Matrix Band - Precontour Interproximal Region - Complex Direct Restorations

[@tongwang344]

After 2 years, finally this guy clear all my confusion of toffimire bands.

[@zaid1234512345]

thank you Mr all things dentistry for making my every day dental practice better

[@rajitharanvijayasekaram5862]

Thank you very much for the demonstration, It's the small things that really matter.

[@kristenackerman659]

This is awesome, most of the offices I work in don't even have sectional matrix available, and it's been a struggle to get a good contact!

[@sunieel408015]

Thank you doc...your suggestions are so valuable!!

[@AllThingsDentistry]

I"m thinking that perhaps wedging will seal off the gingival portion (sorry I didn't place that into this video), and if that doesn't help - there are a few instruments (interproximal carver) that can help during carving. I'll have more of that in a few days. I just posted is an interesting tip regarding customizing wedges from a fellow resident. I can't post links in the reply! Thanks for the comment. Ashley

[@fishribbon]

Thanks, Doc, for distilled info

[@TubesWidener]

Thank you. This issue of the wedge interfering with the natural desired contour usually occur if the wedge hight is protruding coronally too much above the gingival margin, or if the clinical crown is too much short. Ideally the wedge should be not protuding too much coronally after being wedged tightly so you will have enough clearance in interdental triangle area to perform the matrix burnishing and contouring. So how to get to this ideal wedge is by 2 main strategies: 1) By "removing" the excess wedge which is coronal to the gingival margin by large round carbide or by large spoon excavator (excavate in one direction to avoid dislodging the wedge). Then you just move the wedge out a little just to allow your matrix to slide in then tighten the wedge again. 2) sometimes you have to remove (excise) a lttle of interdental papilla to to allow the wedge contact to tooth to be more apical to your gingival margin.

[@acash93]

All your solutions will cause lots of bleeding though.

[@puttaanjaneyulu3735]

Or something called anotomical wedge

[@patmo141]

Cool vid, I wonder if you could use SSC contouring pliers to tuck in the gingival and bulge out the contact more naturally too.

[@yashar350]

thanks Dr❤️👍🏼

[@drhakimvaaand2936]

hi dr nice explanation what's the reason of burnishing matrix?

[@fathima8953]

Sir, how to prevent gingival laceration during matrix placement.

[@staver76]

What do you think of this vs a dixieland precontoured band?

[@jonathanwirth3420]

Are those guitar strings sticking out of that tooth you're restoring?

[@drabhaprasad8684]

Thank you...

[@al6450]

Thank you

[@erodoeht]

Hi Mark thanks for the tips. Just wondering though, after burnishing as such, how do you deal with the possible issue of knife edge overhangs that may result because of the curved matrix?

[@lauralove3162]

Manicure 💅

[@vilelaclaurevilelaclaure4547]

thanks for recomend

[@skdavidnba]

thank you!!

[@yuia111]

thx a lot, this is useful!

[@mukeshadwani4695]

Thankyu sir🙏

[@EdKendrickDDS]

emergence profile

[@dr.danielespinel1690]

easier make it outside the patience mouth that give de contact forme with the matrix inside the mouth. thanks a lot. :-)

[@terrenceshaw8397]

You don't need pins with composite if you are bonding to dentin and enamel. Waste of time and completely unnecessary in my opinion!!

[@user-en3tx3zu3j]

In the video he said its for an unrelated amalgam video.

[@dongdongdong8413]

Thank you