How did you get the deck so clean? was it skimmed? or sanded, great vid, doing the same process, total rebuild, 👍👍
@jupier3244 күн бұрын
"For motor N43: Cam of release bearing (A = 12mm) is on sliding surface of release lever" And for the n46b20 engines?
@antares884 күн бұрын
Kann man den auch mit inpa codieren?
@satti77754 күн бұрын
That is so helpful video could you please tell us how much it cost? And can u do it for me mine has same issue too I have bmw 116i 2005
@bigdeal874 күн бұрын
Im about to replace my timing chain 250t km, the crank seal has no leaks, is there any reason to change it ?
@eemuman6055 күн бұрын
Moro, onko järkeä tehdä vaihtoa vielä jos ääntä ei tosiaan vielä kuulu?
@Yeshuaschosen5 күн бұрын
My chickens and cats would fight over it!
@billsmith7566 күн бұрын
Hi Jani, did you find the fault? I also have a fault indicating the CCV in the rocker cover but I am not convinced the cover has a CCV! I say that as there is no resistance when blowing or sucking on the outlet. I tried this on the old cover and 2 new covers
@vitkubal2737 күн бұрын
Fixed. Thank you!
@v6cosworth1677 күн бұрын
did you have the block and head skimmed?
@millet-lp8cg8 күн бұрын
Very good job on showing all the steps you need to take it apart and fix the problem.
@Telstar_19 күн бұрын
Does anyone know about non return valves for the Vanos on a 2008 N43 318i engine? I've previously cleaned the Vanos solenoids at the front of the engine. But I've heard about non return valves having blocked filters causing hesitation, stalling and check engine light on other engines, and suspect I have this problem? Where are they and how to access? Any advice appreciated.
@piergeraci12 күн бұрын
Good Job. Info please: the Gasket Rings and the Caps for all, MOtor, Gear and Drive, can you provide the size?. The ones you mentioned Ithink are BMW parts Number....
@0223alan12 күн бұрын
hi. there Does BMW F20 (N13), HIGH OIL CONSUMPTION the key factor is the piston oil scrape rings design issue, not only just replace the valve stem seals?
@HB-wu4kg13 күн бұрын
kiitos etukäteen ja hienosta videosta. Kertoisitko? Saisiko lainattua jostakin BMW N13 ajoitus , lukitus työkalut? vai onko pakko ostaa?
@domkraggp994416 күн бұрын
By the way how is this diff holding uo after rebuild ?
@GUCIOman1918 күн бұрын
You dont change this green cable ? From mass
@abi3.05519 күн бұрын
Ich habe es noch nie gemacht. aber wenn er es kann, kann ich es bestimmt auch.
@artoalavuotunki723621 күн бұрын
Voiko ajaa pikku vaihteella ja hitaammin? Kun ei nyt voi motarilla ajaa 120kmh......
@AlbertoDefranchi22 күн бұрын
Have you found out what oil consumption was due to?
@freedom1463922 күн бұрын
Hey great video. Does it matter if one shock is oil pressure and the other gas?
@rolandgovender579124 күн бұрын
Thank you your video was a very helpful
@Axu_0228 күн бұрын
Kiitos videosta! Tilaan tuon työkalun ja mittaan N47D20C koneen tilanteen. Kilsoja on 344tkm ja merkintöjä ketjun vaihdosta ei ole, joten vähän jännittää :D
@aever685129 күн бұрын
Спасибо друг начну делать свой мотор буду пользоваться видео как инструкция руководство
@hvv90029 күн бұрын
Thank you.
@laurentbelmonte3068Ай бұрын
Everybody waiting answers but the guy doesn’t reply...i heve the same oil consumption problem. The replacement of valve stem seals didn’t solve the oil consumption problem. Sorry to not be able to help you...
@hamidgh3178Ай бұрын
Hi, i have a BMW E91 stationwagen Since two weeks ago I had a malfunction and read it and I have error code 29F5 catalyst speed syst 2 too small would you please give me more information? thank you
@abnerbecerra4975Ай бұрын
Excelent, what measures of torx and millimeter sockets did you use in your 118i?
@kestasradzevicius8672Ай бұрын
Do you need to do AFR adaptation after replacing pre or post cat lambda sensor?
@PoisonShot20Ай бұрын
The music is so annoying!
@jacekawtuch-rf4scАй бұрын
Hello, you have uploaded a great video, my r1150r works fine when cold, but after warming up it gets worse and worse and eventually goes out. After cooling, the situation repeats itself. What do you think it might be? Thank you and best regards.
@antxakАй бұрын
Very helpful, great tutorial. My INPA software doesnt offer the desulphination. What version of this program is shown in the video?
@advancetotabletop5328Ай бұрын
Glad to see your entire family (: working on the project!
@allmech_BMW_fault_findingАй бұрын
Beautiful looking channel and nice video. Hienoa!
@paweg4643Ай бұрын
Don't buy nox sensor from BMW. The continental nox board is lifetime. Just replace the probe. It is NGK NS11A. The colors of wires are the same. Good tip from Poland to cheaper repair.
@beautym321Ай бұрын
良い動画をありがとう、
@frankdoe3298Ай бұрын
Great video! You really helped me out with the pipe for the right rear brake. Pipes with rusted and stuck bolts need to be replaced. You cannot take any risk with brakes.
@domkraggp9944Ай бұрын
JUST WHAT I WAS LOOKING FOR !! have an e90 323 with a whining diff
@bigdeal87Ай бұрын
How did you lose the crank bolt only by locking with the flywheel pin ?!
@bigdeal874 күн бұрын
Please answer thanks
@bigdeal87Ай бұрын
Did you let the front frame just hang ? Only remove steering u joint ? Thanks
@thomascrown8973Ай бұрын
MSS60 not found on E93... What seems to be the problem?
@AncoraImparoPiperАй бұрын
Well built and designed to allow easy access to all levels.
@AncoraImparoPiperАй бұрын
Fantastic build. Quick and simple. Love the cats' first reactions on entering their new domain.
@AbdulHaq11901Ай бұрын
Can this fix my 2B05 nox sensor heating code? Thanks
@PazitAnimalWelfareАй бұрын
Nice job!
@betounivazo3452Ай бұрын
Hello friend, I have a problem with my mechanical BMW 114i 2014 N13 1.6 turbo engine. The car vibrates and has no power when driving, an unstable relationship. I changed the injectors, the pressure can pump, we tuned the car, new spark plugs, new coils and the problem remains the same. Have you ever experienced a similar problem?
@olivier7832Ай бұрын
Merci
@user-ws6fv7xt2u2 ай бұрын
Felicidades por. Compartir tus conocimientos son muy útiles grasias
@kimberlypaulson45452 ай бұрын
Such lucky cats and dog. Wonderful video.
@shadowboybass2 ай бұрын
in static will work or not ? i dont have the road for doing that .... i trie and when i reache 550°-600° lambdaset poit come down from 1.00 to 0.97-0.95 and then i cant go furthe because the small roar ... and then i lose temp 450-300 and lambda goes al 1.0 ... so is a shit in France whit small road ..ani idea hou can regenerate my Nox catalyst ?