Enter diags mode by pressing any button for three seconds, release three seconds (and repeat). As you can see, there are no error codes.
Пікірлер: 28
@dirty_porter_reekin3 жыл бұрын
Thank you sir. You just saved a wrench from going through a wall.
@jaysonthomas6304 жыл бұрын
UL code problem is from continuously putting in unbalanced loads. To fix it, turn on its side and tighten bolt in the middle of bottom, if lose. If not lose, take out bolt to probably reveal a cracked rotor or broken sensor. A couple good video on line that shows how to do it, It's not to difficult.
@cynthia199004 жыл бұрын
It worked for me! Thanks for the info :)
@mrclyde19963 жыл бұрын
Waaa I don’t have a Maytag bravos xl washer just a dryer i did have a washer and it’s gone waaaaa
@BarryHarrellYouTube4 жыл бұрын
The test never runs on mine. It powers on and runs (dryer) and blows cold air out of it. There was some junk in the exhaust tube, but not enough to cause any issues. Anyway, it just stopped heating and the self test will not start. Three second hold, three second off, repeat three times (and saw to do it four times in one video). The fourth press changes the diagnostic test, but it won't run on mine either way. Never really like it or that stupid washer that uses so little water that it has to be run twice some times. Thanks for posting the video though.
@TheWASHINGMACHINEBOY6 жыл бұрын
cool it works even if the machine is turned on
@tonymcrae65105 жыл бұрын
My agitator ain't working. Help
@vanessadraper41523 жыл бұрын
How to fix (du) code lid lock ?
@denialopez923 жыл бұрын
This washer does not spin. The code F72 appears
@ivanmarquez30956 жыл бұрын
How do you know if there is an error?
@jdbbs13 ай бұрын
Mine stops and says F32orF71 after I had a power surge . Not one problem in 12 yrs 🤦♂️ what did you end up doing and the washer lol
@vond74954 жыл бұрын
Two questions.....1) How do you recalibrate a newer model Maytag MVWX700XL2, after replacing the actuator (It shows the error codes on a digital screen). I can't seem to find instructions to recalibrate a newer Maytag after a repair. 2) I've done everything to remove my Maytag Bravos XL washer pulsator (some call it a washer plate)...it won't budge. It raises up about 1/2 inch and seems to hit something, like it's locked in place. I want to check for coins that may be stuck underneath. I don't know what else to try. I tried turning it from side to side, as if it's washing, but it won't move back & forth either.....not sure if that's possible with the power off. What could be the problem ??
@efrainperez78992 жыл бұрын
Dígame cual es la falla. Cuando aparece. Herror f50
@maditaglez83822 жыл бұрын
Ola porque aparece la frase de DU
@laquindabutler49645 жыл бұрын
This washer is tripping, I've had it now about 5 years, it isn't one that I would recommend. Of course, my extended warranty has expired..... I keep getting the UL code I've done all I can. I have this exact washer.....Don't waste your money.
@ScantPear3 жыл бұрын
UL means unbalanced so you need to let it re balance itself or if not re distribute the clothes and if that does not work, replace the suspension rods
@lillianabottsalcorta82735 жыл бұрын
Say something durning your video please
@markgallant31245 жыл бұрын
Sorry. Not much to say. I put in diags mode to prove to a potential buyer that it was functioning properly. I decided to leave the video as a starting point for people who are having issues. I also thought it was cool to be able to run the washer with the lid open.