A TCM electric forklift where the lift cylinder is able to lift but cannot lower by pulling on the lift/lower lever. The video shows the process of diagnosing the problem.
Пікірлер: 37
@sebastianibanez38124 жыл бұрын
Thank you for these videos!
@jesiedoromal38734 жыл бұрын
Nice sir, so informative, galing ,more video poh salamat
@niranjankumarmahto67902 жыл бұрын
Thanks you sir very very nice knowledgeable video ok
4 жыл бұрын
nice content
@rscelectrical70914 жыл бұрын
Nice job, sometimes the smallest parts can cause what seem to be the biggest problems.
@forklifttechnicianguru51262 жыл бұрын
Good 👌👌👌👌
@danielmariduena56774 жыл бұрын
Very smart way to solve problems. One question, where did you find the resistors ? I mean in what part of the lift truck
@forkliftgeek104 жыл бұрын
Left hand side of the battery compartment.
@danielmariduena56774 жыл бұрын
ForkliftGeek thank you !!
@MrDannyP198311 ай бұрын
How would I get a wiring schematic for a reach truck I'm trying to repair?
@automotivediagramsreading97114 жыл бұрын
Thanks for your time...where do you get your wiring diagrams thank you againg.
@forkliftgeek104 жыл бұрын
Most of them are provided by the company. Some I bought online. Too expensive from dealerships.
@kapilkumarpathak64843 жыл бұрын
CAT 966H wheel loader problem in lift cylinder not working I need to help with me
@amzilyoussef808015 күн бұрын
Hi, sir My forklift don't start in the ignition switch and hydrauliic system don't work . I connect directely the postif of starter with the excitor it runs the engine but the hydraulic system don't work . When i make chunt in the starter relay . It runs also but the hydraulique system don't work
@rodlouiefacun36993 жыл бұрын
Hi sir! Good day. Our forklift has an error. We change the battery then when we start it error codes pop ups *OFF HYD-LEVER TO NEUTRAL * whats the problem with that. Hope you help us. Thank you in advance
@markonujic85943 жыл бұрын
Hi, what do you check when toyota tonero forks dont stay when you lift. They just drop down slowly when not using the controls???
@forkliftgeek103 жыл бұрын
Either the cylinder or the control valve is internally leaking.
@user-oy2ie8qo3g Жыл бұрын
Thanks Where can I find the circuit diagram for this lever? electrical diagram
@forkliftgeek10 Жыл бұрын
Either you buy it online or from the dealer
@andorassebastianbarabas659 Жыл бұрын
please could anyone give some tips why machine doesn't lift up! charger is good
@anilthakur114211 ай бұрын
Forklift Lift r not use proply. I have up in lift but limit switch r not work proply. Screen show 4:1 .wts a prblm. And how to change micro switch. Send me a vedio plz
@akmmechatronics56903 жыл бұрын
I have RR B3 reach truck error E107 occurs after some working with reach truck. Anybody tell me what is the problem. I have replaced the battery but same condition
@marclawson34533 жыл бұрын
The main contactor K10 does not close during truck start up and the emergency stop switch does not operate 1, defective k10 contactor tips 2, defective a5 card Check voltage at pin 808 on a5 card voltage must be battery voltage on start up. If no voltage check fuse f62 (10amp) If fuse is ok check contactor tips,
@akmmechatronics56903 жыл бұрын
@@marclawson3453 it's due to battery. Battery is weak. I have also replaced the MCU. After replacing reach speed issue occurs then I have done calibration. Machine doing it's all functions good. But after some days reach speed problem again occurs. Can you please share with me why this is happening?
@marclawson34533 жыл бұрын
@@akmmechatronics5690 what do u mean by mcu? If the battery is faulty then it will cause the contact tips to arc and burn out. Check the contactor under the seat and see if there is any burn marks. Contractors are cheap and I could probably get u the part no, don’t understand why u are changing computers before trying this
@marclawson34533 жыл бұрын
@@akmmechatronics5690 remove the floor plate and check the spring under the brake pedal, the spring snaps and it will throw a fault code and cause the reach to go in and out slow, I think it’s parameter 38 or 28 u need to go into to calibrate it, fault will keep appearing if the spring is broken tho
@akmmechatronics56903 жыл бұрын
@@marclawson3453 yes you are right. Some time error 16 and 17 occurs. It's due to break and accelerator press. Can you please share your whatsapp number?
@keleycariaso86 Жыл бұрын
sir how about toyota diesel engine only lift up function lift down no function?
@forkliftgeek10 Жыл бұрын
Then I would check if there is a mechanical binding in the mast, cylinders. If none then it would have to be in valve bank.
@keleycariaso86 Жыл бұрын
@@forkliftgeek10 thanks highly appreciated
@torreshl762 жыл бұрын
ECU Fuse! 😅🤣😅🤣😅🤣
@DharmendraYadav-dt2cd2 жыл бұрын
Aur clip current problem Sar Hindi mein banae video