Microbeast Plus Pro v4 AttitudeControl Setup

[@adolphjanssen6580]

Thank you Tom I have been struggling to get attitude control to work because I did not tell the beastX that I had a standard receiver. After I whent in the receiver menu and saved the setting OFF (standard receiver) everything worked fine. Gave you a thumbs up

[@wjkssmd]

I was wondering how they control the V4 software. I have a couple of BeastXs around. Thanks for a good setup video, you saved me some time.

[@wjkssmd]

+wjkssmd If you leave the switch in auto-level mode (the first mode you selected), can you just let it set there hovering... just controlling collective for altitude,

[@RC-Heli835]

I like the quickest way to level with a tiny bit of climb best. In some instances there might not be time to flip upright.

[@pauliether.c.guy.3349]

Thanx Tom your the best i struggled setting up the beastx gyro. You see I have a Tgz-380 which is a beastx clone. it has the the same exact functions as the German man beastx even the same little cheat sheet. I struggled with parameter k setting the both positive and negative pitch a 12 degrees in both directions. My problem was my helicopter would spin uncontrollably in circles. I had too much pitch in both directions not realizing it had to be between 11-13 degrees no more than 13 degrees.Oops stupid me. As soon as i set it up like you the spinning stopped with the exception of reversing the gyro. Now my next problem is how do you lock the preferred pitch into your gyro? I know it's done on the stick of your transmitter but how do you do it? do you press left or right up or down it can be frustrating. The only reason why i chose a beastx gyro is because you dont need a computer to set it up which I love unlike many other gyros such as the Align flybarless, Ikon2, Mikado Vbar, Zyx by Tarot. et Can you please help Tom? Thanks.

[@nealjag3917]

thank you so much you help me out a lot if you have an extra Chanel on your receiver how do set it up i need help thank

[@cagefreecleric1834]

really nice video this type ( the plus series) of microbeastx is totally different from previous version , need more especifict set up. thanks

[@7250dk]

Tom, Is there anyway you could make a video showing your settings for the DX9 and the Microbeast?

[@quicknickk]

Hi there. Yes. I have done the same. Replaced my AR7200BX with nitro govenor to BeastxV4. Very expensive paying for it in Rands. (R1817) BUT now, it says using a standard receiver (AR8000) I cannot enable the menu N for the nitro Governor? To be able to use the nitro Governor I need to use a satellite receiver. BUT now, in the manual it says NOT to use just the satellite for anything bigger than a 450 because of its range. So therefore you can only use the governor on a 450? So very disappointing at this stage. Dont know what to do from here for governor. ANY HELP?

[@SiLvErDanCeR100]

I can't find how I can choose how fast and how pitch I want to give.You said it must be at G spot for first fly.Where I can change that?Thank you

[@easty6615]

Hi really informative video...good job. Thinking of getting this for my heli. I'm used to Align Gpro. Where does throttle (ESC) throttle cable plug into?

[@crystalhelix]

I am proud to be your friend.

[@katzmeownet]

HI Tom, Thanks for the video. I am using AR7210BX with Safe Tech. One tip in your video that is a little scary however is that you must do the complete setup of everything before you activate SAFE technology. OK, maybe the first time. But what about if you make a simple change to the setup down the road? Does that mean you have to turn off SAFE and then activate it again? Or do you have to reset the AR7210BX and do the whole heli setup again? Seems to me the thing should be smart enough to grab all the setup information every time you boot it up before you fly.

[@chriswilliams78601]

Hey Tom....Thank you for such a fine tutorial on BeastX V4.. just purchased a blade 360cfx and would like to install V4 with attitude control. HH will not make any mention of Beastx V4. I suspect AR7200 and AR7300 old stock will need to be moved out before they will make the next Offering...... AR7400 with attitude control?

[@lakufoekdm4237]

Sophisticated fbl unit...

[@MrSpike2450]

Thanks for the videos, much appeciated. reading through the latest instructions it seems that the gain values are the other way round, i.e. positive for attitude and negative for gyro. help 😊

[@matthewsumner9398]

I have a DX9 controller a Align 470LM helicopter with a microbeast plus ver 4.2 and I can’t get the attitude control to work. How do I get to parameter L in the parameter setup? Every time I get to L it ends the menu and exits parameter menu. Am I doing something wrong? Do I still Have to down load something to get attitude control to work? The helicopter flys great it’s all working but I can’t get to parameter menu L to turn on Attitude control. I’ve searched all over for anyone that knows your the only one I found That has the know how. ThAnks, Matt

[@canadiandronepilot7535]

Thomas I just came across this video ! Thank you - What Spektrum USB interface are you using to connect tree BeastX to computer ? Thanks

[@DesertJeff]

Does all this information still hold true today? September 19th 2019

[@chriswilliams78601]

Hi Tom... any plans on making a tutorial from start up to your curent video. I have a Spektrum DX18 also removed myoriginal ar7200 from my blade 360cfx installed a Beastx plus purchased the V4 update now having a rough time figuring out initial setup. lots of info but all in German....

[@quicknickk]

+Chris Williams Hi there. Yes. I have done the same. Replaced my AR7200BX with nitro govenor to BeastxV4. Very expensive paying for it in Rands. (R1817) BUT now, it says using a standard receiver (AR8000) I cannot enable the menu N for the nitro Governor? To be able to use the nitro Governor I need to use a satellite receiver. BUT now, in the manual it says NOT to use just the satellite for anything bigger than a 450 because of its range. So therefore you can only use the governor on a 450? So very disappointing at this stage. Dont know what to do from here for governor. ANY HELP?

[@edsonnagatomo]

Usa o bec para Helicópteros elétrico?

[@salines70]

then activating att. control the plate tilts left little, you know, the motiv?

[@scottbuck9348]

Hey is it possible to buy that attitude version and download it on all 4 of my microbeasts. Cause 110 bucks is pretty expensive. I think I only spent 100 on the unit itself! The only way I could see myself buying is if I could use the software on all my helis???? Anybody????

[@MichaelHeliGuy]

Hi Thomas, Great video. One question: where did you see that a factory defaults reset was required? I saw your reference to the page 14 receiver setup. I also see a reference to review all the "Setup menu points" after the update on page 17 and to only do a factory defaults reset if you felt unsure all the steps were followed correctly. I recently did a 4.x -> 4.2 pro purchase/upgrade, did the receiver setup, and reviewed all the setup and parameter menu points. All of the menu points were unchanged from their pre-upgrade values. I've flown the heli four times now and it has flown fine. Additionally, the flight training mode has worked great (I'm setting it up for my son to try). Just curious. Thanks, -Michael

[@salines70]

hi,the point M to what one sets for 3 d?

[@jctgf]

excellent video.

[@RC-Heli835]

Still no bank switching in Microbeast?

[@gusperez9817]

🎉 good job 👍

[@DesertJeff]

Yes it's still applies today. though today version 5.1.3 is out. About the same cost.

[@rtoebak76]

I,m on version 5.2.2 and i really want to get angular to work for a friend of mine. The early version 5.1 worked perfect btw. Danced like a ballerina. Now new version and the heli is nervous as you know what.

[@terenceevans4770]

Hi Nice Video you don't have share your Bailout with gyro even if you have a 6 channel rx as it defaults to aux 2 in your radio channel

[@NAVYABHAN]

Do you build helicopters? I have the Align T-Rex 450L with the Micro Beast Plus!

[@Nytro97]

Good job !! Thanks

[@crystalhelix]

You should take some videos of your skills flying these things.

[@salines70]

Thanks Tom

[@mohammadiqtidarghias7083]

Thanks

[@wildgoobsid5]

Charging anything for a software update is ridiculous. Not impressed at all with MICROBEAST. Threw mine out and bought an IKON2.

[@pauliether.c.guy.3349]

Thanx Tom your the best i struggled setting up the beastx gyro. You see I have a Tgz-380 which is a beastx clone. it has the the same exact functions as the German man beastx even the same little cheat sheet. I struggled with parameter k setting the both positive and negative pitch a 12 degrees in both directions. My problem was my helicopter would spin uncontrollably in circles. I had too much pitch in both directions not realizing it had to be between 11-13 degrees no more than 13 degrees.Oops stupid me. As soon as i set it up like you the spinning stopped with the exception of reversing the gyro. Now my next problem is how do you lock the preferred pitch into your gyro? I know it's done on the stick of your transmitter but how do you do it? do you press left or right up or down it can be frustrating. The only reason why i chose a beastx gyro is because you dont need a computer to set it up which I love unlike many other gyros such as the Align flybarless, Ikon2, Mikado Vbar, Zyx by Tarot. et Can you please help Tom? Thanks.

[@FoxMulder_]

Thanks