Replaced crank sensor for an intermittent P0335 code on a 2001 Mercedes-Benz E320
Пікірлер: 67
@bismarckgarcia26162 жыл бұрын
Thank you very much for your info. I wish would have seen it earlier. The fact that no light on the dash or no code on the scanner makes it horrible to diagnose the problem. I have been dealing with this problem on my daughters 2000 MB E320 for weeks. Changed fuel pump, filter and relay. worked fine for 2 days and 3rd stopped in the middle of the road.
@roybraswell28414 жыл бұрын
My Mercedes E320 would crank over but wouldn't start. We replaced the fuel pump still wouldn't crank. Me and my Grandson watched this video we replaced the crank shaft sensor and it started up. It wasn't showing up no codes that is why we changed the fuel pump 54.00 sensor and a fuel filter and it STARTED up and the car is still running fine. Thank you for your help Roy Braswell Eastman Georgia
@cameron8783 жыл бұрын
Great video. I didn’t have an inverted Torx at home, a 1/4” 6 point did the job!
@gbush16204 жыл бұрын
Thanks, I hava W210 too and engine won't start with crank sound and check engine light. I start diagnosis by checking fuel cap then replacing all spark plugs. The engine looks normal and engine light gone. Today, I start running the vehicle and run for sometime, stop for a few minutes, then restart the engine. It comes again, crank .... can start the engine, but check engine light. I check the battery by Foxwell tester which ask me for replacing battery, CCA 290/900 only. I do this next week, if fail again, I ponder replacing this crank sensor.
@nancylnichols7 ай бұрын
Thanks so much, as a widow & no males around, my daughter is going to try to help me to replace it. Wish us luck, your instructions seem easy to follow.
@stevenrobinson3464 жыл бұрын
Replace both ("CAM and CRANK") !!! RUNS AND STARTS GREAT NO SHAKEING ENGINE , BACK FIRING , NO STALLING ! NO STRUGGLES STARTING OFF RUNNING LIKE NEW QUITE !!!
@BenzJaguar3 жыл бұрын
Great Video - Can't get the E8 to stay on the screw - Looks like someone tried taking it out and Stripped The Screw !
@ramsanvarghese75677 жыл бұрын
What a great video, thanks for making it!
@jaimecueva121 Жыл бұрын
Thank you Mike for the video. Does my 1998 E320 have the same crankshaft position sensor? In the same drivers side?
@hectorboyar43212 ай бұрын
take a peek.
@stefanrolf2173 жыл бұрын
Thank you very much for this video. Very helpful and highly appreciated.
@mshieh703 ай бұрын
There is no space on w202 c43
@geoffreyjenkins49053 жыл бұрын
great video my Good man,very helpful!!!!
@patioche3 жыл бұрын
Thank you so much for this video. my E320 stalled while driving last weekend.... was not started ... then waited ... then started again .... code P0335. Now I know where it is. Suscribed.
@hectorboyar43212 ай бұрын
That's because the crankshaft sensor is starting to fail. Once it warms up it'll shut off the car.
@SapphyAlexander28 күн бұрын
Help Plz😢😢😢
@FifiRX6 жыл бұрын
it was very helpful, thanks :)
@abdunuri836 Жыл бұрын
my car had a rough idle and turn off by itself i changed the fule pump it was raelly dirty i cleaned the injectors after that i run it , and a poping sound came out of the intake manifold and it never started after that it cranks but doesn't start No RPM while cranking the sparks work fine the fuel reaches the injector could it be a bad crank position sensor? or an intake manifold problem?
@ChadillacTV4 жыл бұрын
Need to replace a Crank Shaft Position Sensor For 1995 Mercedes Benz Wagon E-Class 320. Has anyone here done this for a 95? Is it as easy as shows here? Thanx!
@kendidion31416 жыл бұрын
Roughly how long did it take to replace the CPS? Looks like this job is in my very near future.
@mikesgarage15186 жыл бұрын
It took around 15 min to replace.
@kendidion31416 жыл бұрын
Thanks!
@kendidion31416 жыл бұрын
Took a little longer than 15 minutes only because the E8 bolt was a PITA to get to. Start to finish, busted knuckles and all, maybe an hour. Thanks for the video!
@ManzanitaRecords3 жыл бұрын
@@kendidion3141 I can’t get a socket on the e8. Any advice?
@Theundisputedtruth2 жыл бұрын
Mines is doing the same and then starts back up after a while , u would say this or fuel pump or both
@mikesgarage15182 жыл бұрын
Could be either I suppose. Any crank sensor codes? Have you checked fuel pressure while it is acting up?
@alfredocalpito94393 жыл бұрын
I have the same engine on my 2005, but the problem I have is the car runs but sometimes it jerks on a 60Mph to 70...but at 40mph it’s ok....
@mikesgarage15183 жыл бұрын
any codes for direction? could be engine, transmission or maybe a wheel speed sensor (not sure on that last one). good luck with the issue
@hungphan99245 жыл бұрын
Thank Mike, I follow your instruction to fix my car to day , it not easy but I made it thank.
@matteozig2 жыл бұрын
Do you need to disconnect the battery to replace this? Sorry if you mentioned it in the video. I didn't hear you say anything about it.
@mikesgarage15182 жыл бұрын
since the key was off and no power going to the sensor I did not feel it was needed
@achilleoscostanti96542 жыл бұрын
Hi great video, was the car running lumpy before you changed the sensor ?
@mikesgarage15182 жыл бұрын
It was running ok just an intermittent code set. Code did not return after replacing.
@albertoromano78533 жыл бұрын
Buongiorno, complimenti bel video.
@simonmoreno47576 жыл бұрын
Thanks for the great video Mike! By any chance do you used to work for the dealership to have that software? What's is called?
@mikesgarage15186 жыл бұрын
Hi thanks. No I only do this as a hobby and never worked at a dealership. The scan tool I used in this video is the Autel MaxiSys.
@simonmoreno47576 жыл бұрын
@@mikesgarage1518 did you buy the roughly $300 scan tool? I really would invest in buying one to have that 16 pin diagnosis.
@mikesgarage15186 жыл бұрын
Unfortunately not, the one I bought was just over $2k.
@simonmoreno47576 жыл бұрын
@@mikesgarage1518 your a wild man haha but the good thing about that 2K equipment is you can program or make copies of key fobs lasers right? How's the Mercedes you posted running?
@mikesgarage15186 жыл бұрын
Still running great
@chchcheatas91653 жыл бұрын
Did you unplug your battery before working on the car?
@mikesgarage15183 жыл бұрын
No, with the key off power is not being sent to the sensor
@dongkapuyawn51074 жыл бұрын
Anyway can this remove from under the vehicle? I need to change mine as well. Thanks
@mikesgarage15184 жыл бұрын
Don't think you can reach it from underneath but I did't try. It was pretty easy to get to from the top though
@dogukan43535 жыл бұрын
yeeeehuu its working
@dretovenmusik3784 жыл бұрын
Great 🗣🗣
@zamenfarhan3683 жыл бұрын
Hi there, great video! Thanks. I have the same confusing symptoms with a 2002 w210. Intermittent and mostly start when the car cools down. But it would never die or sputter when driving. It wouldn't start and keeps cranking and I leave it for a few minutes and it starts, it starts right up when it is cold. Would the scanner tell me of it is a crank shift senser or if it is a full pump? Thanks
@mikesgarage15183 жыл бұрын
Hi it’s very possible to have a crank sensor code if it is failing. I had a similar issue years ago and at that time it was the fuel pump failing. Very easy to change on the W210
@zamenfarhan3683 жыл бұрын
@@mikesgarage1518 you are awesome! Your help for all people out here is greatly appreciated. I am taking it to my friends shop tomorrow.... I am having a feeling it is the crank shaft senser position, but will see first if it gives that code, thanks a whole bunch again!
@Kassiusday2 жыл бұрын
@@mikesgarage1518 hi Mike do you think I could drive the car to my local garage around 11 miles away I could go very early in the morning to avoid traffic is about half an hour ? Without risking to stop middle of the road suddenly clk 320 cabriolet never drove it that much only 50K …
@majadsultan51965 жыл бұрын
Thanks
@ابراهيممحمد-ه5م8ي6 жыл бұрын
Dose this sensor effects on car idling?
@mikesgarage15186 жыл бұрын
I would think it could. Any codes stored for the sensor? If you have access to a scope, you could look at the signal to confirm.
@jockw696 жыл бұрын
Is this a CDI?
@mikesgarage15186 жыл бұрын
Hi it is a gas engine.
@jockw696 жыл бұрын
@@mikesgarage1518 thanks. My 2001 W210 E320 CDI cuts out when driving but starts back up straight away? No codes come up either. Very strange!
@owiilezane72223 жыл бұрын
Thank you for the video .. much appreciated!
@Getgoodshawty8 ай бұрын
Hey Mike question , I have 00’ e320 I was driving it perfectly fine then tried to turn it on. Key goes in and all lights turn but won’t start , I guess the crank no start issue but if I try to force the start fast it turns on but dies immediately , any thoughts ? Or will it be the sensor like you said
@mikesgarage15188 ай бұрын
Are you able to see any crank sensor codes? Could be something else, maybe check fuel pressure? If fuel pressure is ok, might be worth swapping the sensor to rule it out.
@Getgoodshawty8 ай бұрын
@@mikesgarage1518 okay will do & keep you updated thank you