Magpul PRS Gen. 3 Stock. Review, Install and Adjustments.

[@kellywinford2573]

The world needs more straight forward videos like this. Thank you!

[@davestrohmeyer-saddleupsho8009]

Thanks for watching.

[@nohandle257]

Thank you. I needed this. I bought this Magpul stock for my CMMG 6.5 Grendel lower that came with an Ace butt stock. I went to change them out a couple weeks ago but when I slipped the Ace stock back ( very tight ) and saw that little spring I quit. I was not sure about that spring. I knew what it was but didn't have the confidence to continue. Now I do. Just hoping I can do the job without kinking that spring. That rear screw has a hole for venting that is important might be mentioned.

[@davestrohmeyer-saddleupsho8009]

Thanks for watching and for your comment

[@nohandle257]

@@davestrohmeyer-saddleupsho8009 30 minutes later and Got her done. Almost easy peasy. The little spring was no problem. But the magpul supplied rear screw was a scoche too large so I just used the Ace stock cap screw. It isn't vented like the magpul slotted screw but evidently that is not necessary as the rifle was fine without a vented screw. Also, for others, don't unscrew the rubber buttplate screws too far as then you will lose the 'nut' that goes in a slot within the stock itself. If you do that you will have to have the gun sticking down and straight up to get them aligned again. Not a total pain and doable. I know. My ball head and clamp will do that as the ball receiver has a slot allowing it.

[@cw2a]

Mornin Dave! Re watching. ( watched & commented from my old -deleted account) Anyhow just got this stock ( used from friend) & making quick video.

[@davestrohmeyer-saddleupsho8009]

I'll be sure to watch all your videos. Always educational content.

[@donaldsudnick2003]

Great video,Dave. Thanks for recording from different angles during this installation.

[@davestrohmeyer-saddleupsho8009]

Thank you for the kind words and for watching.

[@zachearley1906]

I was on the fence about buying one of these. But after watching this video, you have convinced me to make the purchase.

[@davestrohmeyer-saddleupsho8009]

Best of luck to you. They make a lighter weight version now and less expensive too.

[@davidtruglow7381]

Nice straight forward installation. Was going for a 6 ARC but decided to build a 6.5 Grendel and use a rifle buffer tube. This vid is better than the instructions.

[@davestrohmeyer-saddleupsho8009]

Thanks for your comment and for watching.

[@giuseppecasbarra7131]

Congratulations, finally a concrete review, without those endless strings of useless adjectives. Really interesting. Best wishes.

[@davestrohmeyer-saddleupsho8009]

Thanks for watching and the kind words here.

[@ThePaulv12]

That was actually a really good vid. I find it difficult to follow any vid that assumes basic knowledge because not everyone has basic knowledge; which is why we're seeking out basic knowledge vids. I'm trying to piece together and cost a chassis system and this vid certainly aided me in that. Despite the high cost of this buttstock, I'm going to hang the expense and buy it.

[@davestrohmeyer-saddleupsho8009]

Thanks for watching.

[@janicejohnson1334]

Thank you for an XCLNT vid . . . Hubby just bought this PRC to install on his POF 308 20" Piston ... will post more when installed

[@davestrohmeyer-saddleupsho8009]

Glad it helped. Thanks for your kind comment.

[@tylerwhitsell]

I love your build. I never get to see 6mm Arc builds. Great video! I was worried that the stock would be flimsy but it looks really sturdy here. I think I'll be trying one of these on my grendel soon.

[@davestrohmeyer-saddleupsho8009]

Thanks for watching and for your kind comments.

[@JDAN.]

Very helpful video Dave, thank you. I'm building a 20" Compass Lake Engineering Douglas .870 gba .223 Wylde coyote hunting rifle myself. New to shooting at or over 100 yards so I'm having to learn a lot at once with this build. Can't wait to take it to the range and learn. God bless!

[@davestrohmeyer-saddleupsho8009]

Best wishes on your progress.

[@PracticalAccuracy]

Good Review. I'm thinking of getting one for my long range AR set up.

[@davestrohmeyer-saddleupsho8009]

They have a newer version that is lighter and less expensive now.

[@MrPatrickjsmithsr]

Very good video no bs just great basic info thanks

[@davestrohmeyer-saddleupsho8009]

Thanks for your comment and for watching.

[@williamcollins3565]

Thank you for your video. I just received a PRS and the instructions, apparently not the ones you received, were totally inadequate. You have cleared up a lot of problems for me.

[@davestrohmeyer-saddleupsho8009]

Glad I could help. Thanks for watching and commenting.

[@jeffreymortensen1666]

Thanks for the great video and experience explained in this stock.

[@davestrohmeyer-saddleupsho8009]

Thanks for watching.

[@klous671]

Very nice! A buddy of mine has one, and they are as solid as they come. It sure made that rifle look even better than it already did.

[@davestrohmeyer-saddleupsho8009]

Thanks for watching and your comment.

[@antpoepoe6750]

About to purchase that stock , then I came across your video , thanks sir for creating this content 🤙👍

[@davestrohmeyer-saddleupsho8009]

Hope it works well for you. Thanks for watching.

[@flubbernuget]

Thank you for posting this video. It was really helpful.

[@davestrohmeyer-saddleupsho8009]

Thanks for watching

[@crimbullet]

Love your rifle, the setup, and the old fashion sling!

[@davestrohmeyer-saddleupsho8009]

Thanks for watching.

[@anonymouscitizen2732]

A very fine tutorial. Thank you for taking the time.

[@davestrohmeyer-saddleupsho8009]

Thanks for the kind words and thanks for watching.

[@NikoliFerra]

Thanks for the detailed review and installation. I like your setup!

[@davestrohmeyer-saddleupsho8009]

Thanks for watching

[@rustynut1967]

Never a boring moment in your videos.👍

[@davestrohmeyer-saddleupsho8009]

Thanks for the kind words.

[@blipcat3382]

Thanks, for the info and video...........switching to a gen3 myself.

[@davestrohmeyer-saddleupsho8009]

Thanks for watching.

[@airbornevetrando]

Thank you for showing this install

[@davestrohmeyer-saddleupsho8009]

Thanks for watching.

[@ChuckinTV]

That aughta bring those groups in even tighter. Having the proper length of pull and eye alignment with the scope is key to consistent accuracy. Looking forward to you range results

[@davestrohmeyer-saddleupsho8009]

Yes...But this is a swapped lower off of my 5.56. The old stock on it was for it. The 6mm ARC needed a new stock for all the reasons you stated.

[@APlife764]

Thanks for your time presenting this video

[@davestrohmeyer-saddleupsho8009]

Thanks for watching.

[@RT2Do]

Thank you sir! Just want I need to add to my wish list for a CMMG Endeavor AR10. I liked the video!

[@davestrohmeyer-saddleupsho8009]

Best wishes to you and your rifle.

[@lifesaver818able]

Great review!! But I wish Magpul would bring back the gen2

[@davestrohmeyer-saddleupsho8009]

Thanks for watching.

[@shanegibb997]

Excellent video Dave ...

[@davestrohmeyer-saddleupsho8009]

Many thanks!

[@fightmilk8613]

Thanks Dave!

[@davestrohmeyer-saddleupsho8009]

Thanks for watching.

[@williamdaisley1373]

Good job! Very helpful.

[@davestrohmeyer-saddleupsho8009]

Thanks for the kind words and for watching.

[@jeffslosson1095]

Thanks for much and God Bless!

[@davestrohmeyer-saddleupsho8009]

Thanks for watchin.

[@csenior10]

Beautiful looking rifle

[@leonardboufford282]

I have a gen 1. Great stock.

[@davestrohmeyer-saddleupsho8009]

Thanks for watching.

[@Anduin-oy5ij]

Great video. Thanks for making it.

[@davestrohmeyer-saddleupsho8009]

Thanks for the kind words and for watching.

[@warwickdennis4114]

Very helpful

[@davestrohmeyer-saddleupsho8009]

Thanks for watching.

[@luvtahandload7692]

Thumbs up, Dave! Nice gun cabinet. Did you add the hooks that are holding the lower? Never seen a cabinet like that. Are they antler tips or grizzly bear claws? 😂 I like that idea of using an old belt for a sling. I suppose you had to trim it down to fit the swivel loops. (Upper, I meant)

[@davestrohmeyer-saddleupsho8009]

They are Muley antler double eye guards, just wide enough to hold the upper. Thanks for question.

[@briondionetoler]

It looks good

[@janicejohnson1334]

OK . . . Just ordered ( on line ) ... Ordered AERO 308 Rifle Length Reciever Exten . . . Ordered AERO 308 Rifle Buffer Spring . . . Ordered AERO 308 Rifle Buffer . . . I have extra castle nuts & end plates . . . So am I good to go ? . . . Is there anythig else I need to install the MAGPUL PRS Gen 3 stock . . . ? Monday ( 08.29.22 ) XCLNT video . . . I wish I knew more about guns . . . Learning as I go

[@davestrohmeyer-saddleupsho8009]

Sounds like you are on the right track. I suggest you contact Magpul directly with your questions. The Magpul PRS gen 3 comes with everything you need, assuming you are replaceing an existing stock. Thanks for your questions and for watching.

[@janicejohnson1334]

@@davestrohmeyer-saddleupsho8009 I have a sripped lower . . . I bought MAGPUL not knowing I needed other parts ... I did reach out to MAGPUL . . . No reply . . . Kitchen table covered in parts . . . Need to keep moving forward . . . XCLNT video . . . Thank you for your time and reply back . . .

[@davestrohmeyer-saddleupsho8009]

@@janicejohnson1334 Stripped lower does require parts as well as assembly tools, such as punches, small screw driver and others. Suggest you watch lower assembly vids on KZbin and or seek assistance from a qualified source especially with the fire control (trigger) group. It is a great learning experience and congrats on taking on the tasks.

[@jstone9462]

This was great. Thanks

[@davestrohmeyer-saddleupsho8009]

Thanks for watching.

[@RickNethery]

Neat looking stock brother 👍

[@davestrohmeyer-saddleupsho8009]

Thanks Rick...I hope you aren't floating away in East Texas...Heard it is raining pretty hard.

[@RickNethery]

@@davestrohmeyer-saddleupsho8009 You're welcome brother, it's rained every day, lots of people got flooded and some roads washed out but we are fine. It's definitely too wet to mow.

[@wendigo6591]

Well it’s official, I’m getting one for the 450 bushmaster

[@davestrohmeyer-saddleupsho8009]

Thanks for watching and thanks for your comment.

[@alejandrocabrera3380]

I heard those add some extra weight to the rifle, any idea how much it could be? Great video, thank you

[@davestrohmeyer-saddleupsho8009]

Depends on what stock you already have and how much it weighs. In my case it added about 16 ounces.

[@alejandrocabrera3380]

@@davestrohmeyer-saddleupsho8009 I have a regular A5 on my ar 10. Thank you for the quick response

[@racoming1035]

I found the PRS too long. I'm short, my LOP is 12.5". The shortest this goes is about 14".

[@davestrohmeyer-saddleupsho8009]

Sorry it didn't work well for you. But I am sure you can recoup some of your money @ Gunbroker auction site.

[@janicejohnson1334]

What size buffer tube do I need to purchase ? I have a POF 308 stripped lower ..... Do I Need buffer spring? . . . Do I need Buffer ... What size . . . How Long . . . I'm new to this . . . Looks like I need more parts . . . Please help . . . Thank you ( 08.29.22 )

[@davestrohmeyer-saddleupsho8009]

See the reply to your second comment.

[@davepayne2024]

Excellent

[@davestrohmeyer-saddleupsho8009]

Thanks.

[@rodyoakum1194]

Thanks For Video

[@davestrohmeyer-saddleupsho8009]

Your welcome. Thanks for watching.

[@katashi222]

Well done!!!💯👍🍺

[@davestrohmeyer-saddleupsho8009]

Thanks for watching.

[@zivick]

Anyone have any issues with that rear screw with the drain hole in it. Mine won't thread at all it just spins in there. M&P10

[@danemarley2866]

How High can you raise the cheek rest?

[@davestrohmeyer-saddleupsho8009]

1 inch

[@briondionetoler]

Cant eait install mine with my AR 10

[@davestrohmeyer-saddleupsho8009]

Best wishes for you and your rifle.

[@jacontreras04]

Well done!! Good information, thanks !!

[@davestrohmeyer-saddleupsho8009]

Thanks for watching