Massey Ferguson 65 Part 55 Fitting the Clutch

Hello, I'm Lance (aka Bundy Bear), and doing these videos is my hobby. I do own Queensland Tractor Spares in Australia where I sell parts and offer technical advice to customers.
Parts seen in our videos can be purchased from www.queenslandtractorspares.co...
We have a lot more than we can offer on our web site available to us and in our store. If you don't see what you would like please email [e-mail] or call 1300 850 097 and we will help where we can.
I do try and help with technical advice at [e-mail] if you have a question or are having trouble with your project.
#bundybearsshed, #tractorrestoration, #tractorrepair, #tractorvideos

[@t2lman2003]

Probably watched a dozen videos to understand the principle behind the setup of that clutch, by far, this is the best! Thank you.

[@BundyBearsShed]

Glad you liked it!

[@charleshart6992]

Excellent video - very informative!

[@BundyBearsShed]

Thank you!

[@kt3537]

Great video & detail 🤠

[@BundyBearsShed]

Thank you! Cheers!

[@markfrancis1158]

Just what I needed to know. I have a 165 that is grinding when I try to engage the PTO. Really enjoy the series on the 65, thanks again from Texa USA

[@BundyBearsShed]

Glad to help.

[@manfromthemist1958]

G Day Lance, another great video, loads of good technical info explained beautifully as usual. Barry

[@BundyBearsShed]

Many thanks

[@AaronEngineering]

Very nicely done Lance. Well explained and demonstrated mate. Cheers Aaron.

[@BundyBearsShed]

Thanks 👍

[@noelstractors-firewood57]

Great video Lance. When I had the tea20 Ferguson engine apart a few years ago, I made a wooden clutch disk centring tool before I took the pressure plate of the flywheel. Hehe. Worked great to centre the clutch disk when I put I back together.

[@BundyBearsShed]

Great tip!

[@luzbelito1977]

Thank you very much Lance! That's exactly the problem I have with my MF65, the main clutch works fine, but the PTO clutch refuses to work. So this information is very important. I will try to check those things you mention removing the bottom plate. Thank you very much!! A very grateful MF65 owner from Uruguay 😁

[@BundyBearsShed]

Hopefully it works out for you.

[@kimber1958]

THANKS BOTHER

[@BundyBearsShed]

Thanks.

[@martinnewbery3032]

Hi. Lance. Done that PTO clutch adjustment on an MF many times. An old bit of snapped of hacksasw blade is just right as a gage. Some are a bit strange size bolts, allways have a 12mm spanner handy. Keep up the great vids. Martin. (England)

[@BundyBearsShed]

I think the originals were 5/16 inf but the replacements are now probably metric, I run into that a bit nowadays.

[@paulcole6301]

Nice one video 👌

[@BundyBearsShed]

Thanks ✌️

[@teresabass8314]

I've watched your videos on tearing down pumps and you have helped whole lot I have 6610 Luca cab delphi injection pump dps 8523a100a it's a rotary pump and I'm needing to learn and know about it and fix it need some parts also wondering if you have worked on this type of fuel injection pump

[@BundyBearsShed]

I dont think so, it has mainly been the CAV

[@teresabass8314]

Ok I sure thank you the pump came off of a 6610 ford 4x4 cab series 4 cylinder tractor.sure enjoy your videos thank you sir.

[@johnventura2977]

hey do you have a video on adjusting the clutch on the Massey 65?

[@BundyBearsShed]

No not yet, in the MF135 I did and they are very similar.

[@Shadetreehack57]

Probably a dumb question but if im planing on reusing the clutch do i have to put bolts in it to take it out?

[@BundyBearsShed]

No just unbolt it

[@thorthunder3227]

So the feeler gauge goes behind the hex head bolt? I hear a hacksaw blade is a perfect fit for a guage?

[@BundyBearsShed]

Yes, between the hex head and the plate. A hacksaw blade is around 0.025" normally. Possibly a bit tight but it will work until the plate wears a bit. I like to go at around 0.060" it gives a nice pedal feel.

[@thorthunder3227]

@@BundyBearsShed thanks, i got it done. I had a hard time getting it to buckle up for some reason but finally got that done. Now, i got problems with my governer assembly, i forgot where the springs attached and how the U bolt set. I wish i had a close up pic of that.

[@BundyBearsShed]

There is a video on the governor and setting it up on the TEA20

[@path.of.discovery]

Oh man, I've definitely felt like that fella before with not taking out the transport bolts. So embarrassing. But ya learn something with the screw-ups.

[@BundyBearsShed]

Some of the best lessons learned are the embarrassing ones, I can remember a few.