In case you take this apart again or anyone else does, I found that instead of removing the big bolts it was easier to remove the two Allen screws attached to the black housing and pedal. Made it way easier when trying to compress the stiffer springs and fit them back.
@JCCollinsRacing Жыл бұрын
That's a great tip! I didn't think of that. Thanks!
@miguel.meizoso10 ай бұрын
So this means you can do all this without even removing the back plate? itll help a lot
@shaqdaddythepunisher783410 ай бұрын
@@miguel.meizosono, you still need to remove the housing like at 10:38 . What I said just helps with removing the springs from the pedals. You don’t need to even put all of the screws back into the back plate when done. I found the outside ones are fine. The screws underneath the carpet gripper are difficult and aren’t needed to hold the housing together.
@doriastein60019 ай бұрын
@@miguel.meizosoI modded mine and never took the back plate off, if your just needing to get to the springs I’ve found there’s no reason to remove the back plate or the actual pedals. As stated earlier remove the screws behind the pedal instead of the ones at the base, it’ll be much easier to re-assemble!
@sfacco5 ай бұрын
yup, other upgrade videos just remove the 2 Allen screws in the pedals, that's absolutely easier as you just need to push the pedals in position.
@Femos932 жыл бұрын
1 year later and this video is still helpful! Thanks for the video!
@JCCollinsRacing2 жыл бұрын
@Femos thank you! I'm glad you found it helpful!
@CarlosDiaz-xj6zb3 жыл бұрын
I'm glad i found your channel just as small as it is. Love your work and thanks to this kind of mods all logitech g29 users can enjoy this. I just bought an upgraded 6-r h gearbox from aliexpress, an adaptor for a 14 inches steering wheel and i already have the drift handbrake installed. I'm going all in and better informed with your video, big thanks and i hope your channels gets out there!
@JCCollinsRacing3 жыл бұрын
@Carlos Díaz Rodriguez thanks for checking me out and for the feedback! Those are some pretty serious hardware!
@steam-SMOKEY2 жыл бұрын
Appreciate this upload mate, new to sim racing and purchased a g29 (I heard its a Good entry level wheel) and the pedals felt wrong to me but after watching you and afew changes for personal preference the pedals feel alot better now. Cheers 🍻
@JCCollinsRacing2 жыл бұрын
@Junior glad this helped! Welcome to Sim Racing!
@steam-SMOKEY2 жыл бұрын
@@JCCollinsRacing cheers mate, ACC and iracing is my go too. What you bashin? Only asking to broad my collection of racing sims. Stay blessed 🥃
@JCCollinsRacing2 жыл бұрын
@@steam-SMOKEY ACC, AC, F1 2021, and just starting rFactor 2
@mikepiehl9292 Жыл бұрын
Watched this video before I did my mod today and sure glad I did. Two tips (although Shaqdaddy's sounds best and I'd try that if I did another.) 1) No need to totally remove the clutch bolt. Just make the inside tip flush with the right "wall" to provide some room. 2) If you have a Dremel, use it to create rounded notches in the left side runner walls so the bolts can come out and go back in straight, rather than at all angle. Same for the Accelerator pedal. I Dremelled mine after I removed and the re-assembly was simple. Wish I'd have done it before removal. Great video! Thanks!
@JCCollinsRacing Жыл бұрын
That is great feedback and an even better suggestion! Thank you for watching, and I am glad that this video helped you!
@Jay_Hova4202 жыл бұрын
Happy I found this channel.. I'm going to purchase the kit for $10 off ebay and do the mod to brake, clutch and gas pedal I want my G29 to feel as real as possible..
@JCCollinsRacing2 жыл бұрын
@Jay Hova420 glad to hear that! Those upgrades will definitely make the G29 feel more realistic. I am speaking from experience. It would be nice to adjust the amount of travel in each pedal, but the stiffer springs and damper help tremendously!
@Jay_Hova4202 жыл бұрын
@@JCCollinsRacing ok I will get the damper kit you have listed from ebay and the upgraded springs from Amazon..
@driesschoubben1691 Жыл бұрын
This video helped me very much. Clear information, thank you! Grts from Belgium sir.
@JCCollinsRacing Жыл бұрын
@driesschoubben1691 you're welcome! I'm glad that it was helpful to you! Thank you for watching!
@Mainstayjay8 ай бұрын
Hi. I just finished swapping out my pedal set brake potentiometer to one from Axs Sim. I had that pedal flicker issue and cleaning the stock potentiometer didn't completely fix it. I found that Axs Sim makes a closed potentiometer and bought two of those. The brake pedal is working great again which I am pleased with but I thought about looking into getting more realistic braking so here I am. This looks like a good solution, I am going to give it a go. Thanks for this walk through!
@JCCollinsRacing8 ай бұрын
@Mainstayjay you're very welcome! Thank you for watching!
@ovase11232 жыл бұрын
Very VERY underrated channel!
@JCCollinsRacing2 жыл бұрын
@ovas E thank you!
@yeahrightmate Жыл бұрын
I have an easy fix for putting your pedal back together, before you take it apart just compress the pedal about half way down and then drill a small hole about 2mm right through the 2 pieces of the piston and insert something like a 2mm allen key right through and it keeps it together already compressed so you can just undo the bold and lift it out as one.
@JCCollinsRacing Жыл бұрын
@Yeah Right that's a good fix to keep pedals in place. Thanks for sharing and tuning in to the video!
@yeahrightmate Жыл бұрын
@@JCCollinsRacing Yes it sure makes it easy to assemble when you have a strong spring that you have to compress while you get the bolt in.
@technoplex3953 жыл бұрын
This video came out at the perfect time because I'm thinking of morning my pedals and shifter
@JCCollinsRacing3 жыл бұрын
@TECHNOPLEX I'm glad that it helped! Modding the brake pedal makes the largest difference between the 3, in terms of faster lap times. The added resistance of the pedal helps to establish solid and repeatable muscle memory. How stiff do you think you want to make your pedals?
@technoplex3953 жыл бұрын
I want my pedals to fill as realistic a as possible
@technoplex3953 жыл бұрын
Btw I'm using ps4
@JCCollinsRacing3 жыл бұрын
Nice! If you decide to get into PC gaming, this set will still work. Setup is really easy with through the Logitech G Hub software.
@technoplex3953 жыл бұрын
Awesome
@aidangomes82062 жыл бұрын
great video most people dont give a list of tools which was very helpful so thank you
@JCCollinsRacing2 жыл бұрын
@Aidan Gomes you're welcome!
@_J.Collins2 жыл бұрын
Great walk though sir, from one JC Collins to another!
@JCCollinsRacing2 жыл бұрын
@Joe Collins haha! Us JC's jave to stick together! You're welcome! I'm glad it was helpful! Thanks for tuning in!
@asherwiggin64562 жыл бұрын
Very comprehensive and informative video. Very well made. Great Job!
@JCCollinsRacing2 жыл бұрын
@Asher Judd thank you!
@gustavogago32599 ай бұрын
Awesome! Im actually glad i watched this
@JCCollinsRacing9 ай бұрын
Thank you for watching!
@stevenhenson49562 жыл бұрын
I think you should make the tutorial on tutorials haha good job dude amazing work. I now feel confident that if i wanna do that mod i can easily.
@JCCollinsRacing2 жыл бұрын
@Steven Henson thank you for the encouragement! I am glad that this makes you feel confident!
@stevenhenson49562 жыл бұрын
@@JCCollinsRacing and its done bro ty for the help.... personally brakes perfect with the gteye spring , tho on throttle I want to swap out the spring for the gteye clutch
@sweetbabe-zf5zf Жыл бұрын
I wonder why they designed the stock breaks to be so shitty
@JCCollinsRacing Жыл бұрын
@sweetbabe 1234 lol!
@rapperodebarrio2 жыл бұрын
I do perform my mod early today but I will try it tomorrow morning following your steps!! Thanks
@JCCollinsRacing2 жыл бұрын
@TJones24 you're welcome! I'm glad it helped!
@HPAGamer9 ай бұрын
Bro i'm glad to see your video that me helped a lot thank you!
@JCCollinsRacing9 ай бұрын
@HPAGamer you're welcome! Thank you for watching!
@theVersatileGamebox3 жыл бұрын
very good illustration. keep it up
@JCCollinsRacing3 жыл бұрын
@Damond's Assorted Topic thank you!
@DaveGSound2 жыл бұрын
Great vid! Thank you
@JCCollinsRacing2 жыл бұрын
@DaveGSound thank you! You're welcome!
@GoingTrackSideinAlberta Жыл бұрын
Best recommendation for Logitech G29 pedals is Ricmotech LC27-3 Logitech Load Cell Kit V3 paired with Leo bodnar cable
@JCCollinsRacing Жыл бұрын
Oh really? I never heard of this. Thank you for suggesting it! I hope that everyone in this thread can benefit from it! Does it install similarly?
@00Clive003 жыл бұрын
Good video, saved me some time taking to out to many screws out. I've got the g923, so the break pedal has a different spring to the G29, it's more progressive and actually feels pretty good out the box. I added a 6mm mod piece to the clutch and a 10mm mod piece to the accelerator pedal, feels much more natural to me. I also added some very thick tape where the pedals pivot and touch the bottom of the metal base, reduces that loud metal on metal banging sound when the pedal reaches 100% and returns quickly to 0% positions, it reduces it to more of a thud, still makes a noise, but not as irritating as stock.
@JCCollinsRacing3 жыл бұрын
@00Clive00 thank you! I did not think to add some tape as a buffer for the pedals, that is a great idea to keep the sound to a minimum. I heard that 923 had an upgraded brake spring, and glad to hear that it is more progressive. How do you like the "True Force" (I think that's the name) ffb?
@00Clive003 жыл бұрын
@@JCCollinsRacing No problem, it's great to share ideas, anything to make it feel a bit more realistic and to not piss off the girlfriend 😅, I'll probably check out a few of your video's, I just took delivery of the playseat challenge after using a crappy xrocker metal stand and office chair, need to attach the handbrake and gearshifter. I don't have experience with any other wheels and pedals, other than 18 years with real cars, ranging from Honda Jazz to BMW E36 M3. The g923 brake pedal feels very natural to me, definitely has a progressive feel, would compare it something like a VW golf, it's comfortable to use, but takes decent amount off pressure to hit 100%. Of course it won't compare to a the weight a race car needs or better SIM pedals, I did fit a 6mm mod piece in the brake pedal and tested it with my hand, decided to leave it out, I haven't used the playseat yet, but as I'll be able to stamp on the pedal more I might want the extra pressure and put it in.
@00Clive003 жыл бұрын
@@JCCollinsRacing I tested trueforce in Dirt Rally 2 and it felt awful, just made the wheel rattle like crazy, so turned most of it off except the trueforce effect where it vibrates when you rev the engine, nothing special. I had a better experience with it in Forza horizon 4, it was much more subtle, like a bit of vibration whilst driving down a dirt road, it added to the experience, but not a good enough reason to upgrade or pay more for the g923 over the G29. I bought mine second hand for £160.
@JCCollinsRacing3 жыл бұрын
@@00Clive00 the Playseat Challenge will definitely give you that added stability while braking! I also started off with an office chair and table for the wheel base. I was always rolling backwards whenever I pressed the brake and it definitely effected my lap times in a negative way. You will definitely feel more consistency in your racecraft because of the added stability the Playseat Challenge will give you. When you receive your Playseat, I would definitely be grateful if you check out my Playseat Challenge review and shifter installation guide videos! They will get you started with setup, along with a few things to consider. Did you race those cars that you have experience with?
@JCCollinsRacing3 жыл бұрын
@@00Clive00 that's really good to know and not a bad price for the G923. Thanks for that. I have been curious about how much of a difference the TrueForce makes. I wonder if some of the clipping can be addressed with a more powerful power unit... You should check out my video, "5A = Better FFB???". It addresses the effects of more amperage to the G29/G923's ffb and clipping during sim-play. I tested a stronger power unit on AC, ACC, and F1 2021. There is noticeable difference in the ffb smoothness with reduced clipping. Check it our and let me know what you think.
@MatthewBS929 ай бұрын
Very good video thank you! You finally make me take the decision to buy the 3Drap mod. The installation is not so complicated with your instructions so great job. I have just one advice for the "beginners" that doesn't have a fixed simracing rig like me (I own the Playseat Challenge). Based on your experience, I purchased the Formula version still keeping the G29 original spring: I find this WAY too stiff! The Playseat is lifting off when I stomp on the brake to get to 100%😂 Also, as I am playing with bare foots (only socks), my foot it's kinda hurting after little bit. I regret not having purchased the GT version (or maybe the Console one). Is someone using Playseat Challenge and any of 3Drap mod? What 3Drap version do you suggest?
@JCCollinsRacing8 ай бұрын
@MatthewBS92 That is a really good point. The formula spring/elastomer combo is VERY stiff, and I noticed that I was pushing back in the PSC, too. It took a ton of tweeking, but I was able to find a happy medium with braking sensitivity in GHub. If you are on console and don't have a solid rig, I agree that the GT Elastomer is the better option. Thank you for highlighting this point!
@karl531333 жыл бұрын
I just tuke the rubber block out of the middle of the spring and put it back together with the original spring feels just fine not to soft or hard....
@JCCollinsRacing3 жыл бұрын
@karl53133 yeah, taking out the rubber block makes a really big difference in the travel and tension during hard braking.
@vicar19 Жыл бұрын
Yes man.. mine hasn't even come yet, and I'm already planning on doing this 😅
@JCCollinsRacing Жыл бұрын
Awesome!
@MikeTDF Жыл бұрын
Finally i decided what mod to buy to make my Logitech pedals feel better, so i bough a set of Fanatec CSL LC pedals! :D
@JCCollinsRacing Жыл бұрын
Nice! How are you liking the CSL LC pedals?
@orwell_fan8 ай бұрын
Just got a G920 yesterday and removed the rubber thinge lol
@jjules23 Жыл бұрын
Thanks!
@JCCollinsRacing Жыл бұрын
@jjules23 you're welcome! Thank you for watching!
@vitorarbex2 жыл бұрын
Great Video, can you talk about that softer mod that was instaled in the brake before you started, its harder than the stock rubber? any good points for it?
@JCCollinsRacing2 жыл бұрын
@Vítor Arbex thanks! The original rubber that is in the brake pedal is harder than normal rubber. It's really dense and when the brake is pressed, it does not feel natural. The original spring is soft, so the initial travel in the pedal is not progressive and hard to judge. With the rubber block being hard, there is a hard stop in the braking before the pedal is fully compressed. It makes judging braking distances and trail braking very difficult.
@jayhendrix734325 күн бұрын
Great vid 😃 I just took the plunge & bought my 1st steering wheel being this g29. Only thing that bothers me is exactly is the stock setup on braking. My question is, can anyone give me the length (from eye-to-eye) on this thing? Im thinking on using an alloy dampened shock from an rc with a stiff spring Tia
@JCCollinsRacing20 күн бұрын
Thank you! I don't know the distance, but the spring mood set I bought did the trick! Here is a link for a similar spring set. MORICHS Upgrade Mod Brake and Throttle Pedal Spring Kit for LOGITECH G27 G29 G920 Racing Wheel a.co/d/bzv8QGh
@jayhendrix734320 күн бұрын
@@JCCollinsRacing already tore it apart and figured out. Used HPI alloy shocks off a C1 using 80w oil and the stiffest spring from the pedal set (silver) Feels hydraulic and i love it Thanks for the response 😉
@XsnipxrmainX Жыл бұрын
I honestly feel like the brakes are fine once you have them set on a cockpit just my opinion. great video though man.
@JCCollinsRacing Жыл бұрын
Thank you for watching and thank you for your opinion! I can imagine that it feels better on a sturdy rig. If the pedals are rigidly secured, then it becomes easier to modulate the pedal with the stock hard rubber block installed.
@XsnipxrmainX Жыл бұрын
@@JCCollinsRacing thanks for the reply man earnt a sub 🤟
@JCCollinsRacing Жыл бұрын
@@XsnipxrmainX no problem! Thank you very much for the sub!😁
@strikedshorts8672 жыл бұрын
I know this is about a year on from the video being released so not a great chance you’ll reply but with the throttle Did u just switch the spring out with the Glodom (or whatever it’s called) higher tension spring or do something else. Plus your channel is amazing I’ve literally got my playseat challenge and my g29 because of ur reviews.
@JCCollinsRacing2 жыл бұрын
@Striked Shorts thanks! I'm glad my reviews are helping you make an informed decision! For the throttle, I just swapped the spring for a stiffer one. The extra resistance makes throttle management so much easier!
@JCCollinsRacing2 жыл бұрын
@Striked Shorts yes, I used the throttle spring included in the Glodorm kit linked in the description of this video.
@strikedshorts8672 жыл бұрын
Thx for replying so long after the video was released. And one more question. Just to reassure me. Did u also use a 6mm pre dampner in the throttle?
@JCCollinsRacing2 жыл бұрын
@@strikedshorts867 Yes, 6 mm if I remember correctly.
@octogames68232 жыл бұрын
Oh you guys can get to the peddle from the back with no disassembly to the housing. I figured that out the third time I took mine apart.
@JCCollinsRacing2 жыл бұрын
@Octo Games really? I didn't know that. How can you get to the pedal without disassembly?
@octogames68232 жыл бұрын
@@JCCollinsRacing the two screws behind the pad on the peddle. Its a little bit of a pain putting the screws back in so use a flathead to leverage the spring tube back in place.
@JCCollinsRacing2 жыл бұрын
@@octogames6823 thanks for sharing this tip!
@Dexterzlabs11 ай бұрын
G920 comes already with the chrome spring in the break
@DaniloGuic7 ай бұрын
I have a playseat rig. Just bought the hard kit. Just affraid the stiffness will be too hard and mess my rig. Would it had been better to buy the medium option? I think 3drap changed the product and made an upgrade. Hope it works ok. Thanks!
@JCCollinsRacing7 ай бұрын
@DaniloGuic it won't be too stiff. I ran this upgrade on my Playseat for a long time and had no issues at all with it being too stiff. I hope this helps. Thanks for watching!
@Bread_train4 ай бұрын
How to arrange wires
@octogames68232 жыл бұрын
I used the same bushing insert for about a year and Im finding myself smashing the brake with no real control. Now im a better driver, I noticed the brake mod is my biggest issue. Im going to cut the bushing down about 50% and see if that helps. If not I will print up a new one with a lower shore value.
@JCCollinsRacing2 жыл бұрын
@Octo Games nice! What material are you using to print the bushing?
@octogames68232 жыл бұрын
@@JCCollinsRacing The original was purchased. I have a spool of polyflex TPU95 I want to try with a lower infill. The purchased one looked like a 25-30% infill so I will try a 15% with the filament I have.
@BaldingChief542 жыл бұрын
is the yellow thing stiffer or less stiff than the rubber block? my leg just hurts because i have to press too hard and I'm wondering if the yellow insert makes it better
@JCCollinsRacing2 жыл бұрын
@Viper TD it is less stiff and is intended to be used in conjunction with a spring (soft or stiff) to allow for more brake travel and still provide a simulated progressive stiffness while being depressed. So, your keg should not hurt nearly as much. You will be able to gage your braking better and have more travel. This will put less pressure on your leg.
@richmeier8 ай бұрын
Does the stiffer spring in throttle help throttle control and feel more like pressing gas in real car? When drifting corners I gotta use my big toe like SpongeBob in boating school to ease the throttle
@JCCollinsRacing8 ай бұрын
@richmeier lol! Yes, the stiffer throttle spring makes a huge difference and feels more realistic! The added resistance makes it much easier to modulate the throttle vs the original weak spring that feels like an on/off switch.
@richmeier8 ай бұрын
@@JCCollinsRacing awesome! Gonna try these mods out, and possibly an inversion kit.
@raisin392 жыл бұрын
I recently bought my G29. It seems like there must have been a upgrade because this brake is firm.
@JCCollinsRacing2 жыл бұрын
@The Russ Show does the pedal feel like it hits a hard wall after being fairly light on initial press?
@raisin392 жыл бұрын
@@JCCollinsRacing yes it does. Should I replace it with a soft rubber. I saw someone use an eraser stick.
@JCCollinsRacing2 жыл бұрын
@@raisin39 I would definitely recommend getting a more progressive damper similar to what I outlined in the video. It doesn't have to be that exact one, but something similar will really help the brake stiffness become more gradual as it is pressed. You will be able to judge your braking much easier with this.
@raisin392 жыл бұрын
@@JCCollinsRacing Thanks for leaving message about the breaks. I have another one.....one of the clamps jammed on the e G29. This clamp is tight won't lossen. I put wd40. I did a firmware up grade and that's when it got stuck. Thanks for your help.
@spacemonkey59 Жыл бұрын
Just bought a G920 and the brake pedal must off been designed by someone who hasn't ever used a brake pedal, the mods to correct cost about 10% of what I paid for the whole set up so I just set the clutch for left foot braking, if I would of known that the brake was useless I wouldn't of bought the gear shifter lol.
@JCCollinsRacing Жыл бұрын
Lol! The brake is rough initially. Luckily modding the g29 and g920 are identical. Even just removing the rubber block gives the brake pedal a much better feel.
@joshua99412 жыл бұрын
have converted my g29 pedals to hydraulic inverted, best thing reusing these crap pedals and making them into somewhat realistic feeling pressure based system
@JCCollinsRacing2 жыл бұрын
@Joshua that's awesome!
@joshua99412 жыл бұрын
@@JCCollinsRacing thankyou! great video by the way
@aidendavis3086 Жыл бұрын
Couldn't you just take off the pedal and unscrew the top where the black part meets the pedal? Save you taking the bottom off.
@JCCollinsRacing Жыл бұрын
Unfortunately, no. In order to get that black portion off, you have to unscrew the bottom. The black portion is one large piece that is directly connected to the bottom.
@juniormainmotor3 жыл бұрын
Then, how about the calibration after applying this mod? Your video is inspiring me to mod my pedals too~ 😁
@JCCollinsRacing3 жыл бұрын
@The Unsorry luckily there is no calibration needed. Since the pedals still technically measure braking force by distance traveled, each position of the pedal still gives the same reading. The spring and damper just gives you (the driver) a more realistic, progressive braking feel. You can still re-calibrate the pedals to your personal sensitivity and through each sim if you want. Trust me, you will not regret modding the brake pedal! 😁
@vulcan1449 Жыл бұрын
I'm slightly confused. Why would we want to make it even harder to press🤔. This new mod although it improves the progressive feel of the brakes, it looks like it makes it even harder to press the pedal to 100 percent. So isn't it going to be inconvenient for hard racing in Sims like ACC where we're having to mash the brakes very often? Or is it easier with this mod to press it to 100 percent than with the stock setup?
@JCCollinsRacing Жыл бұрын
Since the fell is more progressive, it feels more like real car where it is light in the beginning and stiffer as you compress it. The advantage is that the Sims brakes calibrations can be very sensitive and small inputs can make the sim think you are slamming on the brakes. Making it a bit harder to press will helps to modulate how sensitive the brake feels. Even with assisting your brake pressure and sensitivity in the sim, the G29 feels to light and has a hard stop with the stock setup, preventing you from getting the full breaking potential. This mod allows you to unlock the full potential.
@vulcan1449 Жыл бұрын
@@JCCollinsRacing I see...thanks for the reply. I think these mods are better suited if it's fixed on a rig rather than the floor so that we could use our force. I currently have mine placed against a wall (the back of my desk) but still, if I use all of my force to get to that 100% brake, it moves my desk slightly after a couple of laps 😅. Which is why I thought it would be inconvenient if it was even harder. Overall my braking is just not consistent with the stock setup. I saw some people just remove the stock rubber and presumably it makes it easier to press. But it may feel kinda off since Logitech has given a custom curve for the brake, intended to go along with the stock rubber. Any way we could program it to a linear curve would be nice.
@JCCollinsRacing Жыл бұрын
@@vulcan1449 that is true that the mod works better when on a rig, but it still works really good if you are using something like the Playseat Challenge.
@erikreznak Жыл бұрын
What can be done ,,safely,, to smooth up the braking? it feels stiffer.. and i have an ,,issue,, I push the brake to maximum.. but in the game it was braking around70% why
@JCCollinsRacing Жыл бұрын
@Erik Režňák try recalibrating your pedal set. You can do it through Logitech G-Hub and you may have to do it with each sim that you are running in the options menu.
@emeritoaugusto69533 жыл бұрын
Joder tío cojonudo.
@richmeier7 ай бұрын
Did you use any pre load washer for throttle as well?
@JCCollinsRacing7 ай бұрын
@richmeier yes. I used one of the thinner preload washers.
@richmeier7 ай бұрын
@@JCCollinsRacing thanks, and did you use any on the brake or just the yellow damper?
@JCCollinsRacing6 ай бұрын
@richmeier yes, I used one for the brake and clutch too. Sorry for the delay in my reply.
@cesarmaidana50163 жыл бұрын
The rubber that you take out?? Saludos!!!🇦🇷🇦🇷🇦🇷🇦🇷🇦🇷
@JCCollinsRacing3 жыл бұрын
@Cesar Maidana yes. There is a small rubber block inside of the brake pedal that is supposed to act as a damper, but it does not do a good job of giving the brake a progressive feel. The pedal just has a hard stop. At time of recording this video, I could not locate the original block that I removed and that is why I did not show it. I apologize for any confusion.
@timoxa5283 Жыл бұрын
i installed the yellow mod, but my computer only sees 60 percent of the entire length of the brake. can you help me?
@JCCollinsRacing Жыл бұрын
@Timoxa have you installed a stiffer spring with it? The damper may not be allowing the brake to travel the full distance. Originally, I had to redo putting the damper in the spring because it was getting kinked inside the spring. Also, ensure that you removed any black preload dampers that may or may not be inside the brake pedal. With the yellow damper in place, you will not need the black one.
@JCCollinsRacing Жыл бұрын
@Timoxa also, are you using G-Hub? You may have to recalibrate the brake pedal since the travel has changed.
@timoxa5283 Жыл бұрын
@@JCCollinsRacing Thank you
@lorantbenyak61163 жыл бұрын
Can u write the dimensions of the new spring ?
@JCCollinsRacing3 жыл бұрын
@Lorant Benyak the spring dimensions in cm are, length 6.35 x diameter 2.54, in mm they are length 63.5 x diameter 25.4, and in inches length 2.5 x diameter 1.0. I hope this helps!
@szn3130 Жыл бұрын
It Is a good mod or no?
@JCCollinsRacing Жыл бұрын
@szn3130 yes, it is a good mod. It definitely helps with brake feel and modulating the pedal better.
@WithSeb Жыл бұрын
40$ for the damper they are having a laugh
@Kripeld2 жыл бұрын
Good vid but actually...stop saying actually every 5 words lol