Make A Filling Station For A PCP Airgun Or Paintball Gun & Test It.

See this excellent low cost pneumatic filling station one can buy, assemble and test for a pcp airgun or paintball gun. SEE LINKS BELOW:-
0.5L Liter Aluminum Tank Air Bottle -- goo.gl/RBj9Vx
Stainless 1/8 BSPP Quick Release Hexagonal Coupler with 3 plugs -- goo.gl/qHXsJY
Paintball CO2 Adapter Compress Air Regulators Fill Station Remote On/Off With 3000PSI Gauge -- goo.gl/wvM5Cj
Paintball CO2 Adapter Air Regulator Fill Station Remote On Off 3000psi Gauge -- goo.gl/xEhkii
0.38L 5/8"-18UNF Aluminum Tank Air Cyclinder Bottle 3000 PSI -- goo.gl/FM2zds
1/8 inch BSP Stainless Steel Male Plug Quick Head Connector -- goo.gl/G9fRhy
Paintball PCP SCBA Fill Station Charging Adapter -- goo.gl/rjb7mQ

[@SteveJordan]

facebook.com/steve.jordan.3766952

[@DaithiDONKEYBIKE]

Absolutely excellent tutorial Steve, I'll be using most of your suggestions on a Brewing carbonation project using CalGas tanks with c-10 outlets.

[@airgundestruction2405]

great video very detailed. I'm making one I already have a few of these parts. cheers from California

[@tinkermouse-scottrussell3738]

Nice Steve, I use mine to work my finish and pin nailer no air line to move through the house works great. From Elliot Lake Ontario Canada.

[@davidstorton910]

That mate was outstanding and well presented .... Thanks

[@da33ie]

Ive played n replayed this vid for a while now! After studying it...i plucked up the bottle (0.8ltr) lol...to build one to your spec. Managed to get all the components inc relief valve , n built me one of my own!

[@OneWildTurkey]

One very important thing to remember is that ptfe tape is NOT a sealant. It's a lubricant. It just makes it easier to seat the different components that perform the sealing. Using too much tape can prevent getting a good seal.

[@thetraindriver01]

Absolutely brilliant video Steve, thank you 👏👏

[@corycampbell1013]

Very well done,thank you so much

[@moonolyth]

Subscribed.... grate video !! what more would be needed to add an air coupling for filling tires and so forth. Id like to make a multi-use tank system for air guns, filling tires in the filed soda pop bubbles, etc. Thanks, Much !!!

[@johnibbertson2960]

steve great job great when you know what to buy,steve what size thread is on output regulator and which type bsp etc ?thanks john.

[@airgundestruction2405]

I think instead of the 3way and the bleed valve You can just add a slide check . beautiful I'm exited. because fill stations are expensive

[@Abe8816]

I can’t find the high pressure tee fitting, can you give me a link for it

[@homerlapier8441]

I was a pipe fitter in a paper mill for 34 yrs and we used ptfe Teflon tape exclusively, the manufacturer had written right on the dispenser to use only 1 wrap of Teflon tape in the direction of threads. Not wrap after wrap

[@WW5RM]

Technical 1 wrap wont stay on. It needs to overlap. Plus ive seen numerous times even 2 wraps not seal off from steel to aluminum. Steel to steel, yeah 2 is enough.

[@OneWildTurkey]

There are several different types pf ptfe tape which have different applications and use requirements. Water, LPA and HPA can use the same type, but there is another one in particular for LPG which is noticeably thicker. Also, different manufacturers have different instructions. On top of those there are also building codes and safety organizations with even more details.

[@shaneweightman]

Very good thanks very much shane uk 🇬🇧

[@jasonstanley7949]

Fantastic video sir!

[@rogeliogerona8745]

Mr. Jordan I saw your video regarding filling station, can you give me all the link of complete parts needed or part number. I will try to order to local online store here in the Philippines.

[@shockwave1952]

What was the output pressure rating on your 4500 PSI regulator. Is it set at 800 PSI ?

[@WaschyNumber1]

Wher can I get the safety valve burst discs, that can be putt in the housing, this brass looking discs in different psi ratings, I find it a waste to buy the complete burst disc housings and they are not cheap.

[@joekelly9369]

awesome tutorial steve , iv learnt a lot , booOOOOoom 😨

[@WaschyNumber1]

Can I use any Hydraulic bsp fittings for 4500psi bottles?

[@leskrout613]

Right you need an output of 3000psi to fill. Amazon sells 4500 PSI regulator with 1600-3000psi adjustable output. Otherwise great video and thanks for sharing.

[@alsdisco]

Do you sell these made up I would like one for a game phox I been looking on eBay but would like one already made thanks

[@_Auroswim._.Ocean_Swimming]

Can you adapt it for snorkelling?

[@tlcpg8894]

Hi Mr. Jordan, Will all these parts fit a Benjamin Marauder Pistol or would I need different parts? Thanks for your help.

[@ke6ziu]

What about that T coupler?

[@stevemunn7609]

How many times can you fill your gun with that bottle before refilling.

[@abonfrere]

Great video, roaming the internet in search of the on/off valve but with no luck. At least not one that is capable of handling 3000PSI output. Can you add the link ones more? Curious to see the rating on that valve. Please give a reply

[@SteveJordan]

Hi thanks. I will see if I can find the sites with the valve. I can't remember offhand where I bought it now, but will see if it's still available. Regards Steve

[@WaschyNumber1]

Wher can I get cheap ptfe or delrin seal washers, some sick company's want 1£ for 1pc.

[@zulgenius609]

Can we fills the tank using common 2HP air compressor? I saw you use that bycicle pump, how you managed to get that 1000psi? Sorry for asking. I'm not good in this knowledge. Thank you

[@sweetleaf7751]

That is not a bike pump, i is a PCP high pressure hand pump.

[@MikeDean01]

Great video. Do you have a link for the 1/8 pressure relief valve? Thanks.

[@SteveJordan]

I can't find the company that I bought them from now. It was a UK company that is all I know. Someone else on here may know?

[@MikeDean01]

@@SteveJordan thanks for the quick reply Steve.

[@leenorris2862]

Can u buy 05l already made up, if id buy one off you

[@kikzb643]

how much did u spen on this one.. i need one.

[@WW5RM]

Do you have a link for the relief valve? A small needle valve should work but i like that one better.

[@SteveJordan]

Hi, It was a long time ago. I can't actually remember where I got it. I will have a look at the assembly later and see if I can find it.

[@WW5RM]

@@SteveJordan thanks

[@montanabush2294]

nice video like it only one problem is regulator only puts out 800 psi not good if ya need 2800 psi to fill gun with

[@SteveJordan]

No... the regulator dial is x1000. I use these to fill PCP air rifles.

[@sfzx54]

Steve, Montanabush is posing a valid question. Just because the gauge says 1000 PSI doesn't mean you get 1000 PSI if the regulator is set to 800 PSI. In the info for the .5 L bottle with regulator it says the reg is set at 800 PSI. How are you getting 3000 psi to air up your guns or even 2800 if that is your preferred fill to point? Did you alter the reg on the bottle to achieve your desired fill level by changing the shimming internally in the reg?

[@julesnormand6850]

You can buy à regulator with 2200 or 2800 psi out pressure

[@Abe8816]

I can’t find the tee fitting in the description you have, please respond. Thank you

[@SteveJordan]

Look for a 1/8" BSP three way fitting on eBay. That's what I did. Regards Steve

[@Abe8816]

@@SteveJordan thank you and have a happy new year to you and your family

[@GiovanniGiorgo]

Steve, thank you for this video!! Where did you get the pressure release valve/button on top of the tee?? I can't find one anywhere! Thanks!

[@SteveJordan]

I bought mine on eBay but I haven't seen the release valve since. The three way adaptors are on eBay though.

[@GiovanniGiorgo]

@@SteveJordan I've been scouring everywhere and haven't seen them either. That's the only piece that I can't find. The unicorn. I've made a makeshift release, but it's not the most safe. The journey continues.

[@zahrahamidian820]

Do you think the springer airgun we can modify it to PCP rifle. If yes how . Thank you from Toronto

[@MattysWorkshop]

Very compact units Steve

[@shanek6582]

mat johnstone that’s what she said ...

[@surreallife777]

I’m not sure I understand. Why do some 300 bar 4L air tanks cost $200 and why do some cost $500? Are the cheaper ones scuba tanks?

[@Brendan9300]

The part that is put on the paintball tank has a small hole dose it leak from there???

[@SteveJordan]

No it doesn't leak.

[@Brendan9300]

@@SteveJordan ok so whys there a hole there

[@SteveJordan]

@@Brendan9300 I think you maybe looking at a grub screw socket. Part of the fixture and how it is made. Regards Steve

[@Brendan9300]

Yeah found you find me a link for one

[@andresvidalpiedra1568]

Hello how many times can the PCP be filled from 2000 to 3000 PSI with that 0.5 liter bottle, Best regards

[@elcompamartinez2647]

Have you found out yet?? (1-18- 2023)

[@leenorris2862]

I want one

[@pelucheune271]

Hello sir how are you ? Can you please help me and tel me everything a got to by for make thé same thing you did please. Can i make one more powerful so i can shot at100feet minimum. Thanks you. Sorry my english is very bad 😂

[@ke6ziu]

I bought one off of eBay for US$225... a little less than 175 quid...

[@vlhruaia..5619]

Excilence tutorial but mr.? Im not understand 🤣

[@muttugoraguddi1576]

Sar amounts

[@SteveJordan]

NOTE:- I ONLY USE MY AIRGUNS FOR FIELD TARGET SHOOTING & ALWAYS ADHERE TO THE UK LAW FOR THEIR USE. SEE LINKS BELOW WITH VARIOUS OPTIONS:- 0.5L Liter Aluminum Tank Air Bottle -- goo.gl/RBj9Vx Paintball Stainless Steel Braided High Pressure Air Fill Hose -- goo.gl/6uZuca Stainless 1/8 BSPP Quick Release Hexagonal Coupler with 3 plugs -- goo.gl/qHXsJY Paintball CO2 Adapter Compress Air Regulators Fill Station Remote On/Off With 3000PSI Gauge -- goo.gl/wvM5Cj Paintball CO2 Adapter Air Regulator Fill Station Remote On Off 3000psi Gauge -- goo.gl/xEhkii 0.38L 5/8"-18UNF Aluminum Tank Air Cyclinder Bottle 3000 PSI -- goo.gl/FM2zds 1/8 inch BSP Stainless Steel Male Plug Quick Head Connector -- goo.gl/G9fRhy Paintball PCP SCBA Fill Station Charging Adapter -- goo.gl/rjb7mQ

[@mattomamato]

I need the regulator press realease presure

[@wallacemichael5354]

Lol 200 bahhhr