Part 3 where I make the plate and Ring Roller of my Ultimate Bending Machine
Пікірлер: 47
@joell4396 жыл бұрын
First rate workmanship. Thanks so much for sharing. This has been a great series to watch. Joel....
@bartharkemametalworks22996 жыл бұрын
Thank you Joel!
@The52brandon5 жыл бұрын
You can use the flap disc longer mostly due to using all of the contact surface. When handheld, no matter how hard you might try, you'll favor one edge of the disc (for me that's the outside edge)
@barretharms69483 жыл бұрын
Probly would have gone with sicker wall tubing because it limits the sheet that you can bend to less than the wall of the tube, Although obviously easy sickness of the shaft would make a bit of a difference as well you can't have the shaft weaker then the tubing.
@adriancoetzee656 жыл бұрын
You are a truly skilled craftsman Bart. I aspire to that level of work.
@bartharkemametalworks22996 жыл бұрын
Thanks!
@drewt32104 жыл бұрын
great build & thank you for sharing! Might be possible to connect both side adjustment screws of the roller with chain driven gears. Just a thought.
@BleuCollarFndryMTL Жыл бұрын
Your tig welding looks beautiful. I wish I knew how to make the acme threads.
@bartharkemametalworks2299 Жыл бұрын
Thanks. And about the Acme. I just bought them and there relatively cheap.
@gordtemple7645 жыл бұрын
Excellent workmanship. Bart, try a swivel head torch. You can easier maintain a comfortable hand position. Again nice work. ABC's of welding Always be comfortable.
@bartharkemametalworks22995 жыл бұрын
Thank you. And a few month ago I bought a Lincoln Invertec (V200-t) with a flex head. I Like it a lot and agree that its a lot easier to keep a comfortable hand position.
@daviddaddy6 жыл бұрын
Hi Bart, man what a Nice Machine you're Fabricating! You're A very good Fabricator, Machinist and Welder! Very Nice Work Bro, Thank you very much for sharing, Im looking Forward to the next Video. Have a Very Blessed and Good Day Bart.
@bartharkemametalworks22996 жыл бұрын
Thank you!
@bharatdodia86884 жыл бұрын
Hi sir iam bharat tacnicis very good
@bartharkemametalworks22994 жыл бұрын
Thank you Bharat
@Guds7774 жыл бұрын
And if you build the frame higher and stronger then you can add a shop press in to the mix, even put a plate bender and a shear to, i love combo tools with a small footprint...
@bartharkemametalworks22994 жыл бұрын
Yes, you could make even more combinations. But I already have a shear and will build a heavy duty forge press in the near future.
@dawdawsd13 жыл бұрын
Hi Bart, I think you could have built your ring roller just as a set of another attachment to the top plate, which would allow you also make smaller diameter rings
@bartharkemametalworks22993 жыл бұрын
Yes good idea. That would make a nice addition 👍
@428Mario4 жыл бұрын
Like your work, nice integrated design. But always a but. Lol In a Lot of places you use heavycwall stock and heavy flat bar then barely weld it, no weld prep for penetration, just on the surface. Then in many places you grind the welds. Not much holding it. The rect tube with flat bar at each end near the start is an example. Just wondering
@bartharkemametalworks22994 жыл бұрын
Yes, you are right about the welding. On some parts it could use some more beveling and I need to take some more time for that. But for the forces that it needs to hold it's more than enough.
@jimburns3484 жыл бұрын
Excellent work! How did you manage keeping the materials from starting to rust?? Workshop must really be low humidity.
@bartharkemametalworks22994 жыл бұрын
Well I did have some rust problems but most of the build was during summer time and then it's fine for a few weeks. And I did a good cleaning before paint. In the winter it's really terrible with humidity in my workshop but I am moving in about a week.
@chrisnixon21793 жыл бұрын
You need to build a 2x72 belt sander/grinder
@bartharkemametalworks22993 жыл бұрын
I did two already. See my video's
@halyenwe6 жыл бұрын
Love these videos Bart. Thanks for posting. Awesome work.
@bartharkemametalworks22996 жыл бұрын
Thank you Bret
@barretharms69483 жыл бұрын
Yeah I'd have gone for the key ways key ways don't wobble
@jeffanderson16534 жыл бұрын
You should teach tig welding. You are an artist sir.
@bartharkemametalworks22994 жыл бұрын
Thank you Jeff. Sometimes I do teach Tig welding at home but not on KZbin. Maybe I could try that sometime. But there are already a lot of good video's about that.
@henrikhv50846 жыл бұрын
great video :-) i really liked the part were you build ind some support for the pipes :-) that was a great idea, thank you
@bartharkemametalworks22996 жыл бұрын
Thank you Hendrik
@michaeltheMACHINIST4 жыл бұрын
Great job my friend i do the same job but a bigger one but motorized
@bartharkemametalworks22994 жыл бұрын
Nice!
@nigelcharkoo45595 жыл бұрын
best i have seen great job
@bartharkemametalworks22995 жыл бұрын
Thank you
@bentumbentum6 жыл бұрын
Perfect work...congratulation
@bartharkemametalworks22996 жыл бұрын
Thank you
@jakegingrich72145 жыл бұрын
What brand is step drill bit do you use
@bartharkemametalworks22995 жыл бұрын
Phantom 6-25mm HSS. Used (and sometimes misused) it for around 5 years and it's still in good condition.
@aliafreet4 жыл бұрын
👍👍👍😊🌹
@robbysamosir61132 жыл бұрын
its too hard for traditional warehouse 🙏
@ammarouachen48505 жыл бұрын
Where are from my brather ?
@8477willy5 жыл бұрын
leuke video
@bartharkemametalworks22995 жыл бұрын
Dank je
@saberabdelhadi56374 жыл бұрын
👍👏
@J1I9M7M4Y4 жыл бұрын
So... You used the machine you are building, to build the machine you are building.. 🤔😮🙃