Mercruiser Tilt Trim Not Working Dirty Switch Fixed & Tested, BayLiner Capri, FnF420,

FnF420210330, Boat 072, Mercruiser Tilt Trim Not Working Dirty Switch Fixed & Tested, BayLiner Capri

[@oscarpuentesvargas650]

Put my boat away for the winter season. Everything worked fine when trimming up and down before storage. I went to start it today after it’s long winter nap. Now it won’t trim up but will down. I will be trying this tomorrow !! Thank you

[@jamiehackney4420]

I have the same issue. Worked fine when I put boat up. Did this work for you?

[@gr55721]

Update please. Did it work

[@shawti77]

worked for me in June 2022! Thanks for sharing, I cleaned the contacts with muriatic acid and sand paper and then applied some waterproof grease to the o-rings. Only my trailer and trim down were working previously and now the trim up works perfect. Awesome video!

[@friendnfamily9053]

Thank you for sharing!

[@cme4brain11]

This was a fantastic helpful video. That shows me how to fix my trim sensors. Couldn’t of done it without your help.

[@friendnfamily9053]

👍

[@dynamitedmoney]

Thank you so much for making this! you just saved me a ton of work I thought I had to replace the entire switch and worked for me! Thank you thank you thank you!

[@friendnfamily9053]

Thanks for your sharing and for your nice comments! Glad it helps!

[@mikedonaldson6247]

I used a small wire brush to clean up,thanks to this video it was my fix,thanks much

[@friendnfamily9053]

Thanks for sharing!

[@mikedonaldson6247]

The very problem I had .thanks to this video trim is working as it should,thanks much

[@friendnfamily9053]

Glad it helps!

[@hugolafontaine5195]

Thanks so much for sharing! Fixed my problem!! 😊

[@StevenSambuco]

Dude! Something so damn simple and it worked for me as well. Awesome! Thanks my man.

[@friendnfamily9053]

Glad it helps

[@seeya4046]

So we are supposed to guess what liquid you’re using there???

[@mvanderw379]

Thank you, had some problem. Outdrive stayed up, pump worked but drive didn't go down. Same noise as when it reaches bottom. After trying couple of times while steering and driving it finally went. I guess I need to add some fluid. Also wasnt sure if it limited on the downside, it doesn't. Now I m reassured 😉

[@georgepierce9825]

Awesome tip!!! I did exactly what you described and it works!!!! Thank you!!!!

[@friendnfamily9053]

Glad it helps and thank you for sharing!

[@olfarmboy405]

Thank you for this video! This fixed my issue.

[@friendnfamily9053]

Thank you for sharing!

[@MarkLamontia]

Great suggestion. It worked. Thanks!!!!!!!!!!!!!!!!! :)

[@nicholasm2239]

this is interesting... looks to me from the design of this switch its meant to be able to trim up a lot further than you have it set to. There is plenty more range of the contacts to allow for this and also prevent the hydraulic panic at the bottom which you might not hear/feel in the water. Isn't that what the top and bottom bolts are for? (to adjust the range of where the center (rotating) contact is falling off the stationary ones?) or i guess just rotate the main cylinder a bit clockwise before reinserting it? i guess what i'm asking is what is the benefit of limiting your trim up this aggressively?

[@robertdillahayii4763]

So you don't trim the drive into your hull

[@jaymorgan8017]

Your kid has more patience than you deserve. Or so it seems.

[@toddcornelius5817]

Awesome THANK you

[@DwightWillmon]

What cleaner are you using?

[@ghumphrey85]

I think I need to do this. Mine goes down, but when going up you can hear a relay click but nothing happens. If you start the boat it will then work. I’m thinking the vibrations help the contact.

[@bigreesenrndav9161]

Hello. Is there a video on adding grease/fluid to the trim?

[@tonylopez9373]

You should said I’m going to put this kind of liquid here we can’t guess what did you used

[@drewunderwood2859]

Thanks, I figured there had to be a limit switch, start with the simple stuff first. Person I bought the boat from said it worked one min then quit ( luckily in up position).

[@friendnfamily9053]

Thanks for sharing!

[@davinbreeze6987]

Is there an adjustment on there with the two outside screws ?

[@mrmorksstuff]

worked a treat ! Thanks :-)

[@friendnfamily9053]

Glad it help!

[@brendaespinoza1851]

What did you clean it with was it gasoline

[@dumpsterfire6351]

Ayyyyeeee thanks

[@carlosflores4104]

Good 👍🏼 video

[@TACEKLOGISTICS]

What chemical did you use to clean the switch with?

[@TACEKLOGISTICS]

What chemical did you use to clean the switch

[@mchaves7663]

Thanks for the video. How long did acid take to remove the corrosion?

[@friendnfamily9053]

Hi, thank you for watching! It took less than 3 minutes. Hope that helps!

[@reymurguia9798]

Thanks

[@leesire]

Thanks for sharing

[@friendnfamily9053]

Thanks!

[@thomaspaccione7214]

What did you use to clean the corrosion?

[@friendnfamily9053]

Hi, It’s muriatic acid. Please review its SDS & stay safe! Hope that helps!

[@DjStalin100]

Do they just sell the circle gaskets? What brand of grease? Thanks

[@friendnfamily9053]

I was using accessed grease that was already in the part. Not sure about the brand.

[@macarioaguilar6784]

My trim works but my trailer switch doesn't? what could that be?

[@raulfernandez9111]

Trim works up and down but trailer button does not? Have you checked the fuses at the trim pump? I believe there are two fuses.

[@ericeklund7169]

Hello. My trim down works and the trailer button works on my 2001 bayliner. Any idea why the trim up won’t work? Could it be the switch like you showed here?

[@friendnfamily9053]

Hi, it could be.

[@jordanteegarden7065]

Yes could you let’s us know what you used?

[@friendnfamily9053]

Hi, It’s muriatic acid. Please review its SDS & stay safe! Hope that helps!

[@gimamotor]

Pretty new drive to have this problem

[@Kayzhavez]

what was the liquid you used to clean it up please?

[@friendnfamily9053]

Hi, it was diluted muriatic acid.

[@Kayzhavez]

Thank you