WOW! Amazing DIY Giant Robot Car at Home - PART 1

Hello Friends, in this video i will show How To Make a very Big robot car for controller Arduino , raspberry pi , Jetson Nano AI robot car or smart car For practical application
DIY Arduino robot car / smart car
DIY Raspberry pi robot car
Wheel : 10 inch
size : 80cm x 56 cm
Motor : DC Motor Gear 250watt 24Amp 310 rpm
PART2 - • DIY Giant Robot Car ...
::::::::::: SUPPORT CHANNEL ::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::
Please Donate To Help Me Afford New Equipment And Software To Make My Videos More : goo.gl/1m8Dg2
Don't forget to subscribe!
Song: MBB - Beach (Vlog No Copyright Music)
Music provided by Vlog No Copyright Music.
Video Link: • MBB - Beach (Vlog No C...

[@Narendra25567]

To determine the load capacity of a DC motor, we need to consider several factors, including: 1. Motor power (250W) 2. Current (24A) 3. Speed (310 RPM) 4. Gear ratio (not specified, assuming 1:1 for simplicity) A general rule of thumb for DC motors is to use the following formula: Load capacity (in kg) ≈ (Motor power × 1000) / (Speed × Gear ratio) Plugging in the values, we get: Load capacity ≈ (250W × 1000) / (310 RPM × 1) Load capacity ≈ 806.45 kg However, this is a rough estimate and doesn't take into account factors like: - Friction - Inertia - Motor efficiency - Gearbox efficiency (if applicable) To be more accurate, let's consider a safety factor of 0.5 to 0.7 (depending on the application). This reduces the estimated load capacity to: Load capacity ≈ 403.22 kg to 564.51 kg So, the DC motor can likely handle a load of around 400-560 kg (880-1234 lbs), depending on the specific application and conditions. Keep in mind that this is still an estimate, and actual performance may vary. Please provide more details about your project, such as the gearbox ratio, wheel diameter, and application, for a more precise calculation.

[@mosta5]

Nice idea . But it's missing shock absorber . It's very important to achieve stability

[@ziyadkhouad8120]

do you have 3d design or something can help me to design this please and thanks for the video :

[@Narendra25567]

Use karke bhi dikha dete🙂

[@anjv10]

Nice project well done 👍 it's much better if you can provide the details of the parts used in the description

[@Narendra25567]

How much weight can it Lift?

[@temyraverdana6421]

Good job, I like it. I have only a trouble about the position of steering connecting rod. In your design you have differen position of rod-end bearing (tie rods) min. 5:00 to 5:30, in this manner when you turn left or right, the angle of each weel is different each other. I think it is better connect at the same point the two rod-end bearing (pitman arm). Go on you are in the right way.

[@MakerTutor101]

Thank you very much, very helpful advice to me.

[@redfields5070]

I get all my designing right on the first try too.

[@cryptoworldgames]

Why do you not drive it?

[@FRESNEL_COOKING_SOLAR_OVENS24]

Robots should be driven by one motor on each wheel. Not by axle. You will have usage on the tyres like that. At each turn, you will scratch the ground with those solid wheels.

[@fedemon76]

Hello, very nice job, I have some questions: - Aluminium bars size is 20x20 or 40x40? - Wheel axle is 16 or 20mm? - did you pierce the pipe to put the flange screw through on the back axle? - Did you try on beach sand, it worked? - Whic material did you use to make the pulley? Thank you

[@infected7258]

I got motivated by a 6 wheeled Amphibious ATV I saw and I want to build something like that, where it can drive on land and maybe float on water as well

[@aimanzainul3065]

can i know what name of part that attach alluminium and tyre

[@theoquanzymedia9039]

Can u show me how to code arduino

[@emeraldbey_]

Please tyre kink in description

[@mirzamujammil8445]

From where i can buy that Wheel

[@Iezzam19]

Excuse me how to make this controller or do you have video to make this project have controller

[@bdanyluk]

I was literally going to make something almost exactly identical to this ! Thanks!

[@Narendra25567]

How to make it line following?

[@adilfarooq1430]

Hi, can you send the link of motor where can buy it?

[@SwapnilExperiment8123]

Wheels link plz

[@netturijishnu4108]

How much does this whole set costs?

[@djzatka]

Steering design is worst

[@KarlHeinzErdmann]

I like it, good idea!👍👏

[@MakerTutor101]

Thank so much

[@garrettsredwhiteblue4772]

Can you build a fly in car

[@Sumayyacollection05]

Are you want to make it a remotely accessible car

[@MakerTutor101]

Yes And for Jetson Nano robot car

[@Sumayyacollection05]

@@MakerTutor101 wow

[@arpitshrimankar7787]

@@MakerTutor101 awaiting for jetson robot car

[@o_p_gamer9603]

How can Buy that whill

[@falkgerbig7787]

Don't forget the timing belt cover.

[@MakerTutor101]

Ok , Thanks so much

[@semionmorozov5359]

Круто! Молодец!)))

[@dronefootage2778]

the reason why this video didn't get many views is the music, it's pretty bad