LMTVs have cruise control standard. To engage it, you wedge your M4 between the seat and the gas pedal.
@rronmar4 жыл бұрын
Keeps it close at hand also:)
@elgoogsucks90054 жыл бұрын
I have the older model where cruise control comes standard too. It is the lever on the right side of the dash. The brake doesn't disengage it so much as "override" it...
@rronmar4 жыл бұрын
@@elgoogsucks9005 that would actually be easy to fix. Small air cylinder and solenoid valve connected to the brake light circuit. Retards the hand throttle when the brake lights activate...
@elgoogsucks90054 жыл бұрын
@@rronmar that is more elegant than my current work around which is to pull up on the steering wheel and push down on the brake as hard as i can. : )
@DekeDieken Жыл бұрын
A brick works okay too.
@Certawin4 жыл бұрын
Nice addition, will make long trips alot better I think. Well the bloopers are a riot. Have a great rest of your weekend.
@Alaskadirtfishing4 жыл бұрын
Glad to see a new video. Outtakes were great. 👍
@happytreesllc63693 жыл бұрын
pin # 59 - Cruise control on/off switch pin # 35 - Set Pin # 44 - Resume Pin # 45 - Service brake pedal position switch (you did not need to splice in your situation as you did not need anything, just a few Deutsch connectors, some wiring, and LED light. you can easy to remove the connector from the plug, just need Deutsch removal too ( under $10 ) Thanks for the video. I did enjoy it a lot. Good project.
@nickdouglas92983 жыл бұрын
Amazing build
@Frisky05634 жыл бұрын
Merry Christmas Chad. You have me laughing with out takes
@EmilderGraue4 жыл бұрын
Great Video and Great Outtakes
@mvdb51504 жыл бұрын
Hi Chad, mine works perfect. Still have to intall the dashlight...
@rack00414 жыл бұрын
As usual great job! NOW get into the box and start knocking out the living quarters!!
@BrokeOverLand4 жыл бұрын
Just for that I’m going to build it all out of cardboard and 2x2. :)
@rack00414 жыл бұрын
LMAO
@BackpackerCoach3 жыл бұрын
You make it look so easy.
@joeabbott21123 жыл бұрын
Love the Show Chad
@dflood3164 жыл бұрын
Great video and outtakes were funny. Unfortunately this solution is not an option on our 3116.
@traxoffgrid4 жыл бұрын
Very nice set up. Wish that was installed when I drove it lol
@BrokeOverLand4 жыл бұрын
I’m sure you’ll get the chance to drive it again. :)
@SeanFillner4 жыл бұрын
Nice kit. I am stuck with the hand throttle unfortunately :D.
@ryanwalsh92553 жыл бұрын
Is the hand throttle a viable option for the 3116? I haven’t really even touched the thing.
@NEILSWORLD4 жыл бұрын
Now you're cruising 👍. I think I need an a1 for several reasons 🤣.
@dustup22492 жыл бұрын
Good informative guide here. Question: Does application of engine brake only temporarily pause the cruise control the same way the brake pedal does?
@BrokeOverLand2 жыл бұрын
I have not tested cruse with the engine brake enabled. Since there is a direct connection with the brake pedal to the cruse control system and no connection to the engine brake, I don’t think it will interrupt the cruse setting. But I would need to test it to be sure.
@dustup22492 жыл бұрын
@@BrokeOverLand Thanks for responding. I was curious how detailed the ECM was mapped. I was trying to account for all the wires you plugged into it's connector and thought maybe the engine brake situation was mapped.
@ethanturner55674 жыл бұрын
I have the same kit sitting in a box on a shelf... Thanks for the how-to, the ecu pin install had me worried, but thanks to your vid it looks like a snap. Did you previously have CAT change your ECU Cruise parameters? Normally you'd have to set Low & High speed parameters in the ECU...
@BrokeOverLand4 жыл бұрын
Yes I had CAT set the ECU while I had it in for the rear main seal.
@ethanturner55674 жыл бұрын
@@BrokeOverLand, did they recalibrate your speedo and CTIS overspeed too?
@BrokeOverLand4 жыл бұрын
@@ethanturner5567 I had the speedo recalibrated and now it’s 3mph off at 60. So I’ve been trolling the sites for non knock-off CAT ET to just do it myself.
@ethanturner55674 жыл бұрын
@@BrokeOverLand , did you recalibrate it to my numbers? 49325 P/mile? Worked for me and Matt Molenhouse. We all have 2003 A1's...
@BrokeOverLand4 жыл бұрын
@@ethanturner5567 yep those are the numbers they programmed them to. I need to ru it with the reader attached and see what the ECU thinks the speed is vs what the speedometer thinks it is.
@pierretrudeau55493 жыл бұрын
i have a cat 3116 in my m1084 1996....can i add a cruise control or it s impossible
@BrokeOverLand3 жыл бұрын
I honestly don’t know. I have not searched for a cruse system for the 3116. The 3116 is all manual throttle control vs the 3126’s computer controlled system.
@NateVolk4 жыл бұрын
Did you not have to do anything to the factory ECU? I heard you have to program it to allow CC to be used on the 3126...
@ethanturner55674 жыл бұрын
Normally you'd have to reset the cruise control Low Speed & High Speed settings. Factory default is set to 15mph high and low.
@walterstech78938 ай бұрын
You mentioned this mod works for C7 and 3126B engines. Looking at buying an A1 truck. Any idea if A1 came with both B and non-B 3126 engines? Is the non-B 3126 a non-ECU engine? Is that why it won’t take this mod?
@BrokeOverLand8 ай бұрын
It will work for any of the 3126’s you’ll find in an LMTV. The difference between 3126 a,b,e is mostly just noise and emissions changes.
@christiandaniel544 жыл бұрын
Hi Chad, I would like to know how much insurance you pay for the m1078?
@SlikeAnubis4 жыл бұрын
Pray tell what is the green digital display on the top of the left dash ?
@BrokeOverLand4 жыл бұрын
It is a GPS based speedometer. I didn’t fully trust the speedometer in the truck after swapping to 3.07 gears and having CAT change the shaft rotation count in the ECU.
@SlikeAnubis4 жыл бұрын
@@BrokeOverLand thanks !!
@tehNashty3 жыл бұрын
Hey, man. I miss the intro. 🥺 Does the remote need a battery? I was thinking about using a stalk instead.
@BrokeOverLand3 жыл бұрын
The into is back. :). Yes the remote needs a battery. I haven’t had to change it yet so It seems to have a long life.
@Hank000118 ай бұрын
Any chance anyone knows where to get one of these nowadays? E-bay link is a no go and I'm not having much luck elsewhere.
@BrokeOverLand8 ай бұрын
I just talked to Berend, the wireless modules are no longer manufactured so he is unable to make more units at this time. We’ll have to see if anyone else knows where to get them.
@jameswaters3132 жыл бұрын
What were you going to do if the brakes didn't disconnect? Lol
@BrokeOverLand2 жыл бұрын
Scream like a little girl…. Then probably hit the off switch. :)
@elgoogsucks90054 жыл бұрын
I was going to unsubscribe because your videos are demoralizing, but watching that dash eat your hand and you dropping the screwdriver through the engine gives me hope.
@marcfournier8233 жыл бұрын
Withe the ease of installation you could call this a curse control.