Loud home AIR VENTILATION SYSTEM ✅ Time to do MAINTENANCE AND CLEANING

Loud home AIR VENTILATION SYSTEM - Time to do MAINTENANCE AND CLEANING - At home VLOG
#HomeAirVentilation #FanMotorReplacement #FullCleaning #FanMotorBearings #ValloxDigitSE
How to perform a complete cleaning for the home air ventilation unit?
How to clean heat exchanger?
How often should the home ventilation unit be cleaned?
How to make the home air ventilation system quiet?
How do I remove the fan motor from the ventilation unit?
Does the fan motor need to be replaced?
How do I replace the fan motor bearings?
The home air ventilation system has been making an annoying noisy whistling sound.
An ventilation system is original from 2005.
Now is the time to do a complete cleaning of the air ventilation unit as well as the replacement of the fan motor bearings.
- A new fan cost 140.00 euros (210w - R2E140)
- Filter change notification
- It is time to do a complete cleaning of our home ventilation unit
- Sounds like at least one fan makes extra noise!
- Remove the microfilter and the two coarse filters
- Turn on the unit and listen to which fan makes the extra noise; Is it inlet or outlet fan?
- A useful tool for this: Noise stethoscope
- The input fan bearings needs to be replaced
- Remove the heat recovery cell
- Make sure there is no electricity in the device before going any further !!
- Disconnect the inlet fan rubber collar and the fan itself
- Disconnect the fan power cord
- Remove the fan motor rubber pad
- Also remove the outdoor air inlet fan
- Remove the preheater out of the way of cleaning
- Clearly it is time to clean up
- Check the water drain hole to make sure it is not blocked
- This fan motor is from 2005. I have already replaced the bearings here many years ago
- Replace the bearings again and clean the fan blades
- Remove the fan motor from the housing
- Remove the spacer from the front
- Remove the shaft bearing cover
- Remove the shaft locking ring and shims
- With the puller, remove the motor from the wing frame
- Remove the shaft bearings
- These bearings have done their part a while ago
- New bearings in place
- The second fan is from 2008
- Same cleaning for this fan as well
- The filters are first washed with dishwashing detergent and then rinsed in clean water separately
- Personally, I use coarse filters 2 or 3 times. These will wait for the next filter change
- This filter should be replaced once a year. Write the date in the filter
- And next all the parts back in place!
- Test whether the running noise of the ventilation unit is silenced
- It seems that the sound is even louder
- Replacing the bearings did not help in this case. Poor quality bearings?
- At this point, I will replace the completely new fan motor
- Disconnect the power connector from the old to the new one
- Ah!! The power connector still needs to be disconnected to get the cable through the board!
- Big difference in spinning sound
- The drain hose was clogged and this is the reason
- Replace the new drain hose
- The new drain hose is now in place and the lower guard will be put in place next
- One more thing! Resetting the service interval from the control panel
- The running sound of the ventilation was considerably silenced
DIY for
Noisy / loud / clamorous / vociferous
Home air ventilation system
Ventilation unit
Ventilation machine
Ventilator
Unit full cleaning
Cleaning ventilation unit
Clean filters
Heat recovery cell
Remove the preheater
loud fan motor
replace the new bearings for the fan motor
fan motor replacement
ilmanvaihtokone
kodin ilmanvaihto
ilmanvaihto
täydellinen puhdistus
puhaltimen moottori
moottorin laakerit
laakereiden vaihto
kovaääninen
VALLOX DIGIT SE
608Z
If you liked this video, press the LIKE BUTTON, SUBSCRIBE channel, leave COMMENTS and SHARE content!
By doing so, you will be able to support this KZbin-channel!
Thank you! I appreciate it! 👍
Have you already watched my previous videos of the home projects?
If not, check out the videos!
See whole SERIES form here:
• DIY's At Home - VLOG B...
Jani Voutilainen
You can follow me also in:
INSTAGRAM: / voutilainenjani
FACEBOOK: / jani.voutilainen
KZbin: / janivoutilainen
--
Thanks for Music:
Sports And Car Energetic Trap | GREVE by Alex-Productions | / @alexproductionsnocopy...
Music promoted by www.free-stock-music.com
Creative Commons Attribution 3.0 Unported License
creativecommons.org/licenses/...
and
Vercetti by jiglr | / jiglrmusic
Music promoted by www.free-stock-music.com
Creative Commons Attribution 3.0 Unported License
creativecommons.org/licenses/...

[@Sakura1]

Great video of bearing replacement. I didn't have the bearing puller last year. I ended up using some lithium grease. Which helped reduce noise. This year I will replace bearings. A new motor unit is too expensive. Is it possible to remove an old bearing without damaging it?

[@oliviacollier3310]

Hey! I'm from Family Handyman, and we saw one of your amazing videos. We'd love to share it with our fans! Send me a message for more info!