Making BLDC Motor || Brushless DC Motor

[@bilalkurt5301]

It was a really nice and productive video, thank you.

[@thelankanatriz]

Please show us rotation speed with same voltage in different motors.

[@noutram1000]

I would be interested in relative max. output power of the 3 types or any other data that differentiates them in order to answer the question: why bother with more stators/winding/complexity?

[@Suzuki_Hiakura]

The relative max output power would always be limited, most definitely by the magnets. They will only attract up to a certain point; the magnets are pulled by the electromagnetic properties of the coils, but while electromagnets can be given more power, regular magnets will have a finite limit on power. The stator is the entire part of the motor that has the coil windings, so I assume you were referring to the coil windings in your question. More coils will essentially increase the amount of magnets that can pull the permanent (neodymium) magnets. More windings will increase the voltage that can go through it, which would increase the rpm of it. A thicker cable would increase the maximum amperage and overall torque of the motor. Unsure what you meant about complexity though. Did you mean why multiple coils are continued across the stator? Knowing the gauge of the wire, the number of turns, the number of coils, and the control board's output should be able to give an approximate relative max output power of the three types of motors, but that’s about it.

[@manman-sg1zt]

NIcely done I would say, really nice.

[@Cjudd001]

Why not use iron steel spacers to amplify your windings.. Of course silicon steel is better or ferrite for the HF

[@satyakiduttaroy7081]

Guess optimum balance for motor weight and thrust ratio

[@nguyenhop]

Rất tuyệt vời, cảm ơn bạn

[@hernandezmedelaxelisai5341]

Excuse me, can you use the XR-105 controller?

[@MOAllDa]

Pretty cool ❤

[@unglaubichuberlieber8048]

greetings !!! BRAVO!!! BRAVO!!! BRAVO !!! MANY MANY THANKS FOR YOUR DETAILED ILLUSTRATION especially the # of turns ... hahaha will you share the info/3d prints on the poles ???

[@austinbambooinc2507]

Hm, he's using three wires for three phases but, if it's DC it needs to be six wires to change the polarity in the coil. If it's AC, or even if you rely on the field collapse to act as the reversed polarity, there needs to be a return/ground wire.

[@dhaneshsinroja9083]

👌👌👌👌bahot khub

[@Alihassan78910]

Input volt ??? And rpm ? 😊 thanks bro😊❤

[@SaravanaKumarJANU]

Hi, Will this motor work with 20A ESC and a servo controller? I replicated this motor with six pole BLDC but is not working with this ESC or should I use only 12V - 36V same controller that you are using? Can you guide me on this please.

[@reallifework1375]

did you buy the coil from the description he gave he is a liar we need to use enamelled insulation copper coil but he gave without insulation in the description

[@indeterminatedude7334]

What kind of rpm are you getting on this thing

[@MukeshSharma-ku2up]

Did you check the rpm and thrust of it? If possible check and revert back

[@cesarrodriguez-tw9bp]

Very impressive ... subscribed!

[@vitthalnikam4917]

Very nice video.

[@mrstanlez]

6 coils and 4 magnets only ? 9 coils and 6 magnets only ? Why are these magnet not polarizes towards coils ?

[@yahirvillalba3784]

This motor can work as a power generator at the same time or another type of winding is needed

[@mohamedsamy1431]

This motor converts electrical energy to mechanical energy. To generate energy, you need another source of energy. Don't forget about the law of conservation of energy.

[@robinhooper7702]

Yes you can

[@huggins2012]

Tesla stated that the numbers 3 6 9 are the keys to the universe

[@potat0441]

Damn she fine

[@pakeezafraz3487]

Amazing 😮

[@jasonredus6127]

Which one is more for power than speed

[@austenelectricalsolutions3492]

Awesome project! Thank you for your inspiration! Is there a difference in power, rpm, performance between the 3 pole vs 9? Thank-you again and keep them coming!

[@mohammedk5573]

absolutely but the wire turns got a different as well

[@bongobarta1908]

@@mohammedk5573 wht will be the ratio of number of pole and number of coil turn?

[@alessandromanente2809]

Is it important the width of the wire? Because I followed all the steps using a 0.5mm one but it doesn't work and I don't know if it depends on which wire you use

[@LincolnRattes]

How can I buy this? Do you have to sell?

[@swedishpsychopath8795]

In the description: The link to the bldc controller isn't working. Could you fix the link?

[@TerryBecker-bw1vx]

So I this case Teslas 3 6 9 applies to motor scaling the number of coils.

[@NormanWray-hi8cu]

Hello dear yes sir that's great I rate you and you is great thank 😊😅

[@prerupa]

the rotation of the field with the 9 pole motor is the slowest with high torque, the six is in the middle and the 3 is the fastest with low torque.

[@MrStrocko]

Истину глаголишь , сын мой ! (с) А ещё у резистора два конца , а у потенциометра три , во как !

[@techsecret6474]

Is it 12 volt or 24 volt, if I make a round of 60 turns not 40 , what happen then how much battery volt I need to run this.

[@Zaqkashimoto]

How would one reduce the noise? Though nice Job.

[@ganeshharisankar.rd173]

Excellent 🌹🌹🌹🌹🌹👍👍👍👍👍🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏

[@noname710]

100 % people watch but 2% people's try to make 😂😂😂😂❤️❤️❤️

[@yigittimurarpack9949]

Hello great job. I have a question: did you use the same magnets for each 3 motors? And the magnet link is missing,can you give the dimensions of magnets for each motor? Thank you.

[@mahimaswetha]

What is the plastic like material used here to wind the copper wire?

[@HarianOtomotif]

Its pvc

[@SaravanaKumarJANU]

It is PLA

[@ryanmckenna2047]

@@HarianOtomotifI thought you had to use a conductive material, like laminated electrical steel or smc, wouldn't plastic just overheat and melt?

[@ryanmckenna2047]

@@SaravanaKumarJANU @hahahaha.......9216 I thought you had to use a conductive material, like laminated electrical steel or smc, wouldn't plastic just overheat and melt?

[@sunilalexandercampianregis8874]

Very nice video, but can you show how to build DIY motor controller for these motors

[@elektrikselboyut3604]

How did you find the number of windings?

[@somerandomguy7895]

I have no idea

[@horrorsilentpicture456]

Which one is Higher RPM.

[@thomascameron683]

BLDC motors use much less copper. Therefore it should be less costly. Why its market price is more?

[@zbhatti4u]

Nice video But plz add diagram of coils connections

[@paulwright5440]

What's the point of carving out a disc shape for the outside of the motor when the magnets are in the middle 🤔 surely it would be easier for winding the coils if those bit of plastic weren't in the way

[@techsecret6474]

Is that can be used on cycle, How should i find 12 or 24 volt motor

[@sahinkatecnologyinvention4986]

Good perfect successful project

[@techsecret6474]

Number 3 can be used on Cycle Motor? Can you make a vedio With a Running cycle?

[@Naoricarew]

Can i sell?

[@makeyourowntechnology9288]

Wow amazing video bro👍👍💖

[@L-Dog-G]

Epic video, very nice design and process, i will be using this to make one

[@awaitingthetrumpetcall4529]

I agree. Since I don't have a CNC I'll have to use a compass, right angle square and a dremel tool to make the stator.

[@L-Dog-G]

@@awaitingthetrumpetcall4529 Accuracy is key... To make a functional motor is a useful skill.

[@awaitingthetrumpetcall4529]

@@L-Dog-G Quote: _"To make a functional motor is a useful skill."_ If you only knew! One of my hobbies is programming micro controllers. When I discovered that I could change the behavior of a motor by writing instructions I knew I had wasted my college career! I learned to control steppers, brushed DC's and servos but I never mastered sensorless BLDC's. I only have a dual trace oscilloscope and the BLDC is a three phase motor. I want to build a triple half H-bridge to drive a sensorless BLDC motor. Building a 3 stator-coil sensorless brushless motor ...and... a driver circuit would be ideal.

[@L-Dog-G]

@@awaitingthetrumpetcall4529 that sounds amazing bro. By sensorless you mean Hall sensor? ... You can run Brushless without hall sensors but this is crude

[@awaitingthetrumpetcall4529]

@@L-Dog-G I don't want to use Hal sensors. My focus is on high speed brushless motors. I experimented with comparing three op amps to the neutral point in an attempt to detect each point in a six step commutation sequence but I failed in every case. I really like this stuff. I'm not gonna give up. EDIT: I used transistors in my experiments. I want to build a circuit using N channel mosfets in a bootstrap circuit.

[@CircuitNotion]

How many turns have you used

[@Sandip_patel1309]

I have doubt about motor stator how can it works without any metal. you can't use any metal in stator and its work how? Motor can't work in plastic stator

[@santri_elit]

Thanks your video👍

[@MrStrocko]

Почему нас учили что статор мотается только на железе Э305 , а тут голимый пластик и работает , конечно хар-ки будут другие , но это и на порядок дешевле чем из железа

[@ryanmckenna2047]

what is the structure made of?

[@busandbuschannel]

Tolong jelaskan bagaimana caranya lebih detail penyambungan kawat tembaga dari A B C dan seterusnya hingga hidup

[@twingoldman3751]

Hi thats cool

[@ernieschatz3783]

It's not a DC motor. What comes out of the ESC to drive it?

[@tiger_boi826]

Its actually pulsating DC

[@mukundanpp7018]

Moving part is magnet. So no need brushes. The current from the board is pulsating dc.

[@karitatoom]

wow emezing

[@bitsurfer0101]

Why do you only have 6 magnets on a 9 pole motor?

[@danieldias3838]

Quantos Volts é aplicado sobre o motor amigo? para fazer esses testes? Desde já lhe agradeço muito e meus parabéns pela sua inteligência 👏👏👏👏👏👏❤️

[@somerandomguy7895]

25 volts

[@jasonmorgan661]

This better show everthing including where the hall efect sensor goes. Every wind your own motor video seems to leave something out.😕

[@akashdeeplakra3583]

He uses electronic speed controller ESC no need for Hall sensor 🙏

[@abhijeetkedar1551]

@@akashdeeplakra3583 even if you are using electronic speed controller.... Hall effect sensor is required to locate accurate position of rotor.. 🙏

[@darenpearce7773]

No hall needed it's a puls signal / mosfets controller Think of it as A big rc 3 phase bldc motor.

​@@abhijeetkedar1551in the e bike, i removed the sensor cables but it's works very well Elhamdülillah.

[@djksfhakhaks]

​@@abhijeetkedar1551I've never seen a hobby brushless ESC that even has pins for a hall effect sensor.

[@carlindrawing8610]

da para fazer aeromodelo com esses motores?

[@moemn_sabah9252]

What is the name of the device that connects the electricity of the electric motor?

[@HiRideEV]

a bldc controller

[@rihemtaibi1933]

How do you determin the dimensions of all the parts?

[@marcovalentinoalvarado3290]

Takes a lot of maths, Integrals and Inductivity calculus!

[@rihemtaibi1933]

Which sizing method do you recommend? since I'm studying aeronautical engineering and my team is assigned to make BLDC

[@techsecret6474]

Is it used to be a cycle motor...

[@wycliffochola]

Kindly show circuit diagram

[@Samuele_Giuliano]

how is wired the coil?

[@hajurivijaydip3571]

Bro how you use odd number of pole????

[@MukeshKumar-jw6ji]

Wiring connection kayse kiye ho bro 1, 2 , 3 , no ke hisaab se ? Startin aur ending wire ka kayse connection bro ? Video mein thheek se pata nahin chal paya.

[@CasamTheAnimator]

1 - single 2 - double 3 - triple

[@viscourtroy]

Oh the wire has the isolation coating. The end of the wire strip off the coating and tight with the standard knot. I cannot understand the sequence and which side of the end tighten with the other one... I am stupid and lack of observation ability... and the patient!😅😅😑😑

[@rocioguevaraobando9075]

Maravilloso! Gracias. Thanks. Merci. 🙂🙏🏻💚

[@srinivasreddy-zy2ru]

Can u tell the dimensions of parts used in making stator ?

[@shyambabuthakur7730]

Bad motor ka reguletor kit kase milega

[@omerfarukseckin]

what is thr formule of turns why 100 ı want to learn?

[@zzenithgamer4302]

Max rpm?

[@mingosutu]

This is showing off. I thought it was a tutorial

[@TechnicalSupportTech-gb6sl]

Sir how you calculate number of Turns and number of Gauge please 🥺 guide me, I'm ready for the pay for this information

[@mighty2631]

Hi. Would appreciate verbal instructions also Thanks

[@SergeySamodelkin782]

👍👋

[@Larry76775]

Do you have the links to the models to cnc machine? Thank you in advance.

[@somerandomguy7895]

He probably does not xd

[@almahdidaudzuhdi1152]

What conclusion, RPM, Torsi..??🤔

[@sarveshchauhan855]

Mujhe bhi bana na hai bhai saman kaha milega batao Bhai

[@anamulhasan8039]

sir I wanted to make a e bike. please make a habby motor that can run e bike

[@bang-ga]

I think You are confusing the use of the terms pole and slot.

[@AbyssalBob]

What do you mean by this

[@jamallaidley4718]

Cool 😎

[@ИгорьЛюбарский-ж2ь]

надо было для чистоты эксперимента ток потребления показать

[@aleks-mar]

Дело даже не в токе потребления а в крутящем моменте. Он около нулевой. Магнитопровода нет вообще....

[@MrStrocko]

@@aleks-marно пропеллер то свистит

[@aleks-mar]

@@MrStrocko а кто сказал, что свист от этого пропеллера, там рядом настоящий мотор свистел, а в кадре было это недоразумение. Хватит быть такими наивными. Если бы так можно было бы, то так и делали бы все заводы. Изучайте физику, чтоб не вестись на подобную лапшу.

[@MrStrocko]

@@aleks-mar Что это вы так возбудились , а ТОЭ и Эл.Машины я изучал тогда когда ваш папа гадил малышом дальше чем видел !

[@aleks-mar]

@@MrStrocko я рад за Вас! Изучали, да видать так и не изучили толком ничего, если в такие ролики верите.

[@UsingUsing01]

Is this power to fly

[@updater__x3969]

PLEASE REPLY my doubt : if we rotate the shaft of this project by connecting it to a other motor , will voltage is induced in the stator winding .

[@robinhooper7702]

Yes, but use a stream or a wind propeller for your input power.

[@dawni2172]

why you never show the power supply. ?

[@ashwinikshirsagar7734]

What is speed of 9

[@k192447]

muito bommmmmmmmmmmmmmmmmmm.

[@Nothing_us777]

Where I could But to make Bldc motor making pls tell.

[@alexandres8846]

more poles = low speed but increase torque.

[@Cjudd001]

And you could add a outer cage for an out-runner in runner configuration to increase the magnetic field and play with the number of turns for rpm

[@newtonbaba2974]

Wire Connection bhi explain kiya karo bhaai hamare liye to useless hai ye video hame connection ka Hi nahi pata aur na hi tumane bataya

[@taoyan-se7sz]

Hi everyone, I want to know why 3 pole refers to 2 neodymium magnet，6 pole refers to 4 neodymium magnet，and 9 pole refers to 6 neodymium magnet ?

[@gassanjad3955]

كل شكر واحترام

[@electronicswork7746]

Over heat and melt pvc

[@sangarp2001]

where did you buy that speed controller?

[@zebra-_-290]

Your welcome

[@nogardd]

NASA is gonna use it to go to Mars

[@meertughral7371]

On How much voltage you operating this motor

[@somerandomguy7895]

25 volts