Mercedes-benz W204 Baglygte blinklys reparation / Tail light LED turn signal repair

Der er opstået en løs forbindelse mht blinklyset. Det virker lidt efter et par klap på det men så fejler det igen.
LED Blinklyset kan ikke pilles ud uden at glasset forsigtigt pilles af ved limningen.
Brugt originalt koster omkring 1500kr, Nyt uoriginalt koster det samme, men der skal så købes to for ellers vil den ene være pæn og den anden ridset.
Jeg prøver at reparere det. Det værste der kan ske er at det ikke kan repareres eller ikke samles og så skal der ligemeget hvad købes nyt/brugt.

[@mohamedbouajaj3321]

Besten Dank meiner Freud 👋🙏🙂

[@sawomirwoosiuk9137]

this way works very well, use a wide screwdriver to pry slowly until you hear a small crack and continue 1cm . only slowly. Two sides lengthwise, then bend slightly and it will go away - it will break at the edge. thx

[@studio-relaxingsounds2685]

With what did you glue the lens back on the tail light unit?

[@YasinHarmann]

Pattex - no more nails transparent

[@M1ROSLAV96]

Was ur tail light blinking?

[@M1ROSLAV96]

Mine problem is that my tail light is blinking

[@YasinHarmann]

No, mine was dead.

[@M1ROSLAV96]

@@YasinHarmann okay thank you for information.

[@oRuisuu]

How did you take apart lens with a dremel tool ?

[@oRuisuu]

Or what tool you used

[@YasinHarmann]

Just a big flat screwdriver that still fits in the gap and twist.

[@YasinHarmann]

You break it little by little

[@MarcinStefański-j7q]

[@ramizday3741]

hi. how can i open my taillight glass?

[@YasinHarmann]

Cam ve kasa eritilerek birlestirilmis. O birlesim yerinden büyük bi düz tornavida ile ufak ufak kirarak actim ben.

[@ramizday3741]

@@YasinHarmann hocam kırılınca nasıl oluyor peki birleşme olayı. Yapıştırılınca geçiyor mu? Ya da harbiden videodaki gibi kırayım mı?

[@YasinHarmann]

@@ramizday3741 Pattex - No More Nails ile yapistirdim, ne su aldi ne buhar yapti. Yapistirici siyah, beyaz ve de seffaf olanu var. Seffaf olani alirsan belli bile olmuyor.

[@YasinHarmann]

@@ramizday3741 Ki zaten sinyal calismiyordu, kendim denemesem veya yanlis kirilsaydi yine de yenisini alacaktim. Denedim oldu.

[@ramizday3741]

@@YasinHarmann teşekkür ederim

[@adark2879]

Hej abi kan du lave min baglygte også samme problem

[@YasinHarmann]

Det kan jeg godt, men jeg tager ikke ansvar for glasset hvis det går i stykker.

[@pedroserrao1306]

Help please where do i find this turn signal led ?

[@YasinHarmann]

Hi, What do you mean by where you find this turn signal led? You mean a new one?

[@SantziBoi]

@@YasinHarmannHi! Also asking where to find replacement led (new one) for the tail light turn signal?

[@YasinHarmann]

@@SantziBoi I soldered old one again. Dont know were to buy new one.

[@adark2879]

Hvor bor du i landet og kan jeg kontakte dig via andre medier for hjælp med min baglygte hehe?

[@YasinHarmann]

Helsingør Nordsjælland, find mig på Facebook

[@Tedkelvin]

English please

[@YasinHarmann]

What would you like to know?

[@jrworpjrworp7254]

@@YasinHarmann how do you geht the Glass off?

[@YasinHarmann]

@@jrworpjrworp7254 You have to slowly break it up where it is melted together.

[@kaurmatthi]

@@YasinHarmann Did you use any heat also, or just carefully prying?

[@YasinHarmann]

@@kaurmatthi No heat, just prying. Theres nothing to soften with heat. The plastic and the glass is melted together.

[@ronniestevens1265]

pr໐๓໐Ş๓