Massey Ferguson 135 Multipower Removing the Clutch and Flywheel

[@kroghsmachineshop4708]

G'day mate, It's just like I'm standing next to you and we talk about old tractors👍 Saturday morning, lighting up the wood stove, a cup of coffee and a Bundy Bear video while the shed I warming up, not so bad, now it's shed time. Cheers from Henning in the cold north😊

[@BundyBearsShed]

Thanks, It is getting hot over here so a cold drink will do here.

[@robbybachmann332]

Thanks for the clutch rivet lesson Lance. Your area too dry and out our area to wet, a difficult farming here in our part of Canada

[@BundyBearsShed]

It would be nice to have it somewhere between hot and wet eh.

[@gerrygwilson2849]

Thank you sir

[@BundyBearsShed]

Welcome

[@eddytaylor3697]

New sub from the U.S.A. I enjoyed the video mate. Cheer,s.

[@BundyBearsShed]

Thanks Eddy

[@lloydjohnston5382]

maybe you should paint the heads of the bolts white they will be easier to notice for removal enjoy your videos I have 1959 ferguson 4 cyl myself hard to get parts here in CANADA

[@BundyBearsShed]

Yeah probably a good idea.

[@mariusadrian8412]

Hello again Lance,do you think a 12" flywheel would fit masey ferguson 835?thanks for the information.😅

[@BundyBearsShed]

Probably not

[@murdogordon3091]

Do you think my clutch might be damaged as no transport bolts were used when it was removed and it was left lying on its fingers for a good few months?

[@BundyBearsShed]

Shouldnt be a problem at all.

[@murdogordon3091]

@@BundyBearsShed That's a relief. Thanks

[@rosskurtz4507]

Hi Lance, Many thanks for sharing your valuable experience and knowledge.. I am restoring a MF 135, and find your comments very informative. I purchased my tractor with a seized motor but otherwise it is very straight. I have the motor being repaired by a very good local engineer. The big ends had picked up but the crank came up nicely. I heard that there is an updated rear engine seal which a replacement for the wick seal. Is this true? Cheers Ross

[@BundyBearsShed]

Yes Quality Tractor Parts in Ireland sell them, I have some here but I havent had a chance to test them yet but by all accounts they are a good thing.

[@timboothman4888]

I notice a odd spring missing lance

[@BundyBearsShed]

G Day Tim, When they went to the heavy duty red springs they would change the number of springs to suit the HP of the tractor.

[@timboothman4888]

@@BundyBearsShed many thanks I put 6 reds in mine but it had 12 yellows in when I split it. Which is correct?

[@BundyBearsShed]

@@timboothman4888 both could be as the yellow springs had less tension so you needed more. The red you could use 6, 9 or 12 depending on the horse power but it got harder to press the pedal in as well on the smaller tractors.

[@mikaelhaggblom5477]

Have you yet been able to test the lip seal conversion kit? Wondering if it would be worth a try, since our MF 135 seems to need new crankshaft seals. It leaks alot of oil through the weep hole in the bellhousing.

[@BundyBearsShed]

No I have not had the need to use it, I hear they are working well though.

[@irishguy200007]

Lance, if a clutch is put back and the finger bolts are too far forward what can you do with it. Is there a reason they should be depressed forward. I presume they should be level with the clutch front at least but in the case I saw they were depressed far in or forward.

[@BundyBearsShed]

If the pivots are worn they go too far forward but the parts are readily available to replace the parts only and not the complete unit.

[@irishguy200007]

Are these the three small pins holding on the fingers?

[@darrellmullan6105]

What is the bolts size required for holding the clutch in before you remove the outer bolts if you could let me know be very much appreciated

[@BundyBearsShed]

They are 1/4 unc but not sure of the length

[@darrellmullan6105]

@@BundyBearsShed thanks very much for that

[@MphoSekese]

@@BundyBearsShed thank you mate.

[@marten4457]

​@@BundyBearsShed You say it's unf in the video?

[@joelard2716]

So what if you went gun-ho and didn't put the finger bolts in before removing the clutch.......I'm asking for a friend...

[@BundyBearsShed]

No big deal it would be fine

[@davidleesimpson]

Anybody know what the clutch bolt size and lengh are?

[@BundyBearsShed]

5/16" unc but I cant remember the length

[@AfonsoMendesMendes-ht5su]

Bomba injetora cav

[@BundyBearsShed]

Images?

[@irishguy200007]

Makita

[@BundyBearsShed]

Good gear the Makita.

[@elvinsanchez7962]

Primo una preguntita

[@BundyBearsShed]

Thanks.

[@bappitractorhospital]

Good job sir ❤ From India #bappitractorhospital

[@BundyBearsShed]

Thankyou.