This video is a collection of maintenance items which includes the replacement of Fuel filters, engine thermostat, removal of a frozen bolt and anodes for this 2015 mercury 60hp EFI engine. Enjoy!
Пікірлер: 27
@timc89137 ай бұрын
Appreciate you sharing. I replaced the plugs on my 60 hp and couldn’t find a feeler gauge so I just put the new plugs in assuming the gaps would be close. Judging by your plugs I need to take mine back out and gap them properly. New subscriber. 😊
@tedsmarinerepair89567 ай бұрын
Good idea, standard spark plugs should always be checked prior to install. Just not platinum or iridium
@ronhousmancpyb34457 ай бұрын
Nice job- especially like your tips and tricks!
@michaelmilton44273 ай бұрын
Great video thanks, if I may ask a question about my mercury. I have a 2003 mercury efi 50hp outboard. I just bought it and don't know the history, I noticed oil coming out of the water inlet. Any idea what it might be? Also do you have a video addressing this? Thanks Mike
@waynewolfe88179 ай бұрын
I just purchased a 1996 monark bass boat with a 9.9hp two stroke. I watched your video on "no spark" on a 15hp and believe the switch box is the issue. Question, does the 96, 9.9 have annodes?
@tedsmarinerepair89569 ай бұрын
Yes under the cavitation plate part # 42121A2
@waynewolfe88179 ай бұрын
@@tedsmarinerepair8956 thank you!
@waynewolfe88179 ай бұрын
@@tedsmarinerepair8956 I already have a new one ordered. I haven't had it in the water yet, but I doubt it 50 hrs on it, but it's been sitting for about 20 years ...
@thomasserovich95646 ай бұрын
First off, great video. I really appreciate you taking the time to post. On your iPad, what book or app or program were you looking at that illustrates the parts break down? Where can I find this? Thank you sir.
does a 2021 mercury 60 hp 4 stroke have a poppet valve?
@waynewolfe88179 ай бұрын
Can you use "de-ox" on the annode bolts to keep them from corroding? We use it on electrical connections in pannels.
@tedsmarinerepair89569 ай бұрын
I am sure it would work on "dry bolts" with no water nearby, I would not use it underwater or where salt water might come in contact with it being its for electrical terminals.
@waynewolfe88179 ай бұрын
@@tedsmarinerepair8956 ok, got it, it would need to be waterproof.
@tedsmarinerepair89569 ай бұрын
Yes, good idea either a good marine grease or TEF GEL which was designed for marine use@@waynewolfe8817
@Rosco35466 ай бұрын
I’ve got a 2008 mercury 60 4 stroke I put new spark plugs in mine e but didn’t use a torque wrench I did 1/2 a turn after finger tightening spark plug is that ok ?
@tedsmarinerepair89566 ай бұрын
Not the recommended method. The reason spark plug torque is so important is 1) The threads are not damaged due to overtightening 2) If the torque is low, the heat transfer from the spark plug to the cylinder head may be insufficient which can lead to spark plug pre-ignition.
@muc414910 ай бұрын
3:52 that's some great advice!
@michaelschnepel50003 ай бұрын
The reason that bolt won't come out I'll bet is because it hasn't been greased ,I always grease the bolts and gasket on mine because I check and clean it every 6 months, thanks for sharing going to check spark plug gapes
@adhdgaming23773 ай бұрын
Ive got the most odd problem with this engine where im having issues with bogging and it running weird .. ive. Did a full service new spark plugs low pressure fuel pump high pressure pump regulator cleaned out vst new fuel line new filters water pump everything... The only thing i can think it might be is the IAC valve becuase ive seen other simular problems with similar synptoms.. but nothing has worked yet
@tedsmarinerepair89563 ай бұрын
@adhdgaming2377 the IAC will cause low speed issues not engine logging. If it's surging/bogging I would try running it with a fuel pressure gauge to see if it holds constant fuel pressure in the range it should.
@dreamfly5552 ай бұрын
where did you get the torque specs for bolts?
@tedsmarinerepair89562 ай бұрын
@dreamfly555 I always get a service manual for the torque specs.
@scottburgess21509 ай бұрын
Do you just punch a small hole through the top of the oil filter to drain it