Interesting design! I built similar but made a U shaped part that holds the rings and bearings (brass/Teflon in my case) which allows the rings to be opened for removal of the OTA or rotating the OTA easily. I used a lazy Susan bearing to replace the record which turns better than my record allowed. I inserted a tiny 1/4" thrust bearing at the top of the center pivot which also helped the smooth operation. Fun stuff to play with.
@billkaroly Жыл бұрын
Nicely done.
@champifun23 жыл бұрын
Very well done! Where I can find / buy the blueprint?
@PuddintameXYZ3 жыл бұрын
Seconded
@drewcarruthers7113 жыл бұрын
Seconded again
@PuddintameXYZ3 жыл бұрын
@@drewcarruthers711 See other comment by myself. He doesn't have the plans anymore
@drewcarruthers7113 жыл бұрын
@@PuddintameXYZ I read and know that - no harm asking again! see my others comments
@PuddintameXYZ3 жыл бұрын
@@drewcarruthers711 👍
@ManishFrenchStudio3 жыл бұрын
Superb cool telescope 🔭❤️ dear, thank you for informational video... Fully enjoyed 😀💖🎁🎁🎁🎉🎉🎉🎉🎉
@keremtopal18243 жыл бұрын
How can I get this sketch?
@Starfox-zg4tk4 жыл бұрын
How much. I need a base
@alexandreevangelistadasilv79893 ай бұрын
Wow!😅
@nataturoiii52312 жыл бұрын
good job
@eduardovasquez67394 жыл бұрын
Podría compartir los moldes??
@petelaci5 жыл бұрын
Szép! Mivel telítetted a rétegelt lemezt? Vízállóságra gondolok.
@horvathtamas34765 жыл бұрын
Csónaklakkal.
@PuddintameXYZ3 жыл бұрын
I am here to add to the voices of the comment section in asking if you have any plans you might share for this.
@horvathtamas34763 жыл бұрын
Hello! It's an old design, the plans no more available.
@PuddintameXYZ3 жыл бұрын
@@horvathtamas3476 Aw, too bad. Thanks anyway!
@drewcarruthers7113 жыл бұрын
@@horvathtamas3476 please please please find the plans! who know you might be able to make a few $$
@szaki5 жыл бұрын
Nem mindenkinek van CNC gepe otthon!
@horvathtamas34765 жыл бұрын
Nekem sem volt, amíg nem terveztem és építettem. Nem csak cnc-géppel lehet zsámolyt készíteni!
@ronjones40694 жыл бұрын
There was no information at all, only a few minutes of watching power tools. Nothing about why you did this, to cautions about what to look out for, no suggestions of other methods, nothing worthwhile. Too bad, because you went to a lot of trouble to make the video and the mount. Thanks anyhow.
@insaneinthemembrane383 Жыл бұрын
its not a tutorial
@pdu9994 жыл бұрын
Terrible angry music really detracts from what you are trying to convey. Can't watch this ...
@RCzan134 жыл бұрын
I liked the music.
@Handles-R-Lame4 жыл бұрын
Me too, work calls for work music. Star gazing calls for ambience. Man at work.
@Handles-R-Lame4 жыл бұрын
Also very assuming of you to call it "angry" it may be peaceful to some.
@epic_playz42833 жыл бұрын
I hate rock.
@szaki3 жыл бұрын
Skip the crap music!
@horvathtamas34763 жыл бұрын
If it’s not your style, not my fault. You can switch off you speaker, while you watch the video.
@szaki3 жыл бұрын
@@horvathtamas3476 When you go to a star party observing , you blast place with hard rock or techno music? Poor soul!
@horvathtamas34763 жыл бұрын
Dear szaki. This is not relevant. I obseving without any music or noise. This is two different thing, don’t mix them.