Meshing in ANSYS/Global Mesh Control/Part-1

[@vellakoil_Kattuseval]

Expecting some good videos in future too.. keep rocking

[@graspengineering9249]

Thank you

[@mshafiq109]

Very informative and descriptive.

[@graspengineering9249]

Glad it was helpful!

[@AV-bp3bc]

excellent . keep uploading videos on meshing and other imp tools

[@graspengineering9249]

Thank you for appreciation !

[@vellakoil_Kattuseval]

Excellent ... Thanks for keeping promise

[@graspengineering9249]

Thank you

[@yogeshpakhale8321]

Thank you Sir for sharing this video. Please do share ANSYS meshing Part 3 video link.

[@graspengineering9249]

Ok sure

[@SDMENaveenH]

Super sir indepth explanation

[@graspengineering9249]

Thanks and welcome

[@guide312]

Much Better than paid tutorial.

[@graspengineering9249]

Thank you for appriciation

[@dipakgaikwad3937]

nicely expressed sir..thank u so much..

[@graspengineering9249]

Thank you for appreciation !

[@anengineer8647]

Sir please share part 2 for your more knowledge about meshing... Part 1 is very useful to me

[@graspengineering9249]

Okay ! We will Upload Next week !

[@anengineer8647]

@@graspengineering9249 thank you sir

[@mani4r]

Thank you very much hope you will keep on this in future also...

[@graspengineering9249]

Welcome!

[@noumanashfaq7419]

Thank You so much. you are a life saver

[@graspengineering9249]

Welcome.

[@TuanVu-om9gt]

I'm struggling with simulation of Hertz Contact in Ansys. Cannot match the verification value. Could you please make a tutorial about this topic? Thank you

[@mahenderbari100]

Thank you soooooo much for Ansys 🙏🙏

[@graspengineering9249]

Most welcome 😊

[@0115221341]

first of all..this is impressive sir!! please please keep uploading.. second i need to know how do i know that my mesh is good or bad? is there a parameter should i know from it this thing? and thanks in advance

[@graspengineering9249]

You need to check the quality of the elements. like aspect ration, jacobian, skewness, min & max. angles, etc. All this parameters have specific range, you should limit your element characteristics within that range.

[@0115221341]

@@graspengineering9249 thanks for replying sir! please can you tell me what are the limits of this metrics ! and thanks in advance

[@graspengineering9249]

One More video on Mesh Quality is in Que, will upload near future. You can google for mesh quality limits too.

[@ansysburn8078]

good job

[@graspengineering9249]

Thanks

[@rishabhbiddappa7342]

Which version of ansys is it?

[@graspengineering9249]

Please check complete video, you will able to find out on screen. It is R19 version.

[@rbffr]

It's showing adaptive sizing -yes or no No option for curvature proxi

[@graspengineering9249]

It might be due to ANSYS Version. Try to use Latest ANSYS version for newer setting on mesh controls. We will update this video as per new setting too.

[@kunalgavane6530]

Very informative video. Thanks :)

[@graspengineering9249]

Thank You for appreciation !

[@kunalgavane6530]

@@graspengineering9249 Is your ANSYS a paid version? As I dont have proximity n all options in mesh?

[@graspengineering9249]

It should present with students version. You can do local mesh if proximity is not working. Sometime local mesh without proximity setting gives good mesh with less node count.

[@kunalgavane6530]

@@graspengineering9249 Thank you for the reply :)

[@manojpokhriyal1183]

Hello sir , how can I sort the error saying: the mesh generation did not complete due to poor quality elements or incorrect input. please try meshing with another mesh method or different mesh option. As I have tried different settings but still showing this error . Sir please can you guide me , what to do.. Thanks in advance ..

[@graspengineering9249]

It may varry from geometry to geometry. We do not know your problem statement. But try to give body sizing and method (Tetra, hex) to individual components and try.

[@RAJEEVKUMAR-gn7ce]

Sir can you make a video on bearing analysis

[@graspengineering9249]

Okay, If possible we will make !

[@rogerharsh]

Part model link please

[@emreerdogan4360]

Are you using ANSYS as a licensed software?

[@graspengineering9249]

Hello Emre, as discussed earlier, if you are looking for training on ansys, we will let you know once our coarse is completed. Also if you are looking ofr any ANSYS support you can check our patreon page.

[@anijg05]

Hi, thank you for sharing your knowledge! :) If someone ask me how big is your mesh, do I need to say 18,640 elements or 33,275 (@27:25)?

[@graspengineering9249]

The FEA calculation are performed on nodes, so the number of nodes represent the mesh count. But while showing FEA mesh number, you should show both number of elements and node count.

[@ksatgoud]

Sir, I am from Hyderabad and working professional, your lectures are good, still I want a direct Training, so that doubts can be clarified, where can I get direct classroom training for Ansys for industrial applications or the Best Tutor in India preferably near to me.

[@graspengineering9249]

We have more than 100+ videos on our channel, you can explore each of them and if you have any question put in comment section we will reply ASAP. Also we are working on few courses once completed, will update you. There are so many platform where you will found ANSYS courses but I am not sure about the depth they have covered.

[@JBVerma-lb8lm]

Sir how we wll give velocity profile ( in x ,y and z tables) as velocity input.

[@RobertBaiko]

You don't have to clear the mesh every time you change a mesh setting. You just remesh and it will toss the previous mesh.

[@graspengineering9249]

It is okay for single component. If you have multiple components then it is better to clear the mesh and then do remesh.

[@visheksingh9431]

Thanks for sharing such a informative video! Does it possible you can share the PPT which you used for the explantaion of FEA, Elements & Discrtization?

[@graspengineering9249]

Welcome ! We Only share information through videos.

[@26jasti]

Why do you have a loud background music man :(

[@graspengineering9249]

the back ground music is not considered in the new video's.

[@dr.omprakashsingh4532]

No need to clear the generated mesh. New mesh automatically updates.

[@graspengineering9249]

Yes. But when you have more components in that, you will need to clear the mesh.