Thanks for this video and the Amazon link for the kit. I bought a kit at Ace, but it didn't have the correct graphite washer. I don't know what I'd do without KZbin tutorials! 🤗
@DIYinspiredLewisBrantner3 ай бұрын
Perfect...... glad the information provided was helpful
@ffblegend4 ай бұрын
Thanks for the links and video! This helped me a ton because I have this same one and needed that kit. I did have issues getting my green cap off, the piece inside was stuck
@dwestman622 ай бұрын
Just complete this repair! Your video was perfect! Thank you SO much!
@DIYinspiredLewisBrantner2 ай бұрын
@dwestman62 thanks for taking the time to share
@anitracjones5 ай бұрын
I followed your instructions and fixed my faucet for less than $16! Thank you!
@DIYinspiredLewisBrantner5 ай бұрын
This is so awesome!
@DIYinspiredLewisBrantner5 ай бұрын
Glad this video was helpful!
@shelleymurphy6300Ай бұрын
T Y. I needed help with the top vacuum valve/anti-siphon piece. 😊
@ffgsimpson Жыл бұрын
Nice pace. Slow and steady
@DIYinspiredLewisBrantner Жыл бұрын
Thanks for sharing your comments! Have a blessed day!
@frankmbood225315 күн бұрын
Great video! Thanks!
@DIYinspiredLewisBrantner15 күн бұрын
thanks for taking the moment to share
@frankieortiz963128 күн бұрын
Very Helpful. Thank you
@DIYinspiredLewisBrantner28 күн бұрын
thank you for taking the time to share
@christiandshatto77654 ай бұрын
Ill give it a try on mine. Hope its easy as yours was
@DIYinspiredLewisBrantner4 ай бұрын
I know what you mean.... I have one in the back of my house leaking now so I will be completing the same exercise again
@robertcottle317 ай бұрын
Please don't forget the steel washer between the graphite and bib receiver
@jefferydossett4733 Жыл бұрын
Thanks Lewis
@DIYinspiredLewisBrantner Жыл бұрын
You're very welcome!
@DIYinspiredLewisBrantner Жыл бұрын
Thanks for sharing your comments
@terrylee6497 Жыл бұрын
It was helpful but I didn’t understand what you did after it leaked from the vacuum cap after installing the new parts?
@DIYinspiredLewisBrantner Жыл бұрын
it was little loose so I tightned it up and all was good
@blueboxstar5284 Жыл бұрын
@@DIYinspiredLewisBrantner it would of been nice if you actually showed when you were tightening it
@DIYinspiredLewisBrantner Жыл бұрын
@@blueboxstar5284 yes. It's at the 8 min 30 second mark
@DIYinspiredLewisBrantner Жыл бұрын
Thanks for watching
@SKBhunia4 ай бұрын
I am following your very helpful video to repair mine. I am at 0:45 time point in your video, but can't go beyond that. The valve stem isn't coming out even after turning and pulling with a wrench. Any suggestion? Spray WD40?
@DIYinspiredLewisBrantner4 ай бұрын
Hmmmm, my guess is it will come out..... my suggestion is just tug on it more as you turn it..... try that.
@ffblegend4 ай бұрын
If the top cap has a little drip, it’s super tight. Should I use plumbing tape to fix the drip?
@DIYinspiredLewisBrantner4 ай бұрын
I replaced a second one at my place and the same thing happened. I took it apart again and saw I pinched the flapper part so I reused the old one..... that worked for me
@ffblegend4 ай бұрын
@@DIYinspiredLewisBrantner I was gonna use my old one but it got destroyed since it was stuck inside. I had to beat it up pretty bad.
@michaelcena3589 Жыл бұрын
Dont you have to tighten with a tool that piece as well on minute 8:54? I ask because mine was leaking a bit of water out through it for 2-3 seconds everytime I closed the faucet so I tighten it a bit with my tool and it stopped leaking.
@DIYinspiredLewisBrantner Жыл бұрын
Yes, this clear plastic piece needed tightened too. I had to go back and tighten it also.
@DIYinspiredLewisBrantner Жыл бұрын
thanks for sharing your comments
@Doamino415 ай бұрын
My spigot looks similar to yours except mine doesn't have that syphon knob on top. Would that make a difference on a valve stem repair?
@DIYinspiredLewisBrantner5 ай бұрын
Great question..... not sure. Maybe you could take yours apart to see if the parts look the same. You could put it back together if it isn't. Just make sure you have the water shut off inside
@Doamino415 ай бұрын
@@DIYinspiredLewisBrantner Thank you. It doesn't leak but part of the stem that's connected to the nut you take off is broken and the handle doesn't fit right. So I'm wanting to replace the valve stem and nut, if it's possible.
@feldredge50772 ай бұрын
Mines the same real old school one. Guess I can paste a pic
@Saint696Anger Жыл бұрын
I just ordered the kit off your link but in your package I saw you had two kits?
@Saint696Anger Жыл бұрын
Package in the video*
@DIYinspiredLewisBrantner Жыл бұрын
I ordered 2 of them. I have one of these in the front of my house and one on the rear side of my house
@DIYinspiredLewisBrantner Жыл бұрын
Wonderful..... glad the video was helpful
@Saint696Anger11 ай бұрын
@@DIYinspiredLewisBrantnerSo mine says it's a Prier C-144/C-244 on the airwave cap. I received the kit and they don't look exactly the same parts. Is the kit I ordered a multiple type fita? I ended up using the old parts along with a peerless plumbing repair assortment kit I bought a long time ago
@DIYinspiredLewisBrantner11 ай бұрын
@Saint696Anger interesting..... not sure..... great to hear you got yours fixed
@simon234 ай бұрын
Why the background music? We're trying to listen to the speaker.
@DIYinspiredLewisBrantner4 ай бұрын
Sorry...... I didn't realize it was that loud.....
@talans252 ай бұрын
For positive vibes bro 😅
@JisellyPlayz9 ай бұрын
Did you have to order the graphite washer separately?
@DIYinspiredLewisBrantner9 ай бұрын
No, it came with the kit
@dinhchieunguyen6842 ай бұрын
the video is good but no music is much better
@DIYinspiredLewisBrantner2 ай бұрын
I agree, the music was too loud.
@STOCKmarket-fo1fhАй бұрын
Htae that mucis..
@DIYinspiredLewisBrantnerАй бұрын
I agree..... it is louder than what I would have liked. Lesson learned.... all the videos since then has a much softer tone. Thanks for taking the time to comment.
@1jantheman1 Жыл бұрын
Magic fix off camera. Kinda defeats the purpose.
@DIYinspiredLewisBrantner Жыл бұрын
Not following your comment, what does Magic fix off camera mean?
@1jantheman1 Жыл бұрын
@@DIYinspiredLewisBrantner 10:35 you say you need to tighten a couple things up because it still leaks, but do not show you fixing it unedited.
@DIYinspiredLewisBrantner Жыл бұрын
@@1jantheman1 correct, under the silver cap, that plastic piece needed tightened up some more. As you saw in the video, I only placed that finger tight. I removed the silver cap and then tightened it more, then put the silver cap back on and it was good to go. Thanks for clarifying