Your method feels very precise and controlled compared to just dumping it on and squeegee’ing it all over the shop. Thank you.
@the-1st-grimbleahoy Жыл бұрын
Glad I found this while trawling for advice after a glass disaster (strip-off and major clean up) on my own dinghy build.🙂🇬🇧
@johnnydfred2 жыл бұрын
Many thanks to OCH and Russell. Totally inspirational instruction! Make good choices, prepare, and don’t overthink it!
@TTM-GEB Жыл бұрын
THIS IS IT - THIS IS HOW YOU DO IT. I have tried other techniques and then tried it this way... Wow so much better results using just a roller on the dry cloth. One other trick is to first use a dry roller to flatten out the cloth on the boat.
@MrAmpchamp13 жыл бұрын
Thank you very much for sharing your tip on removing the large strand of fiberglass leading the sheet. And thank goodness I've learned this lesson out of sight and under the deck!
@bhtiii Жыл бұрын
Great job of rolling that epoxy out, I learned something about I need to try on my next duck boat. Uncle Ben
@mikesmith8108 Жыл бұрын
Nice clean work. You make it look easy.
@mckenziekeith7434 Жыл бұрын
Does peel ply help with this? If you are going to paint the boat anyway, would you put peel ply over the fiberglass?
@KyokushinKichiKai3 жыл бұрын
Thank you for your demo and step by step self critique as you apply your epoxy. Excellent Sir! Thanks again!
@frederickwood9116 Жыл бұрын
Thanks. Some fantastic things to learn from this.
@StewartGartland4 жыл бұрын
Always a pleasure to watch a master craftsman work. Really great videography. Thanks
@skyak4493 Жыл бұрын
RB, so what is your verdict on the S glass vs the usual thicker E glass? In the video it was well behaved. I have heard complaints S was harder to fully wet. I would think that overlaps and corners are better. S glass makes up for the strength, but thicker might just protect against dents better.
@wyrrie214 Жыл бұрын
Hi, Just watching your great video, did you have to seal the ply with the epoxy resin before wetting the fiberglass on, also did you use the west system epoxy resin for the fiberglassing. the other thing I was interested in knowing when glueing the joints did you have to use an glue before filleting the pieces with the west system filler and resin. Many thanks Michael.
@fisheater844 Жыл бұрын
Your the man Russell
@paulbriggs30722 жыл бұрын
I formally request that overhead fiberglassing be demonstrated!
@blainejeffreys3 жыл бұрын
Ever use a super-super lightweight mist of 3M 77 to smooth out the cloth before applying the epoxy?
@murraythomas92032 жыл бұрын
Is there any particular thickness or type of fibreglass you use and how many layers do you typically put down of cloth per boat?
@ionstefan8402 Жыл бұрын
How does the epoxy resin not hardening to you that fast, and you can still apply it even for more than half an hour?
@AncientScotty Жыл бұрын
This gives you a good bond with plywood? Right?
@tiwie4556 Жыл бұрын
very clean job! Good techniques you're teaching. I'm thinking about dynel sheathing a folk boat, what's your opinion to doing this to a lapstrake construction?
@tiwie4556 Жыл бұрын
I'm worried about solid wood living a little even if the epoxy should seal it and then having the whole thing delaminating. the planking is beechwood so very good absorption of epoxy.
@offcenterharbor11 ай бұрын
There's a lot of conflict surrounding sheathing classic wooden boats, too much to be solved here. I've refinished lapstrake boats before, and just based on that I would say sheathing one would be maddening.
@craigmonteforte14782 жыл бұрын
Beautifull design and execution it would be the perfect motor boat to do the Great Loop in a backwards / Counter Clockwise rotatation IMO why that way ? because you would have following Seas heading south on the Mississippi , no Airconditioning or much heat would be needed. perhaps a Mr Buddy could take the chill off a cool evening ? or a portable Inverter / Generator could run a small space heater that you could Blanket or Tarp the Cabin area off if needed the fuel economy. might even go up a bit ?
@jameseley8972 жыл бұрын
when i put the epoxy i mix in a little bit of sawdust then sand is down with 240 3m sand papper then give it a second coat of epoxy ten put the cloth on
@Zircon_2152 жыл бұрын
Great video! Did you have to sand the pre-coated layer of epoxy before installing the fibreglass?
@fisheater844 Жыл бұрын
Yes, watch more of Russell’s videos
@josephlai97593 жыл бұрын
Thank you for sharing an invaluable lesson, especially regarding the necessity to remove the thick strand at the end. One thing which I have seen other boat builders do is to prime the wood first with epoxy before laying down the cloth. Have you done that already, or your method only require a straight on glassing over? Appreciate your kind reply. Thank you once again.
@shinnosuke1502 жыл бұрын
00:49
@janzahoran98682 жыл бұрын
@@shinnosuke150 please did you noticed which kind of roller he use? Thank you
@shinnosuke1502 жыл бұрын
@@janzahoran9868 It's probably a West System 800 foam roller cover or something similar with a 1/4" nap.
@benjamindemeo77662 жыл бұрын
What do you do to address the extra glass hanging off the gunnells?
@praisebewibble3 жыл бұрын
Thanks for some great tips. Appreciated
@jameseley8972 жыл бұрын
if u want u can put sanding sealer on the plywood first so ur not wasting ur epoxy sanding sealey 5 L is very cheap and u can put fine sawdust in it to make it thicker so it fills up the grain on the plywood
@brandtl14863 жыл бұрын
What part of process does one wear respiratory protection?
@Traderhood2 жыл бұрын
Is it 6oz cloth?
@tommygrngo Жыл бұрын
I wonder if he or anyone else has tried the japanese technique of ‘Shou sugi ban’ prior to epoxy coat?
@Rjtaylor12 Жыл бұрын
Most people say to wet the wood, I'm curious as to why you did not.
@naimanahsap7689 Жыл бұрын
Berapa waktu pengeringan epoxy
@stevetucker25333 жыл бұрын
Is there a need for more layers?
@nateface3 жыл бұрын
Not of fiberglass - this is it for this boat.
@Tumbling_Dice Жыл бұрын
Is this Tally Ho`s tender?
@3Beehivesto300 Жыл бұрын
Is this a plywood boat? Lol I read the description of the video and it said plywood boat.
@wild-radio73733 жыл бұрын
Awesome ♡♡♡ 🤜🏻👍🤛🏻
@ugoroche63472 жыл бұрын
Where are the next videos? Don’t you talk of a série of 10?
@offcenterharbor2 жыл бұрын
You can check out more videos at the link in the description!
@ignatpulya36216 ай бұрын
Never do this!!! The surface must be coated with resin before applying the fabric. Necessarily !!!