MasterLock 175 - How it works and how to bypass with a thin pick.

[@menotel]

I am a new picker with other KZbin tutorials I tried to pick my 175 and it did not work. With your help I was successful thank you for sharing and keep up the good work.

[@AbsoluteRecoil]

Unreal. I watched the video, found some 0.09" shim stock I had laying around, shaped it to aproximate shape and size with a vice and some files. Within less than 20 seconds the lock was open. Great video. I've never picked a lock in my entire life.

[@KENFULLILOVE]

Thanks so much.Your video helped me to fabricate my "tool" and to pick my Master 175d. After I located the the indentions on the wheels, I added 2 to each number. I was fairly certain that I had located numbers on wheels 2,3 and 4 then I started rotating wheel #1 until to my surprise, my lock popped open! Thankks again!

[@stormtacticalconsulting6736]

Great video, best breakdown and Instructional talk through I’ve seen so far! Kudos.

[@rickystart2022]

Thank you Thank you, I've watched tons of other videos and never been able to open this lock. After watching your video I opened it no problem once I understood what I needed to do, thank you

[@EristiCat]

Glad I could help

[@jeremyperry3841]

Yep I agree 100%, I too have watched tons of 175 videos and none actually explained any of it in detail. Thanks so much for the great video!

[@keithwolfe3976]

I tried this on my dinghy lock and it gave me the same combination numbers I thought it was. So I soaked it in vinegar for a few minutes and it opened right up. Now I'll rinse it off in fresh water and use some WD40 on it. Thanks for the help!

[@billmerrick2467]

Great Tutorial. Good job.

[@bondjamesbond1151]

Your entry point helped me out alot I finally got it

[@blainedecker]

Best tutorial. Thank you

[@weeze68dt]

Thanks very much, that was a very thorough explanation.

[@JoBianco]

This really helped me to decode. Thank you.

[@adrianTNT]

You can change the combination without the key if you keep pressing that hole with a tool and align the wheels where you want them. Just the combination needs to be set correctly before pushing.

[@EristiCat]

That's true. The "key" isn't really a key, it's just the equivalent of anything that will fit the hole so you can push the pin sideways. The advantage of the "key" is that because it's got that "flag" on the end you can turn it sideways, and it holds itself in .. otherwise you have to hold your "tool" in by hand.

[@bishop2355]

Thanks!

[@adrianTNT]

1:03 when flat is at that low angle, the notch is aligned so it can open, correct ? Because I kept trying to open it today, keeping my tool in that area and I opened it by MISTAKE (with correct combination aligned) :)))

[@hawgshuggs]

What is the shim called, or its product number from the company yu bought the shim from, please?

[@EristiCat]

@@hawgshuggs I got it from this place. I don’t see it listed separately any more, it’s in a couple of their kits. I’m not sure if it had a name or part number. store.itstactical.com/collections/all

[@MGRRD]

Amazing video. But my luck is already opened and I don't have the key or remember the password. Did you have way

[@EristiCat]

I don't know of a way.

[@zoidelux]

i have a very very old one, were they different in the past? probably from the 70s or 80s, cant get it inbetween wheels

[@EristiCat]

How thick is your shim? The one I use is 0.09 inch. Roughly the thickness of two post it notes.

[@johnhelbig4183]

Where to obtain a pick pen?

[@EristiCat]

I got mine from store.itstactical.com/

[@possumdan1]

how thin is it.....??

[@EristiCat]

The one I use is 0.09 inch. Roughly the thickness of two post it notes.

[@RobertoHernandez-qf4cl]

I have to pick my Lock and have a key but it won’t turn 90° how can I change the combination

[@EristiCat]

You can't change the combo unless you know the existing combo. That's the reason for the notches. If you don't know the combo you will need to watch a video about how to use the pick to figure out where the flats are. When you have found the flats you can get the combo. The only help I can give is that in my experimenting I was able to find the flats for the 3 right dials but not the left dial. So I just tried all ten numbers for the left dial and got the final number. Same would be true for any single dial that you can't seem to find the flat. If you can find the flats for the other three you can just run thru the 10 positions for the last dial.

[@RobertoHernandez-qf4cl]

I’ll try my luck with that. Thanks bud.

[@dmmdmm5435]

You have cats...ah ah choo! Sniff

[@noahway13]

Fantastic visuals. But you are bypassing the hard way. You should get in shallow above the combs and push down, not in deep and push up. You also need to depress shackle.

[@EristiCat]

Using my opened up lock so I could see what was going on I took a look at the angles I was using and as best I can tell I'm only going under the shackle, not the comb. I do agree with you, if you did go too deep it would be counter productive.

[@rodrigopineda4643]

Cuento vale

[@noahway13]

More volume!

[@EristiCat]

Yeah, next time I'll boost it in post-production, or just talk louder

[@noahway13]

@@EristiCat Actually, it was my computer that had sound issue.

[@shaun8256]

Why would anyone bother picking one of those locks is just sad!, those combo locks are so easy to find the combo on its almost laughable. On the other hand they are even faster to simply use 5lbs. and a slight swing of the arm.