2AZ-FE 2.4L Engine Rebuild||Head installation Balance shaft installation ||Timing Chain installation

[@egoillusion5734]

I have a Camry AZ engine 2005 I watch your videos n.learning from it im not a mechanic but now im getting confident in.learning n doing this in case of emergency lol thanks man keep it up new subscriber

[@MayoCarsDR]

Ok, thanks for comment and watching video

[@SwithenMahemu]

I love the way you assemble the engines..l admire your work... please continue l wish to have my workshop like yours

[@MayoCarsDR]

Thanks for comment Where are you located

[@shadowdragonmusic9419]

I have a 2004 Toyota Camry with this engine. 115,500 miles strong. It absolutely blows me away how simple these little motors actually are.

[@ahmadghosheh3104]

The head bolt torquing looks worse that it actually is. I did the head gasket and really went smooth, the 70 NM isn't too much and 90 degree is not bad. I was worried at first but after 2 bolts I just went right through them

[@Maxaction607]

Nice job keep on updating

[@senolbilici6403]

kolay gelsin ustam videolarını beğenerek izliyorum çok bilgilendrici ve öğretici Türkiyeden takip ediyorum sizi benim iki sorum olacak size 2004 model toyota corolla e12 hb aracım var araç çalışır vaziyetteiken özelikle ilk çalıştırmada görültülü çalışıyor 15 veya 20 saniye sürüyor sonra normal çalışıyor neden olabilir aracım benzinli birde hararet ibresi birden döşüyor ve araç kendi kendine gaz veriyor ilginiz için şimdiden çok teşekkür ediyorum

[@keithdickson2560]

I have the same motor in my Toyota Camry LE 2004 and it only has 84,505 miles on it right now and I purchased the car from Auto Lenders in Williams tow N.J. and it only had 65,000 miles on it with one owner and well maintained and I maintain my car very well the only thing I needed to do to it was change the water pump & the idler pully. When the mechanic did the Joe he told me what he was going to do.Now I am have slot of knowledge on what needed to be done. I told he when he changes out the parts to also put new pulls on both water pump and idler & the new shock on the idler pillow cause I know when you buy parts it doesn't come with everything you really need to do the job right. He was going to re-use the old pulls I told him I want new ones ,because sure as High or He'll once he puts it all back together the pulls will go bad! I know because the pulls have bearings in them also, Not only that the parts were only $35. Each. Now I don't know, Well I do know why they don't come with all the parts when you order them. They just want you the average person who doesn't know to have to come back after a month or so when the job was done you have to go back.😉

[@MayoCarsDR]

Thanks for comment

[@sulekhajaan9807]

شکریہ اللّه آپ کو ہمیشہ خوش رخے

[@MayoCarsDR]

آمین جزاک اللہ

[@Sirob1969]

hi Mayo Cars. this engine doesn't need water spacer jacket in the block?

[@MayoCarsDR]

water space Jacket is not available on all models, some have it and some don't

[@SsengoobaIvan-qp7cm]

soo massive thanks a lot bro what a good job

[@MayoCarsDR]

Thanks for comment bro

[@ephraimvynnemapwashike3687]

I got a 2002 model and I put terminals vice-versa and it starts bt no throttle, any advice guy?

[@MayoCarsDR]

If there is no problem, it is fine

[@glenglene8473]

there are two set of balance shafts. do you know the difference between this set (13601-28021 & 13602-28020) and the set you used?

[@MayoCarsDR]

Both of them are same

[@haroldhoupt6090]

On my 2002 2.4 L Camry. When I dropped the oil pan I found 2 balance shaft bearings laying in the bottom of the pan. How could the bearings work their way out to fall into the pan?

[@ehabradiology]

They are above each others

[@66designs37]

Hello friend, may I ask why new balance shafts were used?

[@MayoCarsDR]

Because the old balance shafts were bad.

[@russellhowe1937]

What sealant did you add on the corners of the head gasket? Do I have to? If so will black rtv work?

[@MayoCarsDR]

Yes

[@MayoCarsDR]

The same silicone you apply to the timing chain cover can be applied to the corners

[@vitaliy6605]

Собрал без герметика, всё отлично работает! зачем он нужен, не пойму? Нигде нет такой информации.

[@YudaMutampuka]

Thanks very much for your help

[@MayoCarsDR]

You welcome dear

[@kingsleyobon7505]

If the balance shaft is not fix properly and is making noise when u are driving the car , will it affect the crankshaft

[@MayoCarsDR]

Yes

[@MayoCarsDR]

This will be dangerous for your engine

[@SirajulIslam-ho5vs]

ভাইয়া গাছকেটে গাম কিসের লাগি দিলায় ❤❤❤

[@arunayuven2102]

Nice job

[@MayoCarsDR]

Thanks for comment

[@firstlineinspections7225]

Thanks for an awesome video.

[@MayoCarsDR]

Thanks for comment

[@keithdickson2560]

Why didn't he put the sealing all the way around the block gasket before you put the head on ? 🤔

[@MayoCarsDR]

I have applied silicone where it was necessary and nowhere else

[@allbanglatruthnewes1775]

Thanks

[@MayoCarsDR]

You welcome

[@ChukwudiJohnson-ut5oo]

Lovely job

[@MayoCarsDR]

Thanks for comment

[@mickypie5892]

Very good

[@MayoCarsDR]

Thanks for comment

[@felicity2054]

This is lovely

[@MayoCarsDR]

Thanks for comment

[@shekharviswkhrma4201]

Thanks 👍

[@MayoCarsDR]

You welcome

[@dariostaboua3178]

Good

[@mohammadtkhan5879]

Excellent

[@MayoCarsDR]

Thanks for comment

[@fabiansantos4558]

It didn't show when you released the tensioner.

[@MayoCarsDR]

15:00

[@keithdickson2560]

I forgot to proof read my last entry. Sorry, you got the idea.😉

[@MayoCarsDR]

Thanks for comment

[@ابومحمد-ف9ث3ص]

جيد جدا

[@gebremikaelhagos7988]

🙏🙏👍👍👍

[@remidiusmchafu9245]

Mbona ujaweka sheraki

[@deven6518]

I fear removing the head of this engine. Stripped bolts are a thing

[@MicahGobara]

Mark 2

[@iddrisualidu2703]

Salifu Ussif

[@lovapal5495]

হাই

[@tyyu5271]

Corolla xrs engine

[@Maxaction607]

Nice job keep on updating

[@MayoCarsDR]

Thanks for comment