In this video I make a popper lure specifically for fishing the Florida flats and I add a little something extra to call the fish. www.amazon.com... / engineeredangler www.instagram....
Пікірлер: 70
@tedmemo96253 ай бұрын
Another great build Franko. Thank you for sharing your recipe for the Polyacrylic mid coat. It is more than greatly appreciated.
@EngineeredAngler3 ай бұрын
My pleasure!
@pieter-matthijsbolt63753 ай бұрын
Same here. I get all the steps right and then the final clear is buggin me. I'm goin to try a mid coat this weekend! Thanks alot!
@paulbowkunowicz69603 ай бұрын
Thanks for explaining the Polycrylic...on how you prep it
@EngineeredAngler3 ай бұрын
You bet
@saltygenes3 ай бұрын
That guy holding the underwater camera must be out of air by now 😂
@itllkeal3 ай бұрын
😅
@itllkeal3 ай бұрын
I do the opposite after watching Matt Stephen talk about his poppers so I have been weighting the tails and tying hair on the back hook so it sits more vertically and it amazes me that sometimes the fish will come up and grab the tail hook and pull it under like a bobber. I can fish about 10 minutes per cast now without all the long pauses. It'll pop and move about 3 to 6 inches if you want to fish slow
@davidbailey95873 ай бұрын
Hey, remember those old sticker dart guns? The were a spring, a catch and a plunger-shaped "dart" with a shaft and suction cup. So what if you had a spring-loaded popper face? When you popped it the front cup would compress the spring. Then the cup would spring back and kind of double-pop the lure.
@mike12613 ай бұрын
So true about cedar. I am working on ten 2-piece swimbaits and have had chip-outs several times. Man, I'll bet that popper shows up on your local doppler!
@lannabulls3 ай бұрын
Thanks Franco, The idea of a simple rattler made by a straw is excellent, I learned it thanks to you. It fails sometime in a resin casted lure, it happens often, at list to me, that it doesn't work, the sphere, probabbly cause the straw soft plastic, it doesn't move. Only in cast resin lures I use a rigid straw made in brass. Thanks 🙏 so much for your excellent job, you nail it again!
@EngineeredAngler3 ай бұрын
I haven't that issue with the plastic straws I use.
@lannabulls3 ай бұрын
I anderstood why, sometime, the straw it doesn't work, once resin is casted, I use to put my mold inside a pressure pot. I suspect that, cause the pressure, air pump in, the straw that is not completely rigid sometime is "crashed", steel balls are not allowed to move. When I don't use the pressure pot straw is working always fine
@swiftbleach173 ай бұрын
At the 3 mins mark i already know this is gonna be a great build
@EngineeredAngler3 ай бұрын
Thank you.
@user-ou1mz5ob4c3 ай бұрын
...and again caught some new ideas which I will test as soon as possible in my workshop. Thank you !
@maniachill30693 ай бұрын
Hey Franco, great video once again. Hello from Maine, Kevin
@EngineeredAngler3 ай бұрын
Hey, thanks!
@codykaufman58553 ай бұрын
I like to use a appropriate size glass bead in place of the nail head. Another great video. I really appreciate your content.
@EngineeredAngler3 ай бұрын
Awesome! Thank you!
@nickcallegari2 ай бұрын
I’d love to see a video on making a sinking stick bait for saltwater!! for the type of fishing i do in Sydney Australia I would really like to make one I just don’t know what to use to make it sink! Love the video!!!
@EngineeredAngler2 ай бұрын
Great suggestion!
@HHH-nv9xb3 ай бұрын
i tried brushing on Polycrylic on top of airbrush paint. You will need to make sure the paint is thoroughly dry and use a soft brush. A stiff brush could rub the paint on. It seems spraying on would be better. I need to try it.
@xnorcal831x3 ай бұрын
Thought of a video that others might like.How deep should a wire harness be inside a bait before its rips out? Have a couple baits with harnesses at diffrent depths. Have a force gauge tied to a hook hanger and rip them out.
@johnharder5618Ай бұрын
Love the video I just got back from bass fishing 10 PM-4 AM I like your design for a popper But at night I use a plain Black popper But I think a Bullfrog paint would work well during the day
@Bobo_733 ай бұрын
Awesome lure! Keep up the great work!
@EngineeredAngler3 ай бұрын
Thanks! Will do!
@midatlanticangler7473 ай бұрын
this is awesome man! just found your channel and im graduating with a degree im ocean engineering this year. im a big fisherman and also started making lures over the past year! About to take my FE exam!
@EngineeredAngler3 ай бұрын
Good luck....FE material isn't too bad but the fatigue factor with such a long test can get you.
@wesneal79133 ай бұрын
Love the paint job you gave that. Great looking lure
@EngineeredAngler3 ай бұрын
Thanks 👍
@dean34713 ай бұрын
WOW!!! You really are a very talented man.
@EngineeredAngler3 ай бұрын
Thank you very much!
@stripermanly3 ай бұрын
Good job Franco
@comfortablynumb93423 ай бұрын
Why not use a metal tube for the rattle chamber? It might be cool to put an empty shell case from a rifle in there for the chamber, and you'd only need to close one end.
@raygissendanner14763 ай бұрын
Great video and great looking lure
@EngineeredAngler3 ай бұрын
Thanks 👍
@TheCopperVillageAngler3 ай бұрын
Nice colors!
@EngineeredAngler3 ай бұрын
Thank you! Cheers!
@jvjoe43763 ай бұрын
Great channel...!! Question, have you ever thought of replacing the treble hooks with inline hooks? Thanks for posting.
@EngineeredAngler3 ай бұрын
Yes I have but when I have the hook up rate goes down.
@alexandreespindulaferreira32983 ай бұрын
Splash 👏🏻👏🏻👏🏻👏🏻
@jamesstewart53713 ай бұрын
A while back you made a J plug but an issue with your boat prevented a video of the lure in action did you ever post a video?
@EngineeredAngler3 ай бұрын
Not yet but I did get some footage. Keep an eye out for a short.
@juderyan1284Ай бұрын
Somehow missed this one. Really nice lure you turned out on this one. Just a question, is the cup really necessary, as in could you cut out say a wave or C type shape (for want of a better way to describe it) on the bandsaw and still get the same effect? Only that I don't have a ball bit or any way to scoop it out (well i do have a spoon gouge but that would be tricky)
@EngineeredAngler29 күн бұрын
Sure, you can cut a concave front and it will work ok, just need to angle it down so it won't pull the lure under.
@juderyan128429 күн бұрын
@EngineeredAngler thanks for the response, will give it a go. Just need to work out the straw part now, can no longer get straws in Australia. Thanks again 😀
@ukirbayeman76443 ай бұрын
Can i request dive popper please, franco version is the best absolutly 😊
@pmpkmc3 ай бұрын
Hi Franco, another sweet build! I have a question for you, i was making a new mold the other day and i forgot to divot the clay so i did not have a key to align the 2 halves. Of course i figured this other when preparing for the 2nd half. How would you address that situation? What i did in the end was only vaseline 1/2 the mold, but I'm not sure i'm happy with it as its difficult to get the internals properly positioned. But i just made a handful of harnesses so we'll see if i can learn to live with it.
@EngineeredAngler3 ай бұрын
I had included this in a video a while back...I created divots using a thin tube with the edge sharpened by digging out little cylinders in the face of the first half of the mold. You can use the eraser end of a pencil by taking out the eraser. Good question. Thank you.
@pmpkmc3 ай бұрын
@@EngineeredAngler Cool, i appropriate it.
@vladkh10683 ай бұрын
I bought silicon lure. Has a very strong "chemical odor". How to get rid of it? I really like watching your channel. Thank you.
@EngineeredAngler3 ай бұрын
Sorry I don't know.
@magcolor3 ай бұрын
👍👍👍👍👍
@saltygenes3 ай бұрын
Where do you get your polycrylic for $11? Everywhere I look it's $26. I got mine for $26. Very cool lures brotha 👍. I just started airbrushing my own lures 3 weeks ago and I'm having so much fun. Thanks for the vid 👍
@Fish-Erman3 ай бұрын
It probably was $11 when he bought it 3 years ago. Thanks bidenomics!
@EngineeredAngler3 ай бұрын
Damn...its been awhile since I bought any...the price has doubled.
@Straight0uttaCrofton3 ай бұрын
toothy predators beware
@johnwilcox82143 ай бұрын
Great job, have you ever made a lure out of pvc board
@EngineeredAngler3 ай бұрын
Yes I have
@johnwilcox82143 ай бұрын
@@EngineeredAngler I just watched 2 of your videos using pvc board right after I asked. You do a great job
@user-tl1bk1ok3c3 ай бұрын
I have a question about a crankbait sorry but what would cause the bait to roll when you burn it Thanks and I enjoy your videos they made me want to try to build my own
@EngineeredAngler3 ай бұрын
Misaligned bib is the most likely answer.
@user-tl1bk1ok3c3 ай бұрын
@@EngineeredAngler I’m sorry but I’m new to this what is a bib
@goran79kt3 ай бұрын
@@user-tl1bk1ok3c bib refers to a lip which gives an action of a lure. Unless you made lipless crankbait 😀Then you again need #EngineeredAngler to answer it to you.
@user-tl1bk1ok3c3 ай бұрын
@@goran79kt would that not be called a bill
@mahmoudaghaei69263 ай бұрын
Do you not add weight for CG?
@EngineeredAngler3 ай бұрын
No need on this one...
@anon589733 ай бұрын
Very cool. What about adding a feathered treble to the back?
@EngineeredAngler3 ай бұрын
I like that idea....might do it for the saltwater trip