. You fix one thing, and 3 more are falling apart.

[@NomNomNom1989]

Ive done many laptop repairs while I was studying electronic engineering and man I can say for sure that the whole laptop industry should be sued. How can they get away since years with planned obsolescence and no one says anything about it? cheap HDMI ports, cheap charging ports, bad soldering, capacitors flying around in the laptop, horrible cooling, thats everything which could be fixed really easily but they want the laptop to fall apart within 2 years.

[@petartomic9783]

And i think from my expirience in programing ,beacuse i didn't know how to program at all and i was really bad at it ,it is a way of thinking and remebering ,it's like when you get to start writing your head switches to programing thinking.

[@stevenpates3791]

I really like your videos, thank you for taking the time to do these because you really help people.

[@Snowbag1998]

40:30 I got my answer. Thank you Sorin !

[@loayabbas2454]

nice job Sorin😉 . just replace the second mosfet and will be chrarge agian 👍

[@emilianoortiz8795]

Hi I was watching your videos and saw something curious. Why does the Asus Vivobook with Radeon Graphics had like a plastic layer on the motherboard? Is it to prevent water damage or to other use.

[@seancurran1938]

A microchip that blows up. Amazing, possibilities are endless.

[@PaoloDiSciorio]

You have nice tweezers....please tell me where I can buy. Tks

[@bblod4896]

You left the shorted mosfet in place. Doesn't it protect the rest of the computer in case of a large current draw from defective components?

[@therzook]

With arduino to learn something, forget any silly notepads or anything like that, go through tutorials and so called sketches already in arduino software. Make sure that your first projects are dumb, literally dumb as there is some boring lot in the beginning, which you have to go through. Once you go through boring stupid stuff (it took me like 8 hrs coz it is really, really boriing), make your first project by pasting few bits of codes from ready sketches. Then you can start bigger things. My first useful project was RS232 monitoring tool - as I do some work on industrial PLC's serial standards 232 and 485 are used a lot in legacy stuff... Very useful this little thing is!

[@colinblakemore58]

Also would be interested in the Arduino videos. I am an experienced programmer but would like to have a go at programming one of these projects...

[@ohmware2020]

im excited with that arduino project sorin... combination of hardware and software... programming a hardware to work the way it should...

[@alenapatterson1431]

Input and output pins

[@kintag4459]

Thank you M.r

[@VerifyIT]

Love how you explain everything. I am also interested to learn Arduino with you. Already have a similar kit as well. Best wishes!

[@ohmware2020]

hello sorin, can you make a video about NEC TOKIN capacitors? how it works, symptoms when its failing, and how can we change or replace them... thank you

[@divingbike]

Pls follow up with the repair of the charging circuit and make a video on it!! I had the exact same problem where I bridget the mosfet to fix a dead laptop, as you did, and the notebook was on again but not charging. I changed also the charge IC after removing the bridge but nope, without bridge on the mosfet the notebook was dead again. So I'm really interested to know how you will fix it. Thanks in advance Sorin. ciao from Italy!

[@andreasreimer3929]

Have the same issue on a Toshiba satellite

[@Mr.Smith_Mr.Wesson_andMe]

And exchanging the bridged MOSFET with a new one won't help?

[@divingbike]

@@Mr.Smith_Mr.Wesson_andMe nope. Notebook with a new mosfet was still dead. Only way to let him start was bridge it. But battery was not charging

[@gaborpapa1515]

I had the same issue on an Asus X555. The solution was replacing the first mosfet! After that everything was fine.

[@divingbike]

@@gaborpapa1515 ahhh...maybe that is the key. If it will happen to me again I will try

[@veccloud1573]

Hi Master Sorin, (HeHe.. it sounds so Japanese 😀😀)... We all learn while doing mistakes. Only when you accept your mistakes, you learn, and become great, and that's you. You are just awesome... Just a doubt.. you have shown us many times how to get back those 19v rail. But what if you have 19v is all over the board but still no 3.2v, 5v, 1.5v etc.. You said they come via a power management chip. A tutorial about that would be very helpful.. Thank you Master Sorin

[@herrlip72]

I want to see you used low melts, it's amazing

[@bouxesas2046]

Sorin the sesame seeds from the bagel you were eating on the previous video probably shorted the power management chip. It's ok, it can happen to anyone.

[@bestbuildpc]

Where did you buy that electric screwdriver Maestro?

[@kiwuzopaul8341]

Nice one I like to learn ic programing

[@colinblakemore58]

What is the clear gel flux that you use in instances like this? I use your "home made" Rosin flux most of the time, but this clear flux you used here seems to be better for this type of job; I've looked but they all seem to be coloured rather than clear! Thanks. BTW., I've been watching your videos (all the way through, not 7 minutes! :-)) for the past three years; I think I've just about watched every one! I have learnt so much from you, so I would like to thank you for that. :-)

[@xpanza]

Hi Sorin, you can try to delete everything in battery section from device manager (Microsoft acpi....) That should wake your laptop to charge.

[@xpanza]

after restart

[@sanjayaabeygunarathna1990]

Dear Mr. Sorin laptop on just goes off but no shorts . please let us know how diagnosis through the videos your earliest respond is highly appreciated. thank you.

[@yehtut3209]

many thanks, sir.

[@sanjayaabeygunarathna1990]

Dear Mr.Sorin Lap motherboard on but no display and no shorts (doesn't go 0.8 A up) if u have a laptop like this issue, please let us know step by step how is diagnosis. your earliest respond is highly appreciated. thank you

[@EurekaRecycler]

Why did the super io blow? Do you leave the "bridged" mosfit in? Why did it blow? Thank you

[@digihorse6730]

Sorin. I'm a little behind on the videos, so only just heard about your interest in Arduino. I'm also trying to learn. Here's a project idea. What about a solar tracker for your solar panels so the panel moves to track the Suns movement for optimum charge rate?

[@obasicomedy]

Thanks for ur very best videos but am interested

[@aghackingofficial5473]

Hello Sorin I’m a fan of you and i wanted to ask you what school did you do to be able to repair computers TVs and stuff like that. I just want to get into repair and I don’t know where to start. Thank you!

[@martathamyou]

nice work... i have a question, from whare i can bay super io chip...?

[@paulzac5481]

Try ebay anazon alibaba, just google the one you want you'll find many

[@martathamyou]

@@paulzac5481 i know, but i wont sum one testing with programmer.... thanks

[@OverlandOne]

Another awesome video. Thank you.

[@progridha]

Thanks a lot sir for your videos

[@petartomic9783]

Yes ,arduino projects ,very interested ,ordered myself to ,so we can build together . it will be amazing.

[@ciprianpeica85]

when I saw the negative terminal also broken 🤣🤣🤣

[@RudolfXC]

No matter what your opinion, you should always return a laptop to the state when new, so replace any faulty components instead of removing a Zener or shorting out a MOSFET. Also, using solder containing lead has been banned in Europe since 2006 and I would be severely desciplined at work if I used it for repairs.

[@soeoo4659]

Very good work I like

[@The_Nirmal]

Where is your shop i need to repair my laptop from you only you pls reply

[@touati84]

Hi, what electrics screwdriver are you using? thank you.

[@VincentTubed]

thanks for sharing :). That makes it a good day.

[@TheMaxnux]

can say me where buy that electric screwdriver

[@mauanderuk]

Part 2 finishes breakfast.

[@thulinp]

Arduino is more fun (to me) when you can make something useful, and also something hard to make with just chips. Like a remote control receiver. I added a remote control volume and mute for my 1970s stereo. You can use nearly any old junk remote. Add an IR receiver and digital volume control chip.

[@neosrt10]

Hey bud how can I tell the Vbios apart from the regular bios on a laptop motherboard. I have an Omen 15 ce198wm with a i8750h dedicated GTX 1060 Max Q I need to flash the Vbios 8 pin back to stock I wanna use CH programmer with clip to avoid soldering on off.

[@rumenpetrov5755]

How much is the price for this repair?

How long the silicon hinges last? Has any of them came back for warranty?

[@groovejet33]

where you gonna get it fixed at?

[@atsuedwin]

yes i am interested in Arduino. I already started learning a few years ago. would be great to start again

[@melplishka5978]

Sorin are you going to start doing vids with arduino ?. That would be awsome. I’m just starting it too. 👍👍👍👍👍

[@Keythong]

I'm due for a new laptop soon, my current Dell is 6 years old and showing it's age. I think I'll give Lenovo a swerve, but should I get another dell, or choose a different brand next time? Any recommendations?

[@skaqruppasamy6591]

Hai sir Your service is nice, your service support same laptop ready thank you sir Sir Lenovo g50-80 same laptop junk display,next no bios setup not bootable problem I/o controller chenaged ite it 8585e same ic but no bootable , blank display not idea sir support sir

[@starmobiletech5161]

Very nice sir Thanks for Sharing 😊😊

[@0beejay]

That would be so awesome if you start a series on programming. I want to learn and we shall learn together. Love all your videos.

[@VideoServicesLI]

What pins did you bridge on the second mosfet?

[@davedanino2301]

hi i have an hp gaming laptop not coming on can i send it to u for repairs

[@yellowww21]

Hi, my laptop is a HP pavillion DV6. The laptop has no power yet, the charging light for 19V is on. I tested the bios chip and the 3.3V is present. When i shorted the first two pins of the power adapter, the fans of the laptop turns on yet there is not display in the screen. But when I connected the ribbon cable of the power button, there's no response when this is pressed. Tried reseating the RAM just like your previous videos, this did not fixed anything. Can you help me with this?

[@bestbuildpc]

Sometimes it is easier than you think. LOL. Always check cables first.

[@seraj98srour]

Please teach us how to build a soldering station with arduino, and lcd.

[@liveuk]

We have to do Lenovo training online then we qualify as partners. This then gives us full access to parts and schematics without buying copy illegal chips.

[@asfrancis2409]

dear sorin i have laptop for my son he use ardurino to run 24 volt motor and usb was in his laptop so the ardurino is damge and also the laptop not working any more if its posbele to send you the laptop to fix im living in holland and laptop is aser aspir 7 a715 one year old thanks francis

[@richardansay5433]

Its nice if you create video using arduino Sorin its the thing that we use in our engineering projects, i was able to create few projects using arduino and rasberry pi

[@gile849]

Nice build :)

[@mateoluz8399]

I had exact same problem with same voltage after second mosfet on G50 and problem was first mosfet(very tricky)

[@sureshkumar-vr1hh]

Good morning

[@BlackOpsJuJu]

been wanting to get into arduino also can't wait for you to do some vids on it Love all your vids and the way you each so looking forward to you learning and teaching arduino

[@simeonmihaylov6123]

Let's learn some arduino stuff together. I have one here and it has been sitting for like year and I've been trying to motivate myself, but...programming is tough.

[@ciprianpeica85]

We already know programming 🤣 but we want to see you do it.

[@rodelynpacheco9659]

sir how about black screen, it has power it has light on screen or LCD, but no display how to fix can you help me? thank you

[@redglory]

I would love a series with Arduino UNO! Great Sorin!

[@kaiserkhalil1]

Sir please make a video on smd NTC thermister and how to test it with multi meter...samsung mobile always have charging temperature issue...please help.... There are soo many NTC thermister soo its very confusing which to order.

[@marcellipovsky8222]

Ouch, my back opening cramped when I saw the board laying on the tweezers while Sorin was trying to power it on. 😢😢😢

[@lookatmepleasesir]

the romanian people deserve so much more

[@lazy8278]

I have a unique problem on my laptop.. my acer nitro 5 an515-42. Shows gpu temperature of 255°C on the nitro sense app. And when i turn on my laptop the keyboard blinks for some second at turns off.And it also shows charing every time even when i am not plugged in.what kind of problem is it?

[@astaroder2258]

Please help mine is Asus Intel core i7 3630qm k95vm motherboard

[@romaniainfo2542]

Da . Vreau sa învăț programarea Arduino. O sa fie distractiv.

[@afghanoutsider]

Please make video on it