You are good professor. The lecture you uploaded helped me to design array antenna. Thanks for sharing good lecture.
@dr.hariprasadnaikbhattu Жыл бұрын
Thanks for the Support
@lostsoul1212Ай бұрын
very helpful made this as my mini project your video saved us 😍🥰🥰🥰🥰😍😍🤩😘😘😍🥰🥰
@dr.hariprasadnaikbhattuАй бұрын
You are welcome. Thanks for the update
@muhammadfasihwaheed79352 жыл бұрын
Thank You Dr, This tutorial has been of great help
@dr.hariprasadnaikbhattu2 жыл бұрын
Thanks very much 😀
@yugendermood61013 жыл бұрын
nice explanation....
@dr.hariprasadnaikbhattu3 жыл бұрын
Thanks
@SENTHILKUMAR-dc3li2 ай бұрын
Video very helpful. Can you put a video for Ferrite Phase Shifter design simulation and S-Parameters. Thank You.
@dr.hariprasadnaikbhattu2 ай бұрын
Hi, I not in antenna now a days.
@raghvendradubey322811 ай бұрын
Very good Dr. Bhattu
@dr.hariprasadnaikbhattu11 ай бұрын
Thanks 🙏
@juwonelelu7931 Жыл бұрын
Hello Sir! I was wondering in 9:34 of this video how did you go about determining how much of the patch you had to cut out? was there a technique/formula to this or did you just assume the amount to cut. Similarly, did you assume the length and width of the feed you attached, or is there an equation to determining this. Thank you!
@matheuscardozo1865 Жыл бұрын
Hi, if you find away to calculate this parameter, can you share it here? I'm facing the same problem in my project!
@juwonelelu7931 Жыл бұрын
@@matheuscardozo1865 Sure! same for you
@rrxn Жыл бұрын
Hi! I'm wondering this exact same thing as well!
@dr.hariprasadnaikbhattu Жыл бұрын
Hi, I was told about this in a online workshop.
@Sk106962 ай бұрын
Can you share the approach as I have same issue
@nishantmore28 күн бұрын
Thank you sir.❤
@dr.hariprasadnaikbhattu27 күн бұрын
You are Welcome
@gurumiya2 жыл бұрын
hello sir. it's really helpful video! i wonder how did you get the feeding length (30mm)?
@shingiechakoma13174 ай бұрын
from the formula of operating frequency of the microstrip patch antenna. frequency is determined by the relative permittivity of dielectric and length of patch
@nazl2273 жыл бұрын
Hello sir. First of all, your video is very helpful and good. Please can you explain us how did you calculate the radiation box dimensions?
@dr.hariprasadnaikbhattu3 жыл бұрын
Thanks for the response. I have used the radiation box dimensions as double the dimensions of x,y and z. This is to allow enough space for radiation
@nazl2273 жыл бұрын
@@dr.hariprasadnaikbhattu Thank you for answering. So how did you calculate the x, y, and z dimensions?
@dr.hariprasadnaikbhattu3 жыл бұрын
@@nazl227 substrate is rectangular/square of x=40mm by y=40mm and z=1.6mm.
@nazl2273 жыл бұрын
@@dr.hariprasadnaikbhattu Someone said "The ideal value for the size of the radiation box is calculated as λ/4.". However, I could not fully understand. How is it calculated using this?
@dr.hariprasadnaikbhattu3 жыл бұрын
@@nazl227 radiation box is a medium for radiation
@microstripantennas-dr.hala14183 жыл бұрын
Good explanation
@dr.hariprasadnaikbhattu3 жыл бұрын
Thanks
@microstripantennas-dr.hala14183 жыл бұрын
@@dr.hariprasadnaikbhattu sir thanks for the reply, my friend perchaged the HFSS software for his lab in engineering college for students, can we use that for making tutorial video like your video
@dr.hariprasadnaikbhattu3 жыл бұрын
@@microstripantennas-dr.hala1418 yes.
@microstripantennas-dr.hala14183 жыл бұрын
@@dr.hariprasadnaikbhattu thank you sir
@microstripantennas-dr.hala14183 жыл бұрын
@@dr.hariprasadnaikbhattu any upcoming tutorial video on mpa sir
@ramprasadravula48913 жыл бұрын
very good expalnation sir
@dr.hariprasadnaikbhattu3 жыл бұрын
Appreciate for the response
@vishnumuraleedharan46685 ай бұрын
Sir how to select the cut and patch at the same time
@dr.hariprasadnaikbhattu5 ай бұрын
Hi, if possible go through the video again. At video tiome 10.05 onwards
@Saranghe1333 ай бұрын
Use ctrl and select cut and patch
@enockkipkoech22052 ай бұрын
How did you come up with the dimensions of cut (9.5mm and 2.5mm)?
@dr.hariprasadnaikbhattu2 ай бұрын
Hi, I did it in a FDP. I dont know much about that. Now I am not in Antennas
@sethsanadim.s81042 жыл бұрын
sir this video is very helpful thank you. sir may I know can we fabricate patch antenna on different substrates? bcz somebody told me tht substrates are very costly(other than FR4) and unavailable in India. If you have any idea let me know even fabricators address
@dr.hariprasadnaikbhattu2 жыл бұрын
Yes, There are other substrates which are costly. In India also there are fabrications but limited.
@abouchahinemouhamad7784 Жыл бұрын
Dear Dr. HariPrasad, Do you know plz how to redefine the dimensions of volume obtained by a sweep of a surface over a line path like we can redefine the starting points and the dimensions of a box after creating it? Best Regards,
@dr.hariprasadnaikbhattu Жыл бұрын
Hi, don't know about it.
@generallifestyle62014 ай бұрын
sir at 10.17 how did you subtract cut from patch like how how did you select those two together for substraction
@dr.hariprasadnaikbhattu4 ай бұрын
Hi, first select one structure then press cntrl or shift key on keyboard to select another
@hus_8s2 жыл бұрын
Thank you very much sir, may I ask how you optimize the Freq at 2.4 GHz.
@dr.hariprasadnaikbhattu2 жыл бұрын
Use this video for optimization kzbin.info/www/bejne/nnzIlYCDdp6nqNE
@hus_8s2 жыл бұрын
@@dr.hariprasadnaikbhattu Thank you very much, Dr.
@cadcaetutorial2039 Жыл бұрын
So nice this videos
@dr.hariprasadnaikbhattu Жыл бұрын
Thanks
@manum92358 ай бұрын
Finally minute result--- create far field report---- rectangular plot option is pressed, so open a window there is no "sweep" option, the laptop is windows 11, so last graph is not available, what is the reason?
@dicaprio56178 ай бұрын
Redo
@dr.hariprasadnaikbhattu8 ай бұрын
Thanks
@dr.hariprasadnaikbhattu8 ай бұрын
Redo the simulation process
@prateekyadav4603 Жыл бұрын
Hi can you plz help me in providing port excitation. Am not able to create line and the following steps.
@dr.hariprasadnaikbhattu Жыл бұрын
Hi, once port is created. Assign lumped port. You see a small triangle shape then draw the direction
@prateekyadav4603 Жыл бұрын
@@dr.hariprasadnaikbhattu sir after selecting the rectangle and the assigning port my menu is different than the video it just assign port name nothing else
@prateekyadav4603 Жыл бұрын
After that if i go to excitation i get no option to create line
@SukruthKrАй бұрын
sir at what frequency it is designed....?
@dr.hariprasadnaikbhattuАй бұрын
It is designed at 10 GHz frequency
@PRANAVMAHAJAN-yg6do3 ай бұрын
Sir, i dont see the lumped port option for Assigning Excitation to the port. Is it because i am using a different version HFSS (Ansys Twin Builder Student 2023 R2)? please halp/
@dr.hariprasadnaikbhattu3 ай бұрын
It may be the reason
@mpkdon3 ай бұрын
can we do this in student version? currently im also having the same as urs
@kh8803 Жыл бұрын
Hii Is this design can also be used for mm wave filtering antenna.. Please can anyone tell..
@dr.hariprasadnaikbhattu Жыл бұрын
Yes
@AbderrahmaneBenhalima Жыл бұрын
hello dr, i hope you're doing well , thank you so much for the video , i've a question one about this video and one about a problem that i faced , first question , how to optimize the frequency in same case as in this video ? 2nd question ,i designed an antenna and i find that the input impedence is more than 50 ohm , it's about 160 ohm how can i optimize it too ? And thank you so much
@dr.hariprasadnaikbhattu Жыл бұрын
These may be helpful kzbin.info/www/bejne/nnzIlYCDdp6nqNE kzbin.info/www/bejne/n3y7pp2riJyCnKs
@BECSachinAravinthK5 ай бұрын
Sir, I would you to have (1.6,0.8,3.2 ) as a standard value, Is there any data sheet for that?
@dr.hariprasadnaikbhattu5 ай бұрын
Hi, as per my study and research industrially also 0.8, 1.6 , 3.2 thickness substrates are used widlt
@tadoorisharvani5704 ай бұрын
sir can u tell the feed width if i take the substrate as isola-speedISCR of dielectric constant 3.3
@dr.hariprasadnaikbhattu4 ай бұрын
Hi, feed width remains same even if dielectric is changed
@mohammadmehaboob70552 жыл бұрын
Thanks for the video sir, is it possible to change the material of the patch? As in instead of assigning it a boundary of Perfect E , we can assign some other material instead?
@dr.hariprasadnaikbhattu2 жыл бұрын
Yes, you can
@mpkdon3 ай бұрын
@@dr.hariprasadnaikbhattu how
@shabnamparween83853 жыл бұрын
Thankyou so much sir for this informative video. Kindly suggest me Which software is suitable for simulating antenna and Rectifier in one single software for rectenna design? Please recommend.
@dr.hariprasadnaikbhattu3 жыл бұрын
Thanks for the response. Antenna can be taken as source. Apply to the rectifier circuit. Use Advanced Design System tool.
@Theoer Жыл бұрын
Hello sir. Thank you for this helpful video. Can you inform about the polarization of this antenna and is it possible to use it in any kind of 4G communication systems?
@dr.hariprasadnaikbhattu Жыл бұрын
Hi Thanks for your response. I don't know about polarization in antenna.
@shantughose286410 ай бұрын
Hi, do you have any video of circular loop for CP polarization technique?
@dr.hariprasadnaikbhattu10 ай бұрын
No I don't have video on that
@rameshangadala14553 ай бұрын
Sir for rogers RO4003 what is the length and width of feed and port could you please give the values sir
@dr.hariprasadnaikbhattu3 ай бұрын
Hi, no separate values it totally depends on epsilon during design. See at the start of designing
@shivabandaru497 Жыл бұрын
Sir iam getting 3d model red mark in validation check
@dr.hariprasadnaikbhattu Жыл бұрын
That's means you have not designed properly or missed any of the steps
@dharshan13057 ай бұрын
sir what to provide as Zo and electrical length since they are 2 new fields in the calculator
@dr.hariprasadnaikbhattu6 ай бұрын
Hi, I could not get your point
@KimJames-lo7ob Жыл бұрын
Sir, How do you know that cut direction in x axis is -9.5? Please explain
@dr.hariprasadnaikbhattu Жыл бұрын
It is a rectangular patch. Decide based on that
@KulwinderKaur-kd3bk2 жыл бұрын
good explanation sir. but how-to decide the dimensions of rectangle to be cut?
@dr.hariprasadnaikbhattu2 жыл бұрын
I have taken from a video tutorial
@alugojuanuhya53109 ай бұрын
sir how to reslove the problem when the boundaries and excitations are invalid
@dr.hariprasadnaikbhattu9 ай бұрын
Hi, Not much information about this question.
@preethaasokan64065 ай бұрын
Sir ,how to design 2*2 patch antenna array
@dr.hariprasadnaikbhattu4 ай бұрын
kzbin.info/www/bejne/bXW3aJeld8dloc0
@microstripantennas-dr.hala14183 жыл бұрын
For using HFSS for such tutorial sir any copyright issues
@dr.hariprasadnaikbhattu3 жыл бұрын
It is a commercial tool.
@yennamveni37902 жыл бұрын
Sir, what if i want to design some other designs like star,ovel,some alphabets on substrate how can i calculate the velues
@dr.hariprasadnaikbhattu2 жыл бұрын
Use this link www.emtalk.com/mpacalc.php Based on the obtained length and width design a patch
@yennamveni37902 жыл бұрын
Thank you sir
@BillyBustamante2 жыл бұрын
How do you optimize antenna to get S11 at 2.4GHz? What i have to change?
@dr.hariprasadnaikbhattu2 жыл бұрын
Hi Set the width of antenna as variable. Perform parametric analysis
@424bupurumadhu65 ай бұрын
Hlo sir you have document for this project,if you have send me sir
@dr.hariprasadnaikbhattu4 ай бұрын
Hi, I dont have that project file.
@shaikzaheera8119 Жыл бұрын
sir it is not able to select the CUT and PATCH simultaneously.....how to select both simultaneously
@dr.hariprasadnaikbhattu Жыл бұрын
Hi, it is possible Select Patch first then use shift/ control key and select Cut.
@shaikzaheera8119 Жыл бұрын
@@dr.hariprasadnaikbhattu yeah sir got it...tqsm😻
@user-zh9vi2nz6e4 ай бұрын
can we increase or decrease the gain of antenna?
@dr.hariprasadnaikbhattu4 ай бұрын
Yes, by adjusting the length and width or through optimisation
@ECAmitkumarSharma Жыл бұрын
Hi sir , how did u calculated the xsize and ysize to cut
@dr.hariprasadnaikbhattu Жыл бұрын
Hi, I did it based on tutorial I have attended
@prabha__4146 ай бұрын
Excuse me sir Please provide a video on this design Reconfigurable Structure Reutilization Low-SAR MIMO Antenna for 4G/5G Full-Screen Metal-Frame Smartphone Operation
@dr.hariprasadnaikbhattu6 ай бұрын
Hi, not working on Antennas
@shahriarrami4096 Жыл бұрын
Dear Dr.HariPrasad Would you send me or share the link of this paper? Thank you,
@dr.hariprasadnaikbhattu Жыл бұрын
Hi, It is not from paper. I learnt the design through a workshop.
@AnushaYadav01 Жыл бұрын
How to create the lumped port part even after changing the XZ it is drawing as a rectangle not as an arrow
@AnushaYadav01 Жыл бұрын
Sir please tell
@dr.hariprasadnaikbhattu Жыл бұрын
Select the port Right click Assign Lumped port
@AnushaYadav01 Жыл бұрын
@@dr.hariprasadnaikbhattu Sir, after assigning to the lumped port I'm not getting the box like you got which is 50 ohms and the new line option also I'm not getting it
@jas_n1580 Жыл бұрын
@@AnushaYadav01 Im getting this same thing too. It does not proceed to the arrow cursor
@rrxn Жыл бұрын
Same here, could anyone reply here if they get the solution to this?
@saiswaroop35702 жыл бұрын
Sir, Please tell how to learn HFSS design from basics .
@dr.hariprasadnaikbhattu2 жыл бұрын
HI sai, it is a basic patch antenna design in hfss.
@saiswaroop35702 жыл бұрын
@@dr.hariprasadnaikbhattu Ok sir , Please tell how to learn HFSS.. any Sources.?
@devvratkrishna6215 Жыл бұрын
Sir I have excel data for co & cross polarization of E plane & H plane but I am unable to plot it in origin can you please help me.
@dr.hariprasadnaikbhattu Жыл бұрын
Don't know exactly about it.
@prin_tejash Жыл бұрын
sir can you pls share the mechanism of how to design a terahertz anteena in hfss
@dr.hariprasadnaikbhattu Жыл бұрын
Hi, I don't know much about it.
@akhilab9715 Жыл бұрын
for me s parameter is not listed in the reports section
@dr.hariprasadnaikbhattu Жыл бұрын
I could not get your point
@amrithmahesh54488 ай бұрын
How to calculate the dimensions of the ground
@dr.hariprasadnaikbhattu8 ай бұрын
Hi, it need to be decided what length and breadth of antenna to design
@manishtomar71622 жыл бұрын
sir can u upload the video regarding designed and simulation of dual band mimo antenna for 5g application using hfss
@dr.hariprasadnaikbhattu2 жыл бұрын
Sir right now I am not working on Antennas
@314neel2 жыл бұрын
Hello, nice video I was wondering where I could find the file?
@dr.hariprasadnaikbhattu2 жыл бұрын
Hi, I have designed the antema.
@314neel2 жыл бұрын
Could you please mail me the file?
@yavuzciftci7989 Жыл бұрын
Sir how did you calculate the length of cut and feed line
@dr.hariprasadnaikbhattu Жыл бұрын
Hi feed line is from (0,0). Not much info about cut. Becoz i learnt from a online course.
@yavuzciftci7989 Жыл бұрын
@@dr.hariprasadnaikbhattu thanks l found out it.
@itisallaboutmusic2459 Жыл бұрын
@@yavuzciftci7989 can u tell me how please
@b43_yashusoni86 Жыл бұрын
Sir make video on fss in Mimo antenna
@dr.hariprasadnaikbhattu Жыл бұрын
Hi, I may try but not sure
@kivenyllow32643 ай бұрын
For the cut, how to know the width of the cut?
@dr.hariprasadnaikbhattu2 ай бұрын
Hi, I did it in a FDP. I dont know much about that
@kivenyllow32642 ай бұрын
@@dr.hariprasadnaikbhattu What is FDP?
@mpkdon3 ай бұрын
im not getting peak at 0 instead im getting heartin shape 😂 😂 what might be the problem
@dr.hariprasadnaikbhattu3 ай бұрын
Hi, check the excitation port
@akashsharma2602 Жыл бұрын
My lumped port is not working properly reference conductor for terminal
@dr.hariprasadnaikbhattu Жыл бұрын
Actually change the access to XZ
@akashsharma2602 Жыл бұрын
@@dr.hariprasadnaikbhattu ok thanks
@shivi6636 Жыл бұрын
@@akashsharma2602 same problem can you help me?
@akashsharma2602 Жыл бұрын
@@shivi6636 just go to hfss then click solution type then select terminal option and click ok good luck for your project
@shivi6636 Жыл бұрын
@@akashsharma2602 thank you but in my case it worked for modal option.
@professionaluse57022 жыл бұрын
Sir How did you select patch and cut at a time?
@dr.hariprasadnaikbhattu2 жыл бұрын
Patch width and length is calculated at the starting.
@keerthanamv51322 жыл бұрын
Control+patch and cut
@anusreet9452 Жыл бұрын
What about electrical length?
@dr.hariprasadnaikbhattu Жыл бұрын
It is designed with quater wavelength
@swethamanupati7564 Жыл бұрын
Hello sir, can you please help me to design an patch antenna at 300GHz
@dr.hariprasadnaikbhattu Жыл бұрын
Hi right now I am not working on antennas
@prernasingh49442 жыл бұрын
Hello Sir . I want to simulate conformal antenna. Can you help?
@dr.hariprasadnaikbhattu2 жыл бұрын
I am not working on antenna.
@sdemartur98042 жыл бұрын
Sir, from where can I get this software. Please help
@dr.hariprasadnaikbhattu2 жыл бұрын
It is a Commercial tool not a free tool.
@UmarAshraf22 ай бұрын
Ye kon sa software hai sir ???
@dr.hariprasadnaikbhattu2 ай бұрын
Hi, this is antenna design software HFSS
@koukyshooky40923 жыл бұрын
hello sir i want to know if we can simulate a microstrip multi-patch antenna
@dr.hariprasadnaikbhattu3 жыл бұрын
Not right now.
@koukyshooky40923 жыл бұрын
@@dr.hariprasadnaikbhattu please sir explain us and do a tutorial about it
@saikrishnaanem76172 жыл бұрын
Hello sir how to select patch and cut at a time to subtract?
@dr.hariprasadnaikbhattu2 жыл бұрын
Select both the cut and patch and perform the boolean operation. Like Unite, Subtract...
@sabrinaakthar2011 Жыл бұрын
Use ctrl + A and select patch and cut
@vangapandupraveen43528 ай бұрын
can you please design micostrip patch antenna at 16.5ghz
@dr.hariprasadnaikbhattu8 ай бұрын
Hi, I am not working on antenna now
@kalyannelli58343 жыл бұрын
Sir when you cutting the feedline to provide the proper impedance matching to the patch, then how you get the calculation values
@kalyannelli58343 жыл бұрын
Sir plz tell us how the cutting values are came
@dr.hariprasadnaikbhattu3 жыл бұрын
@@kalyannelli5834 patch has edge impedance of z=240 ohms. So use the inset feed to balance the impedance to z=50 ohms. So started the feed in x direction.
@kalyannelli58343 жыл бұрын
@@dr.hariprasadnaikbhattu Yes sir! but how the X and Y size values are taken in tutorial you had taken X=14.7 and Y = -2.5
@kalyannelli58343 жыл бұрын
@@dr.hariprasadnaikbhattu sir PLZZ tell me how you taken the cutting values of Xand Y.
@mpkdon3 ай бұрын
@@kalyannelli5834 you can get formula from google
@mohammedsalem608511 ай бұрын
How can I contact you ?
@dr.hariprasadnaikbhattu10 ай бұрын
What's the need
@mohammedsalem608510 ай бұрын
@@dr.hariprasadnaikbhattu design antenna by HFSS 13
@dr.hariprasadnaikbhattu10 ай бұрын
@@mohammedsalem6085 I am not working on antenna now
@mukulchaoudhary53692 жыл бұрын
Sir how to select patch and cut for subtraction please help
@dr.hariprasadnaikbhattu2 жыл бұрын
Patch width and length is calculated at the starting.
@tejasrathod837 Жыл бұрын
I am not able to see option to add lumped modes on the excitation port. please help @
@rrxn Жыл бұрын
I'm having the same issue. It isn't letting me choose the impedance value in the 2023 version
@dr.hariprasadnaikbhattu Жыл бұрын
I don't know about 2023 version
@BAKKABBAI2 жыл бұрын
Bhattu sir where are you from
@dr.hariprasadnaikbhattu2 жыл бұрын
Hi I am from Telangana
@pujariranjithkumar4138 Жыл бұрын
Which version hfss software sir
@dr.hariprasadnaikbhattu Жыл бұрын
It is 2019 version
@Zaki-sx9kt3 жыл бұрын
hello please can you explain us how did you calculate the cut parameter?
@dr.hariprasadnaikbhattu3 жыл бұрын
Depends on the feed length impedance. Z decreases as we go deep.
@cadcaetutorial2039 Жыл бұрын
Weldon
@dr.hariprasadnaikbhattu Жыл бұрын
Thanks
@ShrutiJaiswalEC Жыл бұрын
Sir mera gain negative aa rha
@dr.hariprasadnaikbhattu Жыл бұрын
May be feed not connected properly
@kokkondapravalika37833 жыл бұрын
How to calculate x size of the feed and x size y size of cut and postions of cut?
@dr.hariprasadnaikbhattu3 жыл бұрын
Patch has edge impedance of 240 ohm. So use a deep cut for impedance matching from the origin
@pranavreddy39992 жыл бұрын
Hai sir can u tell abstract of these
@dr.hariprasadnaikbhattu2 жыл бұрын
freq=2.4GHz, Er=4.4, H=1.6mm, W=38mm, L=29.4mm
@HabibaKhatun-j5l7 күн бұрын
Perez Laura Smith Michael Young Michelle
@dr.hariprasadnaikbhattuКүн бұрын
What that means.......
@sdemartur9804 Жыл бұрын
Sir, is HFSS working on android 11 version tablet ,.
@dr.hariprasadnaikbhattu Жыл бұрын
Hi It works on PC not on Android
@paanibasina70063 жыл бұрын
How do we calculate the X size of cut rectangle??
@dr.hariprasadnaikbhattu3 жыл бұрын
It actually depends on feed line impedance
@Cricketlovers105262 жыл бұрын
Sir I need your help
@dr.hariprasadnaikbhattu2 жыл бұрын
Hi. In what way I can help.
@reddylakshmisunitha4951 Жыл бұрын
Tq sir
@dr.hariprasadnaikbhattu Жыл бұрын
Thanks 👍
@reddylakshmisunitha4951 Жыл бұрын
Sir,how Can i save images directly in software or take screenshots
@dr.hariprasadnaikbhattu Жыл бұрын
@@reddylakshmisunitha4951 use save or export image option
@reddylakshmisunitha4951 Жыл бұрын
@@dr.hariprasadnaikbhattu ok sir tq so much sir
@reddylakshmisunitha4951 Жыл бұрын
@@dr.hariprasadnaikbhattu sir how to stop simulation before analysing the s-prarameter plot
@sreyas5861 Жыл бұрын
18:12
@dr.hariprasadnaikbhattu Жыл бұрын
At that time simulation is performed.
@mistercutie59152 жыл бұрын
Sir jee dabba bhaag raha hai
@swalimusthu17803 жыл бұрын
H h
@nsgsonu3420 Жыл бұрын
Evuuu
@dr.hariprasadnaikbhattu Жыл бұрын
What is that
@beaughosh17392 жыл бұрын
Sir, I have problem in bending of antenna. Can you please give me your email id ?
@dr.hariprasadnaikbhattu2 жыл бұрын
I could not get your point.
@beaughosh17392 жыл бұрын
@@dr.hariprasadnaikbhattu Sir I want to do bending analysis of antenna how to do it I need your help
@dr.hariprasadnaikbhattu2 жыл бұрын
@@beaughosh1739 I really don't know about it.
@beaughosh17392 жыл бұрын
@@dr.hariprasadnaikbhattu ok sir.thank you.
@user-xo7vt4fs2y Жыл бұрын
Please write your email
@D.I.V.I.N.E4 ай бұрын
sir how can we design microstrip patch antenna for 5g communication
@dr.hariprasadnaikbhattu3 ай бұрын
Hi, antenna design depends on the frequency. Based on frequency decide whether it is for 5g or other
@D.I.V.I.N.E3 ай бұрын
@@dr.hariprasadnaikbhattu sir it frequency is 28Ghz
@D.I.V.I.N.E3 ай бұрын
@@dr.hariprasadnaikbhattu how to find the dimensions of antenna
@daryenplays4148 Жыл бұрын
hello sir i'm not able to add lumped port while clicking on excitation lumped port it's give reference conducter for terminals....please help me out
@dr.hariprasadnaikbhattu Жыл бұрын
Hi, to add the lumped port change the grid to YZ plane. Use lumped port
@daryenplays4148 Жыл бұрын
Sir l I'm not able to do it...its Still ask for Reference Conductor for terminal while i click on Lumped port
@dr.hariprasadnaikbhattu Жыл бұрын
@@daryenplays4148 hi, try to follow the video once again.