Mazatrol Programming Workpiece #1 Mazak T2, T3 Control

Mazatrol Programming Workpiece #1 Mazak T2, T3 Control

[@Peter-zw8yn]

Thank you for these, I'm a cnc apprentice and currently work between fanuc, mori seiki and also mazak machines, there aren't as many people competence in teaching mazak programming so these videos will be of great help.

[@mazatroltipsandtricks6816]

Thanks Peter.

[@allandesoer7672]

Thanks for the video. It brings back happy memories of before I retired. I ran and programmed a Mazak Quick Turn 28 T32 for 15 years. Lernt all the shortcuts going from Mazatrol to G codes and back when appropriate. Oh Happy days. It was a brand new m/c and 4 of us went down to the Factory to be trained in programming in thee Midlands UK. After watching these videos To refresh my faded memory I think I could walk back onto the m/c after 20 years and carry on as no time had passed. I must be a Nerd for getting hooked on these videos. My little c/lathe isn't the same in retirement.

[@mazatroltipsandtricks6816]

Thanks for sharing Peter.

[@christophercolumbus8944]

any experience with fusion 640? did you ever bother to define chuck or jaws calue in SET UP INFO page?

[@alerosh]

Thank you very much for your work and sharing your knowledge. You are one of the best Mazatrol machine teachers on the Internet (and maybe the best one). Good luck in your business!

[@mazatroltipsandtricks6816]

Thank you!

[@Captain_Hapton]

Thanks so much. Just started as a CNC machinist on a mazak t plus and I have to set up and program a piece on monday as a test. The guy training me is good but not a very good teacher, or hasn't had the time to give me enough hands on training yet. Been surface grinding for 3 out of my five days so far, so this was a big help setting up a basic program. Thank you!

[@mazatroltipsandtricks6816]

Cool. You're welcome.

[@carneeki]

Oh man I wish I discovered your channel 24 hours ago! I just did my first Mazatrol T-Plus program (and also my first lathe program!) with guidance from the boss. Watching you do the Z-offset suddenly makes a lot more sense now. I'm going to have to spend every spare moment I have watching your other videos now :D Thanks heaps!

[@mazatroltipsandtricks6816]

Cool. Glad to help!

[@colleenp3484]

Thank you for sharing. Its my 3rd week into learning CNC and this video is very informative.

[@mazatroltipsandtricks6816]

Glad it was helpful.

[@bobtrendz3863]

Nice explanation thank you! But please try to focus the camera on the screen very close because it's hard to see and figured out what is written there thank you.

[@joedunne1134]

Hi nice videos. A good tip i always do is after setting your z zero ,look in your programme for the furthest z position .I then manually traverse the tool off the face & to a safe distance off the outer diameter of the part ,then traverse it manually to the furthest position it will go to in Z (checking the position on the display) to check that the tool will not crash into the chuck or alarm out on the chuck barrier. Has served me well over the years. Would you be able to do a video on fixed & floating head tapping please ?

[@mazatroltipsandtricks6816]

Yes, I do that too, but haven't shown it on the videos. Good point. I can do floating tapping, but my old machine does not have rigid tapping capability.

[@joedunne1134]

@@mazatroltipsandtricks6816 Thank you .

[@djenii2020]

Спасибо за обучающее видео, коллега.

[@emilgabor88]

Grate explenation. probably one of the best videos i have ever seen for a cnc controler.

[@mazatroltipsandtricks6816]

Wow! Thanks for the compliment.

[@giddyupbo]

Hi Phil. I have what I think is a good idea for a video for you to demonstrate if you’d like. I think there are a bunch of new machinists out there that would love to hear how you would go about tackling this process. I’m interested in seeing you demonstrate how you would create a 90° groove on the face of a part. What tool you would use, and how you would go about programming it to get a nice groove with a nice finish and no chatter.

[@mazatroltipsandtricks6816]

Thanks for the idea Brian. Face grooves are definitely something I need to do.

[@r3FMusic]

Thanks for video..

[@tuner453]

Thank you for all in formations tips and tricks , You are awesome! I cant wait to see the next video how you program Live tooling Mazaktrol.

[@mazatroltipsandtricks6816]

Thanks! Live tooling is on the list. I'm just getting started so please be patient for it.

[@yabetseasgedom9365]

Thanks for sharing your experiences good job

[@mazatroltipsandtricks6816]

Thanks for watching.

[@ozguraytekin3800]

thanks a lot. (TÜRKİYE)

[@mazatroltipsandtricks6816]

You're welcome.

[@chrisn3794]

Thank you so much! We just acquired an old mazak quick turn to in our tool room can’t wait to use it now super easy programming

[@mazatroltipsandtricks6816]

You're Welcome. Mazatrol is actually fun to learn.

[@chrisn3794]

Mazatrol Tips and Tricks do you know anything about sub spindle mazatrol?

[@mazatroltipsandtricks6816]

@@chrisn3794 I know some sub spindle stuff because I use it on our Integrex but I cannot demonstrate it on camera because I don't have one at home.

[@chrisn3794]

Mazatrol Tips and Tricks I started trying to learn the machine today. Had an issue setting a small p horn boring bar with the tool setter the bar was off by like 10mm or so. Manual setting it off a predrilled hole worked. Any idea why the od tools set correctly of the tool setter but not the boring bar. Also the machine is in inch I changed a parameter that made everything change to mm but when trying to run the program the numbers weren’t correct.

[@mazatroltipsandtricks6816]

@@chrisn3794 You cannot simply switch a Mazak over from inch to metric like a Fanuc. You have to change a BUNCH of parameters to make the machine function correctly.

[@giddyupbo]

I’m having trouble programming a full circle face groove using mill line center with a 90 degree chamfer tool. I envision ramping the tool in at the starting radius and just walking the c axis around. Seems simple lol. I can get it to go 180 degrees, but not any farther.

[@mazatroltipsandtricks6816]

Try programming it in 90 degree increments.

[@weldmachine]

Just found your channel looking forward to follow along. Keep up the good work. Love the MAZAK machines so much at the moment completely rebuilding one as i have time ??? Can not justify a Brand New machine so i need the next best thing, LOL. Rebuilding a QT15 1990 model with a T32-T2 controller. Thanks for posting. Regards Peter.

[@christophercolumbus8944]

do you happen to have post processor? for EIA?

[@weldmachine]

@@christophercolumbus8944 IF your asking Me ?? I don't have a Post for EIA. But you might need to be a little clearer on What Post you need to suit what Software ?? Different Post suit Different Software. Eg : Solid Works, Fusion etc

[@christophercolumbus8944]

@@weldmachine masterCAMo , sir

[@christophercolumbus8944]

i am not even sure how EIA ends up generating codes you know how with fanuc you have G28 U0 G28 W0? or always G20.... only M3 no gear change while in okuma (M3 M42 you can have ton of M codes in one line) with Fanuc end with G28G91X0Y0 G28Z0 M30 (end rewind) as opposed to (M2 okuma) is it the same with Mazatrol EIA?

[@weldmachine]

@@christophercolumbus8944 I can't say All ?? But most who run Mazak 2 & 3 Axis Lathes. Usually they run these machines in Mazatrol Mode. Same for me unfortunately. So i am no wealth of information on this subject. But i understand your question about the Codes. IF in EIA Mode the Mazak Machines Should run ISO / EIA Codes with out to much trouble ?? But maybe i am assuming too, LOL. I am Assuming because it's the same when i use a Siemens Controller in ISO Mode. Not sure what part you are trying to create also. And IF you are trying to do this on a Lathe or a Mill ?? Assuming again. Lathe ?? Not much that can't be created in Mazatrol Mode. I guess most of what i am writing is not much help as most of this you already know. I wish i had the right answers for you. But i am limited by my previous experience with different Controllers, and some of it you forget too, LOL

[@danb8759]

I have a qt 15 t32-2 could u do a rigid tapping program pls , ps you have been so much help I just got machine a month ago

[@75kGa]

Just learning mazatrol so great videos thanks. One question. Would you happen to know, is this mazatrol principal that you are demonstrating the same that would found on the new mazak machines with the smooth controls?

[@mazatroltipsandtricks6816]

The Smooth controls are very similar to what I am showing here even though this machine is 30 years older. The biggest differences with my machine and smooth control is the tool description in Smooth is placed inside the program vs just calling up tool 1 for example. Also, the work shift is also inside the program instead of on the tool file screen. The basic language is the same. I had no trouble learning the Smooth control on the Integrex.

[@majster_kesz]

Super Teacher ;) Sub

[@mazatroltipsandtricks6816]

Thanks!

[@user-nb9wq9ow4o]

Phil you are cool!

[@mazatroltipsandtricks6816]

Thanks for the compliment!

[@jeffreyschmiedeck4254]

I would like to see a video of Machining a casting.

[@HIENTRAN-ze9ju]

Thank you for great video. At my work have Mazatrol 640 . I don’t know why I could not edit my mistake program. I could not use arrow left or right . I mean no matter what I put left or right arrow it go to next row ??

[@mazatroltipsandtricks6816]

You have to be in edit mode to edit the program. To do that you push program soft key and it will allow you to edit the program.

[@hienaz723]

@@mazatroltipsandtricks6816 thank you. I will do it on Monday. Im normal run program with G code . This is my first time do program with mazatrol so im a little bit worry. How do i know my tool set correctly like tool will rapid to z1.0 so i can visually know my tool set right.

[@mazatroltipsandtricks6816]

@@hienaz723 If you want the tool to clear the face by 1" then add 1" to workpiece length and add 1" to stock face on first line of the Mazatrol program.

[@hienaz723]

@@mazatroltipsandtricks6816 i run in the middle program then insert break how can i start where it were rather then start from begin program thank mazatrol 640T

[@mazatroltipsandtricks6816]

@@hienaz723 Watch my video about TPS button.

[@mtnbikeman85]

This makes me want a mazak so bad. Learning an old 6t-b fanuc ikegai at the moment (no g54 even... just g50)

[@mazatroltipsandtricks6816]

Thanks. Just so you know, you can enter wear offsets on the old Fanuc 6T on the geometry page by inputting U and W values. This will add or subtract from the geometry. For example, W-.001 will change the geometry by .001". I do not remember if U values will change on diameter or a radius though. What I mean is U-.001 might change the diameter by .002". Check it to be sure.

[@mtnbikeman85]

@@mazatroltipsandtricks6816 thanks, keep up the good work. Mostly just saying that mazatrol looks so much nicer and more user friendly for something developed at the same time.

[@mazatroltipsandtricks6816]

@@mtnbikeman85 I agree 100%. It's amazing what this 34 year old machine can do!

[@ahmadabohamida6686]

hello i have a question please, i have a mazak lathe, when i turn a long shaft for example the length is 500 mm now when i measure the shaft in front i have for example 60 mm diameter and in the back i have 59 mm diameter. do you have any idea what causes this error? and the error causes a lot of problems when i drill vertically on a cylinder surface in this case i get sloping hole my machine is also quickturn thank you very much for your help

[@mazatroltipsandtricks6816]

Your tailstock is out of alignment.

[@ahmadabohamida6686]

@@mazatroltipsandtricks6816 but if I work without the tailstock, the turret moves at an angle, I tested it with a dial gauge

[@MrMunch1]

Hi I have an issue when I clamp my spindle the spindle clamp light stays on unclamped, I have tried altering the sensors on the back of the spindle and it makes no difference the spindle stays unclamped

[@mazatroltipsandtricks6816]

Spindle only will clamp when C-axis is engaged.

[@MrMunch1]

@@mazatroltipsandtricks6816 when I engage c axis it changes to Milling mode and the clamp light stays on unclamped

[@MrMunch1]

@@mazatroltipsandtricks6816 I get 2 alarms 173 auto start cond insuffi (prot 273 start cond err ext feed hold

[@MrMunch1]

@@mazatroltipsandtricks6816 I think one of these alarms is because the spindle won't change to clamped

[@braaapscallion7245]

great channel ! we had our drives replaced and ever since m8 wont cut the coolant on' also the chip conveyor wont stop unless you cut the machine off. ive looked in the parameter book and cant find anything about these . Any suggestions ? Thanks

[@braaapscallion7245]

quik turn with 640 controller

[@mazatroltipsandtricks6816]

I have no clue what is wrong on your machine. Thanks for the compliment about my channel.

[@hendraezzo424]

hi , do you know how to create taper thread on mazatrol quick turning

[@mazatroltipsandtricks6816]

Yes, taper threading will have different values for X dimension whereas straight thread has same value for X.

[@hendraezzo424]

You have example, I’m writing different point but the result its straight thread

[@mazatroltipsandtricks6816]

@@hendraezzo424 I need to make a video on tapered threads.

[@hendraezzo424]

Yes please, I’ll be waiting the video

[@cncsolution_Bajio]

Hi,. Do you have a mazatrol T1 programming manual? buy a QT10 Universal cnc lathe. but I don't have information to operate it

[@mazatroltipsandtricks6816]

I do not have a T1 manual

[@user-tm7mw4kp6v]

Phil, thanks for the video. Tell me how to change the language in Mazatrol? Everything is displayed in spanish)))

[@mazatroltipsandtricks6816]

I do not know how to change the language.

[@kpmadness]

How do you know to choose between Mazatrol and eia?

[@mazatroltipsandtricks6816]

Some machines do not have EIA option. EIA was an option from Mazak but later on, they made EIA a standard feature. EIA is G-code programming.

[@romanorolex2325]

Do u by any chance offer tutorials over mastercam

[@mazatroltipsandtricks6816]

Nope. I do not own a seat of MasterCam.

[@Mohammadali-ve2fb]

Sir how to cut in program parts??

[@mazatroltipsandtricks6816]

If you are asking about how to make parts and then cutting them off a bar, I have a video on that subject.

[@knuddelbaer35]

Mazatrol ist 30 Jahre zurück gegenüber anderen Werkstattprogrammen 🤫