Mine keeps saying errors on p02 what is this meaning plus I have no throttle power at all
@MrAgben18 күн бұрын
Can u set the display to auto-on when turning the battery switch on?
@theebikeguy385218 күн бұрын
@@MrAgben You would have to get into the display. And bypass the power switch solder it on the board to where it comes on immediately. Not a easy task.
@beatrixujj1447Күн бұрын
This was sooo incredibly helpful, thank you so much. Although I'm still looking for what the person I bought it from has shown me; apparently he was able to set the maximum speed in each PAS "level" but I cannot remember for the life of me how he did that. Is that actually feasible?
Hello I really need to know how to remove the speed limiter on E-Mountainbike MONTIS EM 1726 by FISCHER with bafang display. Can u tell me how or if its possible? The e bike is really fast but its limited at 25-27kmh
@theebikeguy3852Ай бұрын
Without knowing what display you have, it's hard to say. Never heard of it, so I'm guessing that must be an Amazon bike. On the back of the display, there should be a number embossed into the plastic or a sticker on it that will give you a number like KT - 153.
@acmajeАй бұрын
@@theebikeguy3852 The display is Bafang DP C10
@anoublezbie29 күн бұрын
Hello I have a ouxi h9 and I put this one on it but it doesn’t accelerate and it also goes out from itself. Do you know what to do? also when I put it on the fatbike the cables were different. The one on my fatbike is xmdy and the one that I ordered is xsd. Please help me
@theebikeguy385229 күн бұрын
@anoublezbie Most LCD displays & controllers. Are programmed together if you try to mismatch them it ma cause not to run correctly. Even burn up the LCD or controller. Not all are compatible with each other.
@anoublezbie28 күн бұрын
@@theebikeguy3852 hi. What does error e008 mean on a h6c display? And what happens if I ride with it
@theebikeguy385228 күн бұрын
@@anoublezbie Not a lot of information out on that display at this time. However, arcode 08 usually indicates either a faulty throttle or a hall sensor issue in most cases. I suggest unplugging the LCD display as well as the throttle. Checking the pins if everything looks good. Reconnect these wires in most cases, if they're not quick. Disconnect and these are high go connectors. They will have Arrows to lineup and snap back in place. In one case I even seen This code comes up because the tire size was programmed incorrectly.
@anoublezbie28 күн бұрын
@@theebikeguy3852 oke
@shaunwong95213 ай бұрын
Thanks for the video I got an m5 LCD screen and it is reading an error code. E-010 I've read a few different things but aren't sure. Thanks
@theebikeguy38523 ай бұрын
Most likley a communication receive from controller to the LCD display...if this is a Hygo Conecter plug, unplug the LCD Display, make sure no pins are bent or any Corrosion is present. If everything looks good line, the 2 arrows up on each side of the high go connector press firmly to reconnected. See, if that clears the code. If not, you may have to buy a new l. C. D display.
@williamvan90929 күн бұрын
Thanks for letting us know looks like I better get a new lcd mine is brand new with the motor kit 😭 😭 😭 😭 @@theebikeguy3852
@valentijnbroeksma8386Ай бұрын
Hey i have the same display as you, but mine won't give any power and the speedometer isn't accurate do you maybe know what to do? My bike is a Ouxi V8
@theebikeguy3852Ай бұрын
First try disconnecting both of you Breaking inhbiters. If you do not have power and if you had went into the settings and messed with anything that would cause it not to run, it could also throw the battery to read inaccurate or if you mess with the magnet numbers you could burn up to display or the controller. If you haven't done any other hat and the speed ometer is just slightly off the only thing you would have to do is adjust the wheel size to change the speed As far as it. Not working usually there is an Error code..... Do you have pedal assist but not throttle? If so, most likely your throttle is defective.
@williamvan90929 күн бұрын
Thanks I'm having all these problems with my kit thanks guys
@AyoubBenhaddi-sr7jdАй бұрын
Can i make it so that when i press something my speedlimit goed back to 25 km/h?
@theebikeguy3852Ай бұрын
If you're referring to the top speed. Go to PZ rotate. If it is set at 100%. Try 80% and see how that goes.
@paulohenriquecarvalho85273 ай бұрын
Qual a senha para desbloquear e poder aumentar velocidade para 100?
@Km05772 ай бұрын
His display says “manual” . Does that mean it is pedal only? Mine says this and it is stuck there. Throttle won’t work, or pedal assist. Someone help
@theebikeguy38522 ай бұрын
You might try to charge the setting on P10 This will switch peddle assest and throttle, Also, you may try disconnecting the LCD display from the controller.Plugging it back in also disconnect the motor from the controller and plug it back in. If it does not work it may have a partly faulty controller or motor if it does not work, Do you have any air codes on the screen? I can explain to you how to run a test on the motor to find out if it is the problem if that does not work. For some weird reason, I have seen some of these say manual on the screen. Others do not have anything there and they work fine so it's kind of weird honestly I really don't know what that is. But in the past it is not affected. Any electric bike that I worked on with this display.
@FatiguedratАй бұрын
Did you get an akez bike by chance throttle is disconnected on shipment @km0577
@theebikeguy3852Ай бұрын
@asahogreve1331 I'm a 12 yr. Ebike Tec. I don't have any ebikes just a Wolf king GT PRO AND ordered a Nami
@jamesishere66303 ай бұрын
my only goes to 03p on my dyu any idea why?
@theebikeguy38523 ай бұрын
Different Companies have. the displays programmed in a different manner.
@jamesishere66303 ай бұрын
@@theebikeguy3852 ya DYu sucks
@theebikeguy38523 ай бұрын
@jamesishere6630 lol, ya get what you pay for, but for the price it's decent.
@anoublezbie29 күн бұрын
Hello
@timgerdes95414 ай бұрын
How to factory reset???
@theebikeguy38523 ай бұрын
Go to 16P. Press The minus button for approximately 5 seconds.I believe this screen We'll flash 000. Then press plus and money said the same time To get out of the settings. Power it off and back on it should reset
@robertpurcell78624 ай бұрын
My settings won't change any ideas why
@theebikeguy38524 ай бұрын
Never seen one that could not if you hold the up and down button at the same time for about 5 sec. Should go into p settings.
@robertpurcell78624 ай бұрын
I've done all that I can get in but when I go to next setting the numbers won't change up or down? I have to replace it I think it maybe faulty nothing works the other bike has no problem
@verily12214 ай бұрын
My amps goes up to 31 amps.
@verily12214 ай бұрын
Was factory default @22.
@verily12214 ай бұрын
And as far as helping your battery last longer, no the battery has it's own cut off settings in it's BMS which over rides anything the bike controller tries to do.