MERCEDES W211 FUEL PUMP REMOVAL AND REPLACEMENT E200 E230 E240 E280 E320 E350 E500 E550 E55 E63

[@AutoRepairGuys]

Products that we use and recommend: ► Fuel Pump 1: amzn.to/48bf2ur ► Fuel Pump 2: amzn.to/483TvUB ► Panel Removal Set: amzn.to/3YiMADu ►Torx Set: amzn.to/2hbyWgd ► Tool Set: amzn.to/3p5MM6t ► Screwdriver Set: amzn.to/3XRB28Q ► Engine Oil: amzn.to/3xBc8B9 ► Oil Filter: amzn.to/3w0Ulme ► Torque Wrench: amzn.to/32qyRwg ► Liqui Moly Engine Flush: amzn.to/3IiDBID ► OBD Scanner that we use most often: amzn.to/3I4MQfe ► Check out our Amazon Store for the tools and parts that we use: www.amazon.com/shop/worldmechanics

[@markjones8632]

Imagine 700 dollars for a 30-minute job! This video does a great service to those who have to earn their keep. Thank you.

[@botribe]

This video was completely helpful. I changed out my fuel pump and and fuel assembly. 4 1/2 hours Not too bad. Actually. This video was very informative and helpful

[@josemartinaguirrerubio9273]

Thank you for explaining on this video is a lot more better compared to all the other individuals that do not explain what really needs to be done.

[@Nyck461]

Video has good information. Two things I would do different: 1- Clean the area around the covers with a good vacuum. I noticed that there are a lot of dirt going to fall inside the tank. 2- Before removing the right side fuel pump, I would pass a string crossing inside the tank to be easy pulling back the cables to the left side. Other than that, video is OK.

[@papagigo1]

Good idea !

[@Jiusonium]

What a great idea, thank you!

[@jagvette1]

OK Guys firstly let me say thank you for doing this video, I am a mechanic with over 30 years experience but never to old to learn and also I do not know everything, my wife has a E350 and these videos are helpful, one thing you did not show or mention and that is the re-install of the filter and what a pain in the ass it is to feed the pipes and cables across from one side to the other and also where the hole is that these have to be fed through, I'll leave it to you to explain to your viewers.

[@zachmassey2462]

When you take the hoses out you should tie some rope to the end as you are removing it and then the rope would be hanging out both holes. When you are reinstalling the hoses attach the hose to the rope and pull the rope so the hoses line back up.

[@jagvette1]

Yes I thought about it afterwards , you know closing the stable door after the horse has bolted :)

[@honchoryanc]

if you are going in there replace both units

[@johnohill463]

Auto Repair Guys You should depressurise the fuel line before you disconnect the battery. INSTRUCTIONS1) - Remove the fuel pump relay.2) - turn the engine over for 5 seconds X2 - The fuel line in now depressurised. 3) - Put the fuel pump relay back in.4) - Disconnect the negative battery terminal. 5) - Commence work on replacing the fuel pump and fuel filter.....Johno's Mechanical Engineering.

[@BrianBaccus]

you should a video doing it, this way we can see how its done

[@aaronnkondo2591]

This Is good work guys. Really learning alot. That area looks very sensitive though for an amateur like me to handle.

[@MiamiMostSwaggest]

How do I know it’s just the filter and not the pump? Thank you for the greatest Mercedes videos! We love it!

[@douglundy5755]

right side is pump, left side is filter. both have floats

[@VeryImportantFish]

I am so grateful for your video!! I did have a full tank of gas and I didn't realize that the fuel would gush out. Other than that, everything went smoothly.

[@lukerobertswr5189]

was it hard to get the hoses back to the other side?

[@VeryImportantFish]

@@lukerobertswr5189 I barely remember doing this but as I recall, I didn't have to go that far. I only had to work on the one side.

[@RoadHeros610]

I have a big questio in your opinion you dobalot of vids on odb scanners which do you think is best in the 5 hundred dollar bracket that can do all actuation test on. Mercedes and code modules ... I'm ready to by the best for money

[@ulaskelav4042]

You guys are amazing !!! helped me to save $1,100 ! Everytime I watch your videos before I fix something ! But I’d like to add something in here it could help maybe to others. Small plug which is Electric plugs on the filter/transfer ( driver side ) have 2 different type of head I don’t know specificly but I had that situation fyi !

[@samishukir604]

Greetings from North Africa I am following you

[@bpabba]

Hi guys - you folks are amazing. Ever since I got my E320. W211, I always first see your videos before I do anything on the car. Thanks for all you helpful videos. I recently got a check engine light - and I had NAPA look up the code and its is a P0101. So i researched it and found that it was the MAS Air flow sensor that was part of the problem. So I removed and checked and the rubber gasket and surrounding body of the sensor was damaged and replaced it along with new air filters. Vehicle runs fine - but not able to clear code. Any advise ? Id greatly appreciate it.

[@jeremybakke2868]

My 2007 Mercedes Benz e350 base dose not have any thing on the passenger side of the car at all . Just got the fuel filter on the back driver side with the fuel pump next to it on the other side of a little metal wall. How ya get that out never seen that be for .

[@reys_live7243]

Does a 2004 mercedez clk 500 have the same fuel filter location ?? Does it have a external fuel filter location out side of car ??

[@michaeljenkins3060]

Have any advice as to why I replace both and it gets power but the pump does not get power

[@exup92]

You guys are great. I have done so many repairs on my S211 following you.

[@TipODissPrimeTheGreat]

What can be done if the pippit the hoses connect to breaks inside of the plastic hose?

[@Yawanathan-144]

Can you put the link for the fuel pump you purchased for the e320?

[@douglundy5755]

so when did you unhook the hoses from the other side with filter? they dont just come out!

[@OneamorFati]

Love the video, thank you. So EYE was wondering if you guys can tell me the exact name of those two parts. EYE have a 2003 e 320

[@eraldberdo9537]

Great video guys with a lot of tips!! I got an issue with my E class 220cdi 2011. Engine turns off to quarter of level fuel, and when I fill the tank again needel goes up just fine and goes down while you consume it. In this case which may be the problem the Level sender or the Fuel pump?

[@Cetax]

I am goin thru the comments and spoted yours. I have the same issue and its 99.9% the sender, havent replaced mine yet, tbh cant find that unit to buy.

[@eraldberdo9537]

Hello buddy, after quite a while did you fix your Mercedes? My one I didn't yet, quick question I should replace a fuel sender unit or the fuel pump? Take care

[@brnstubby7]

Good day, Thank you for the video. Please kindly tell me what is the name of that fuel filter with power cables connected to it?

[@dennisdunkley2570]

Can you recommend anyone who works on MB? I live in Union County NJ

[@-stayblessed-8866]

Great video!! if fuel sending unit doesn’t work the car won’t start, correct?!

[@benswann5374]

Suggest VACUUM that crap out before disconnecting/opening. I do that and follow with compressed air - nice and clean. A little good cleaner/light oil and wipe. I swear by Gibbs - lube, clean, surface protect, does not mess with paint and can paint over.

[@lobsterjeans5815]

Should you do this on a empty tank?

[@jagvette1]

no you can do it with fuel in the tank but obviously careful with ignition sources and leave widows open or it will stink out the car

[@javiermoreno5593]

Does anyone no were I can't buy the fuel pump for left and right side I went to autozone and orielys and there pumps didn't fit my car some one please help

[@Dnasty1]

Is it safer to do this with a close to full tank of gas to reduce vapors? I see a lot of people do this on an almost empty tank but I would think that is more unsafe.

[@boomerbutler6358]

Hey guys thks for all you do but ? I put 5 gallons of gas in the car and didnt realize it had water in the gas what do I need to do what is your suggestion thanks

[@josemariacastanedaperez8526]

Good afternoon, I'm from Matamoros, Tamaulipas, Mexico, I have a Mercedes E280 and unfortunately my gasoline pump stopped working, I managed to locate the part I need from a Mercedes E350, my question here is if the E350 gasoline pump is compatible with The E280, I asked and they said yes, but I would like the opinion of experts, thank you and excellent video.

[@papagigo1]

What side has the float for the fuel gauge on the dash ???

[@JoseHernandez-gl9rm]

we're can I find this exact fuel pump assembly?

[@houstontylerjames8812]

Can you do a 2005 clk320 fuel filter ?

[@YadiBarbie]

Hi, I watch you guys often. Please help is there anyway to go around a sealed fuel tank? Mercedes found a fault on my electric fuel pump and stated I need a fuel tank replacement for 4k Help Me

[@mb.warehouse_find4221]

PZEV ...do you have any recommendations if your Mbenz W211 E350 is a California low emission "PZEV" fuel pump? My fuel pump stopped working and dealer said that the whole tank needs to be replace!?!.... first time I've heard of that stupidity design? Mine does have once access which is on the driver side but they said that is the fuel sender? and the actual fuel pump is inside the tank. No wonder the passenger side access when you unscrew the 8mm bolts there is just metal - no openings to access whatever is inside it,,,, tell me there is hack to access the fuel pump pls.... or else the dealer is charging me $4k to replace the tank (parts & labor). Sincerely

[@ryonesamer8112]

Is it same for w211 e220 CDI 2007 ???

[@hossamfawzy7631]

Thank you so much

[@rodzrivera9019]

Hi where I can find tha fuel pump with tha pressure sensor

[@osamabshna3331]

Is there a difference between the power of the fuel pump E500 And 320

[@traycool4604]

Saved me 100s of dollars.. Bought a Crankshaft sensor thinking it was that, then replaced all fuses and relay.. Fuel pump was my last resort.. found out the fuel sending module stopped sending fuel back to pump.. gave it a little nudge.. tighten all hoses.. then VOILA... thanks!!!

[@ruhsatigoek1632]

Super Video

[@Stateproperty30]

Very useful video! Had the pump exposed and tested in 5 mins after watching this! On to the injector pump :(

[@-stayblessed-8866]

How did u test it to confirm the lump was workin ?

[@gustavomendez1321]

How do you get to the fuel filter

[@CaritsJeremy]

Thank you. this is so helpful

[@reneegunther5837]

A friend suggested YOU would be the one who would know the answer. I so hope you do! I have a 2007 CLK 350 Cabriolet. Service members needed to gain access to my fuel tank three times. The next time I turned the car on, a warning message on my speedometer read: "SRS Restraint system malfunction drive to workshop." It was diagnosed that the driver's side airbag needed to be replaced. Could moving the front seat all the way up cause this? Could it just be a coincidence? Here's the kicker: There has not been one available in the U.S. or Germany, and it has been back-ordered for months. Could it just be a coincidence?

[@anestorabi7890]

Thanks for vidéo

[@TTGPATCHER]

My cap to hard to come off any ideas you have ?

[@muhammadkhan-xo8iv]

How to know mercadez timing chain need chsnge And fain belth or AC belth procedure of replacement

[@jubrilajala1974]

Hey Guys! Can you help me out with a video or Detail Diagram of where the P0451 pressure sensor switch is located on 2007 GL450? Thanks

[@edgardelgado8994]

Can i replace just the fuel pump without replacing the driver side?

[@funtodovr5501]

Make sure you clean all the dust before removing fuel pump and/or sending unit.

[@henrylong45]

Dude. This looks DANGEROUS!

[@elephantemane]

Bonjour ou se trouve la pompe à essence sur Mercedes classe A 150 classic w 169 Merci

[@abrahamsaldivar9434]

how can find fuel tank sensor 2001 c320 mercedes

[@justhim8745]

Can you make a video replacing fuel injectors

[@erics8514]

Thanks

[@adrianflores9026]

Good job thanks

[@electricfuzz3425]

I replace my sending unit behind driver side And it still no power to my fuel pump or sending unit I haven’t checked it with a multimeter but there’s no noise or fuel + crank no start and it is brand new any suggestions?

[@timothyhector9424]

Did u find the problem.can u give me a call at 2516480719...tim

[@reneerogers9680]

The MAIN fuel pump in the passenger side!! Discovered that the HARD way. The driver's side is called a sump pump/fuel filter assembly!

[@reinhardtrippmacher8776]

@@reneerogers9680 when you talk about driver and passenger side. we got a RHS steered MB. What side is driver side for you?

[@reneerogers9680]

Sitting in the vehicle...fuel pump is right side....so behind you as driver on RHS😊

[@ertanbargu5679]

I would like to thank you for your gratitude. mercedes w211 2008 model ceiling drop how to repair the detachable gondola

[@ernest8175]

Nice video ! what's the fuel filter part number guys ?

[@michaeljamesm]

Febi 39831 fuel filter

[@adriannyasia]

Is it possible...?

[@thesally125]

Did you know there’s a special tool to remove the black housing? It makes it move much easier and the housing doesn’t get any flat head marks!

[@KandiMan]

That ridged cover ("ring nut") is $5, not a big deal to let it get marks on it. The tool you're talking about is $60.

[@johnlenerd]

OPEN the gas cap to release preasure first.

[@newmanzakaryan6430]

Thank You

[@newmanzakaryan6430]

good job , here in KZbin some never get happy dont listen them

[@ridemydirt2005]

where is the reinstall video?

[@smartbeatz42o]

The hardest part is reinstalling the plastic that holds the pump yet they provided nothing on how to do it

[@YXEFlatl1ne]

@@smartbeatz42o how do you do it???

[@gmakutube]

Guys: Your website does not have information about the fuel filter. Is this just click bait to get eyeballs on your web-site?

[@miked7162]

You can't find a filter ? 😂

[@ChowOne]

I LOVE how he says always make sure to wear gloves and eye protection. Yet he isn't wearing either. Smh

[@benlogann]

where is the fuel pump located on a 2007 mercedes e350

[@lilmoco8305]

Back seats bro

[@electricfuzz3425]

Ben Logan same place under seat it’s a release on each side of back seat at bottom corners

[@papagigo1]

Mercedes doesn't make it easy

[@worldofvideos8198]

where is mine on the c230 Kompressor Sports 2004 model

[@jammellbrown1663]

How many fuel pumps does the car have 1. Or 2

[@jesusonewilmas]

Jammell Brown according to this video one the one on the passenger side

[@hella_2350]

Jammell Brown. 2, one is the auxiliary pump (when one side of the tank reads low, it uses the auxiliary side to feed it more gas) fuel tank is designed weird. At least this one can be replaced individually, newer cars use a similar design but can only be replaced altogether. Expensive as hell too.

[@Quelm1]

Gelacio Tiburcio Wrong! It has one pump. It’s on the right side (passenger side). The other side (driver side) is a fuel filter. People often confuse it with a pump cause it also has a level float. Driveshaft divides the tank on the lower half. Because of this the filter housing also supplies fuel to the pump side as well through one of the hoses. Basically it’s a single pump system with two pickups and two lvl floats and also a strainer on the bottom of the pump.

[@Jiusonium]

It has one pump, but it's a part of an assembly. The other part is the sending unit which has the fuel filter.

[@ahmedalmoaidali1835]

Thanks vvvery much

[@hamzaerraji9824]

Same thing for clk500 w209 06-2002

[@playharder1435]

Rings are dangerous conductors in this line of work... A mechanic melted one of his fingers OFF around a battery --- all because of a wedding ring 💍

[@danielc1886]

July 24, 2023 --- Hi. I own a 2008 Mercedes E350 V6. The fuel pump is no good. I went to my mechanic and he said that the pump cannot be replaced by itself. I have to buy the pump and the tank. That increases the price of the job. The parts alone are $2500. But I and my brother-in-law watched your video above. It seems like you are working on an E-350 but you are able to replace the fuel pump with another fuel pump. You are not dealing with the tank. Why is the Mercedes dealer and my mechanic telling me I have to buy the tank and the pump. Thank you for your help

[@DimlyAwareHUmAn]

What the heck? You tear the whole damn thing apart, and then don't put it back together? Had to scour through your many videos only to find no installation video. What was it like fishing those hoses back through?

[@commonsenceaintsocommonnom1496]

Lhh he probably fucked it up smdh he'd definitely had 1 showing the success

[@KIYOOU]

От къде сте момчета?

[@MikayilAbdullayev]

Hitting a metal screw driver with hammer is extremely dangerous because even though the ring you're trying to unscrew is plastic, there is lots of metal around it and you can accidentally cause a spark.

[@dannieoh8112]

So how do you unscrew it?

[@shifty2755]

On a petrol yes. But not a diesel. But They should be using the correct tool.

[@shifty2755]

@@dannieoh8112 Use the correct tool.

[@Jiusonium]

​@@dannieoh8112I usually use a piece of wood instead of the screwdriver

[@jimmydigiannatale3131]

I have 2002 mercedes Benz c240 crank no start

[@abrahamsaldivar9434]

fuel tank presure sensor c320 2001

[@MultiRedactor]

Зачем хомут порезали? Он снимается и потом ставится на место.

[@DonnyBerger]

Dank u, com agan

[@3030hp]

who the hell came up w/ this design LOL

[@DavidTheMechanic]

You thought that it was the fuel pump 😅😅

[@CopybutNotPaste]

what is the world is the guy wearing on his hands. lol, thanks for the video

[@zamiryi]

Voice, painted pinky and ?Jersey shore watch, GTL FTW !!!

[@t.cod-addicts708]

AFCOURSE i have the 270 which is without fuel pump ! and sucks gasoline by an underpressure system

[@DavidTheMechanic]

Ooooppppssss wrong side😅😅

[@Saltu61]

Ever order any parts online unless you more than one because when the part fails you screwed for a week or 2 I learned my lesson the hard way after been an online parts customer for a long time but after getting a high quality brand name parts that failed in less than a month I never again and never again and never again fk all them online sellers

[@vietmanesemechanic6331]

u supposed to open R side only

[@gregorygereben830]

you need to do a little research before you take things apart

[@rollingwithdjrayhan]

3:22 this dude nearly cut the hose with that pliers,,

[@adriannyasia]

Dude, clean that pump area first. I cringed the whole time.

[@vietmanesemechanic6331]

no tool to remove cap

[@jasonhitch660]

Absolutely horrible video. I expect better from you guys.

[@Milano_milano]

Ich bin nicht so schlimm ich bin nicht mehr so lange her aber ich hab dich voll vermisst und du redest du nicht so viel ich bin ja nicht das ich so viel Geld habe ich hab dich auch nicht so viel zu tun und was macht dein Herz und was ich dir das so jdididd du hast du dich so gut wie nie gesehen du siehst so schön und was du willst kannst mich gerne mit dem Hund haben aber das ist ja nicht so viel ich will nicht was du willst ich mach dir

[@clydedavis5634]

Should have shown how to reinstall everything you took out! 👎

[@marcojuarez5413]

Coke pinky

[@Milano_milano]

Bdidbdd