Marlin Firmware Builder

Recently I have had a lot of people reaching out with issues related to building their own custom Marlin firmware due to various reasons. For that reason, I created this video showing you how to use a online firmware builder. It does require a small donation to use but may save you a lot of time/headaches.
If you have any questions on the content covered in this video, feel free to leave a comment below with them. I try to reply to all commented within 48 hours.
Resources
Our Site: 3dprintscape.com
Firmware Builder: marlin.crc.id.au/
3D Printscape Firmware: 3dprintscape.c...
Recommended Hardware
Ender 3 Pro on Amazon: geni.us/vIAIx
Ender 3 V2 on Amazon: geni.us/ur8YHM
HATCHBOX Filament on Amazon: geni.us/BJx0Gdj
Need Assistance?
Join us on Discord: / discord
Please consider helping support the channel through Patreon so we can continue to develop new content. / 3dprintscape
*This channel is owned and operated by 3D Printscape. 3D Printscape is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.

[@GrandTheftHollow]

definitely a great next step for beginners in the 3d printing space, needed this last week but I ended up just learning VScode and compiled successfully thanks to your older videos!

[@3DPrintscape]

Hi. I’m glad you were able to get vs code working. Being able to build it yourself is a good skill to have.

[@Vicorcivius]

you have to "Donate" to use a service. That is not what a donation is. That is paying for a service.

[@3DPrintscape]

Hi. I understand what you’re saying, it’s basically a yearly subscription fee.

[@raymondcowey1041]

@@3DPrintscape Semantics

[@3DPrintscape]

@@raymondcowey1041 ya basically

[@larkinduval1882]

Thank you for the info on the marlin firmware update website!

[@3DPrintscape]

You bet!

[@Nojokebeatz]

Thanks for the video. The steps were straightforward to follow. So, I used 8 of 10 of my downloads trying to get Marlin to work with Ender 3, Cr-Touch, Sprite Extruder, and a run-out sensor. My Creality touch screen never loads, the boot-up screen never works, and the new software has never been installed.

[@3DPrintscape]

Hi. I was never able to get the creality touch screen to work with marlin. Not sure if you had it working prior to doing this upgrade or not but it may just not work.

[@Nojokebeatz]

@@3DPrintscape Are there any alternatives to using marlin? I was running Creality OS before my failed attempt.

[@3DPrintscape]

@@Nojokebeatz Not with that screen that i know of. If you use klipper the screen would just be off.

[@TheMeq]

Hi, I have the Ender 3 Pro with the SKR Mini E3 V3.0, TFT35 E3 V3.0.1 and a BL Touch. I am using the firmware from your website, and tried to follow one of your other tutorials, but my ABL menu isn't in the same place yours is in, and I don't have the Z Probe Offset Wizard. I have a P Probe Offset Wizard which looks similar to the Z Probe Offset Wizard, but when I press the button labelled "OFF" to switch it On, the printer moves the nozzle around a bit and then the screen locks up. I can't figure out how to get this to work, any idea's on what I'm missing?

[@3DPrintscape]

Hi. The firmware on my site should work fine in this case but setting the z offset will be different with the tft35. I think they did end up calling it p offset but i would need to update my tft to see exactly what they changed. Maybe someone here or on discord can help fill in the gaps.

[@Irek_Poland]

SUPER!! THX Bro!

[@3DPrintscape]

You're welcome!

[@tomstephens326]

Thank you all the great video's, I have a question I updated my board to a Bigtreetech SKR mini v.3 running Marlin.I have a Spider hotend. when I started testing it the temp would go up to 260 even though I sent it for 215. It will slowly drop and fluctuate from 213 to 220,and never hold temp. Have you hear of this before?

[@3DPrintscape]

Hi. I have not seen this before, there could be something up with your hot end thermistor.

[@tomstephens326]

@@3DPrintscape Thank you very much for the reply I will get another one and see if it helps.

[@tomstephens326]

@@3DPrintscape I was able to work it out it was the heating element, the spider I got did not come with the wiring harness. So I got one from Amazon but I got the 12V not the 24V once I replaced that it works perfect. Thanks for the help.

[@gruffmonster3232]

could you add a high temp (300c) skr e3 mini v3 with dual z axis

[@3DPrintscape]

Hi. Can you reach out to me via email ([e-mail]) or on discord.

[@polyalex_]

4.2.2, i have updated thru creality.(Ender-3 ProMarlin2.0.6HW4.2.2EuropeMultiLanguage 29 Nov. 2022.) your videos said you like to stay away from stock creality firmware. so my question now is how do i pick between 512 or 256?

[@polyalex_]

i found my cpu its RTE6 so i think the 512 yes?

[@3DPrintscape]

Hi. Yes if you have the RET6 cpu its 512k.

[@polyalex_]

@@3DPrintscape seems to be working great! thanks!

[@SimonsSolarShed]

Hi inwas wondering if you could help build my btt skr mini v2 firmware? I have an ender 3 with stock lcd with rotary encoder, dual z axis,sprite pro,crtouch the crtouch is mounted front left of nozzle still have the end stop micro switch build plate 230×230. Love your videos I'm now subscribed. Regards Simon.

[@3DPrintscape]

Hi. Can you reach out to me via email ([e-mail]) or on discord.

[@SimonsSolarShed]

@3DPrintscape hi yes I will do that. Thank you for replying.

[@gruffmonster3232]

first. i know its overdone

[@3DPrintscape]

Hi. What is overdone?

[@gruffmonster3232]

@@3DPrintscape the comment of first

[@GreyGhost-r4z]

WHY am I getting errors ? I don't understand. Build Reference: e0e7bc56 Submit time: 2024-09-09 01:07:26 UTC Last Change: 2024-09-09 01:07:30 UTC Current Status: Build Failed! Builder Allocated: syd-builder.crc.id.au Errors: buildroot/share/PlatformIO/scripts/../../../../Marlin/src/inc/../../Configuration.h:23:2: error: "Don't build with import-2.1.x configurations!" buildroot/share/PlatformIO/scripts/../../../../Marlin/src/inc/../../Configuration.h:24:2: error: "Use the 'bugfix...' or 'release...' configurations matching your Marlin version."

[@3DPrintscape]

Hi. It looks like your config file isnt from the same version as the source. Dont use an old config, make the changed in the new one.

[@GreyGhost-r4z]

@@3DPrintscape Thanks for the help. I figured the main file was just the 2.1.2.4 bug fix version then selected for the individual needs from The selection. Is there a way to understand the Classic Jerk settings vs the new settings. I’m on the 4.2.7 board. I have an Ender3 Pro. Manual bed leveling but I do like that I may be able to add a probe. Just not sure which one. BL , CR or the other offerings. I print occasionally. Have a Metal bed. I’m just trying to get it going like it was. Loving your videos.

[@3DPrintscape]

@@GreyGhost-r4z Honestly, most of the time you wont need to mess with the jerk settings. Are you having an issue that your hoping to solve by changing them? As far as the abl, with the bl or cr will work fine. I would get which ever is cheaper when you go to buy.