Mega Brand Dancing Pole Installation Guide

[@drenched]

I have 2 different flange nuts and am not sure which goes where, and which side for each needs to face up. This video doesn't give a closeup so I'm still not sure. Could you please describe or link to a diagram? Thank you!

[@drenched]

So i think the nut with the indentations to fit a wrench is the BOTTOM one, and the indentations face up.

[@rasstylediary2402]

My pole is constantly slipping and when it’s not slipping it’s not straight this is the worst pole. I’ve had other poles setup in the same room and they didn’t budge

[@jannettparris9077]

the top is stuck, how can i get it to come off?

[@cottoncandy6000]

Mine keeps going in towards the ceiling, the flange lock nut keeps coming loose when it spins causing cracks in the ceiling . What can i do?

[@CarlinaHolliday]

Mine as well

[@Kaleidoscopekitty0920]

What size screws r the ones in the pole cover? I lost them!

[@angelphonics]

4:53 ugh!! "lock the flange nut down" without showing where it ends up!!! ugh!! why cut that out?? what does that even do?

[@thecuteshuttletransportati7025]

How can I remove my pole? I've had it up for 8 months and I can get the dome to detach from the ceiling please help!

[@cinupd]

Loosen the Flange nut on the black height adjuster, about half way up and then use the long stick insert it in the hole on the height adjuster so you can lower the black height adjuster down.

[@MsP0le]

@@cinupd hi i am having trouble getting mine down as well. I have loosened the flange but when i insert the stick through the holes on the black pole bit the whole pole just turns and the dome isn't loosening..am i doing it wrong?

[@cinupd]

@@MsP0le First step you need to do is to put the pole in the non-static mode you need to lock the pole first from spinning. After that is done when you insert the long peace into the little hole you should be able to turn it down. Make sure to loosen the flang nut. If the black height adjuster is stuck you can spray some WD-40 to help loosen it up

[@Mypinkpixie]

My pole is on static put when I go to loosen it the adjuster doesn’t move but the rest of the pole loosens instead making my pole stick to the ceiling more 😩

[@leahrayher8259]

Cannot get my pole down for anything, the pole became crooked when is use so now it’s not coming down at all even tho we followed all the instructions :(

[@Idkabout5myname]

It's making "cracking" sounds if I use it with spinning... Is it the same with yours ooor?

[@sammysixx9076]

That was happening to me too! I just ended up loosening my pole and tightening it again and that cracking sound stopped

[@takoyakitarot]

I unscrewed the bottom two screws to allow my pole to spin. It spins, But with mucu resistance. Is it because the pole is new? Is there something I can do to gwt the pole to move a bit smoother? When I spin it, It's almost like it snaps back to it's original static.. Any ideas?

[@sinamen516]

try unscrewing them more, I had the same issue

[@takoyakitarot]

@@sinamen516 Thanks, I tried doing that and it worked!

[@sinamen516]

@@takoyakitarot oh great!

[@Yorkielover941]

My black thing is all the way off and there’s no way to get it connect

[@1creativeillusion]

Any suggestions on how to prevent ceiling damage? I’m “following” instructions, but I’m doing something wrong because I’ve put a hole in the ceiling every time I use it.

[@adrianflo6481]

Not using a shit ceiling? putting such an extreme pressure will cause problems no matter what you do. you are literally installing a jack hammer and then budge it with your whole weight. that being said. try and identify where the supporting beams in your house are and mount in directly under one. that will help.

[@drenched]

Use a stud finder to make sure you put the dome fully centered on a joist.

[@nafnydesign]

Before screwing on all of the extended poles make sure you even need all of them. All 3 pole extensions wasn't needed in my home I wish this was instructed prior in the video.

[@Mang046]

I have a extra spinning circle piece and I’m not sure where it goes. I put the whole pole up and realized it wasn’t a smooth spin so I need help figuring where it goes. Please help

[@nathaliasanchz]

eeshtoni hi did you end up figuring it out?? I have the same problem. It’s not spinning smoothly

[@Mang046]

Nathalia Sanchez no I didn’t, :( I juts still use my pole. When you spin on it, it doesn’t feel bad.

[@nathaliasanchz]

eeshtoni I’m having trouble uninstalling it now :(

[@Mang046]

Nathalia Sanchez have you watched the video?

[@nathaliasanchz]

eeshtoni yes and it’s not help :( my pole is stuck

[@tamaraolivaaraujo7127]

Just received my pole and have some problems putting it up. The height adjuster doesn't go all the way down, it goes down only a few centimetres then it gets stuck... Can it be there's a problem with the thread?

[@cinupd]

Try using some wd-40 and make sure to loosen the flange nut also.. please email me at [e-mail] With pictures will help

[@ziviaberkowitz8113]

@@cinupd I'm currently having the same problem setting up my pole that arrived today

[@Najerai17]

I like how you demonstrated how to install and uninstall

[@nathaliasanchz]

Why isn’t my pole spinning smoothly around? It’s a bit rough when it’s half ways spinned. Please lmk!!

[@Idkabout5myname]

Do you still have the problem?

[@kyzerbobyzer7053]

My height adjuster wont raise at all to fit my ceiling! Is it just stiff or broken?

[@kenighall]

You need additional extensions to lengthen the pole.

[@emilybrown1287]

Worked almost perfectly with these directions, except it says to attach on flange nut towards the end and totally skips the part where she had attached the other flange but already, so I had to take the entire top back off to add the second flange but in order to screw the cover on smh

[@theshanman8124]

So my girl is freaking out, we took down the whole thing from the ceiling but the two main poles are stuck together, now how can I get them unstuck and come back into two parts?

[@cinupd]

you can try to use wd-40 and spray it between the poles, then use the long stick it came with insert to the hole on pole and twist it out

[@theshanman8124]

Mega Worldwide I bought the thing from a buyer on an online app and she told me it didn't come with no tools. Is there anything you would recommend like an Allen key or something. Where do they sell them at specifically?

[@sinamen516]

my pole keeps slipping from the ceiling smh. it was fine in static mode but the spin mode makes it slip

[@cinupd]

Your pole is not attach correctly to the ceiling beam.. using a stud finder to locate it.

[@acrylicpourerer6992]

How do you deassemble it 😓

[@drenched]

This worked for me: 1. Take off the height adjuster cover. 2. Spray wd40 on the flange/height adjuster if needed. 3. use a wrench to loosen the bottom flange nut to make it spin UP the height adjuster (use a real wrench, the pretend one included bent 😅) 4. Use the stick thing to spin the height adjuster DOWN into the rest of the pole. Looking up at the ceiling, that means spinning the stick COUNTER CLOCKWISE. Eventually the pole will shorten enough that you can angle the dome out and lay the whole pole down.

[@elizabethshavers756]

How do I loosen the top lug nut? It's not budging .

[@cinupd]

you can spray some wd40 and use a wrench to help you loosen it

[@thebestshow8153]

@@cinupd i have my pole up and the lug nut is stuck at the top rim of pole. Itwont let me loosen to remove.im geting ready to move how can i remove this

[@cinupd]

@@thebestshow8153 first did you put the pole in non spinning. Did you try spraying some wd-40 and you can use a wrench to help loosen it. Please email me directly [e-mail]

[@drenched]

@@thebestshow8153 WD40 + use a REAL wrench - not the one included in the toolkit that just bends if the nut is too tight.

[@NeciaSoGeEkie]

How do you uninstall

[@cinupd]

you can order from our website or you can use a screw driver that fit in that hole and twisted off. www.megabrandonline.com

[@theshanman8124]

Mega Worldwide what would be the easy way to do it, just set up the pole then twist it off with the screwdriver?

[@cinupd]

You can try that, to see if it works.

[@theshanman8124]

The screwdriver thing didn't work. I even sprayed lubricant on the poles and they still don't come apart. Is there another way? What about rubber mallets?

[@BREO625]

No one shows what to do when that black pole doesn’t pull/screw through. Now I have a useless pole .

[@yellaboiiswagg7589]

Right! Im having the same freaking issue

[@BREO625]

Yellaboii Swagg i was able to have a replacement sent to me, but trust i know your pain.

[@yellaboiiswagg7589]

For free? I ordered mine from wish so i highly doubt I'll be able to get one. Where did you get it so i can try and order me one?

[@BREO625]

Yellaboii Swagg lol yes for free. I ordered on eBay. The seller is Reasejoyus hun.

[@yellaboiiswagg7589]

@@BREO625 Thanks Love!

[@vaholathevegan8987]

please speak in tutorial videas..visually kmpaire cant see well but thanks for uploading..

[@wskirstenkarr5391]

That's for making both an install and uninstalled!

[@cinupd]

Please email me directly with pictures of issue. Email will be answer with 24 hours exclude weekend. [e-mail]

[@nicoleperigrino740]

is the mega dance pole a good dance pole for home use ?