MIKE !!! You are a life saver. I have 1979 ford. Felt a little overwhelmed after I broke the carburetor down. Your detailed explanation saved my bacon. My truck has never ran so smooth in the 6 years I have had it. Thank you for posting this.
@mphilleo2 жыл бұрын
I'm about to rebuild the YFA on my 1974 Ford Maverick. My shop manuals will arrive AFTER the carb kit does, so this is a life saver!
@mphilleo2 жыл бұрын
@@MikesCarburetor, darn it! I might have to order that kit from you guys.
@roblamar21726 жыл бұрын
Thanks for the videos Mike! Mine had a lot more electronic crap on it but essentially the same on the inside. These videos got me through it. Thank you!
@ChristopherL0rtiz2 жыл бұрын
Only a man very confident and very knowledgeable can take these things apart so quickly without any hesitation. I still haven’t taken my carburetor off the block 😂
@bryanchild5578 жыл бұрын
Hey Mike, A couple of weeeks ago my carb started to flood on my 82 Ford F250 after i installed a fuel pump. Any way...long story short, never rebuilt a carb, furthermore, never really looked at one...I watched your videos, followed them, and ended up with a nice, rebuilt carb that runs great!! Thank you, Thank you!!!!
@bigboyzguns81644 жыл бұрын
watched your video, ordered your rebuilt kit, rebuilt the carb. easy peasy. Thank you.
@knucklehead42336 жыл бұрын
I like the way you shake it and parts fly off so we know exactly where they came from...
@ooCHICOoo Жыл бұрын
great 👍 video so thank you for sharing my friend 😊
@MikesCarburetor Жыл бұрын
Thank you for commenting.
@DarkPrince01311 жыл бұрын
That bracket @15:05 is for the "WOT" sensor that connects to egr valve which you can see the wot is still attached to the bracket. Hope that helps someone.
@WL-mt4mv Жыл бұрын
The main design flaw of the YFA is the accelerator pump sits in the bottom of the fuel bowl with engine vacuum on the other side. If you get a hole in the diaphragm the engine will run extremely rich. With a full fuel bowl, it will drain into the intake manifold just sitting there.
@bobshove41110 жыл бұрын
If you have a YF early 50's the gasket mikes sends also fits the yfa. They don't send you the exact gasket that was original, because they save money by not having that orig one, so they send one that has a hole in it and there is a small gasket left like 1/8 so don't be alarmed, it works..
@sailingradmode9473 Жыл бұрын
Hmmm...pretty sure I am missing the check ball and I KNOW I need a new bushing for the throttle shaft that goes through the throttle body. Would I be able to purchase these two parts by themselves?
@dvddmc11 жыл бұрын
Ah I see that's where the two screws are that are where the throttle cable connects too
@claytonstanger535211 жыл бұрын
i was pulling that exact same carb off a 1984 ford f150, and not thinking, broke the fuel line because i was twisting the bottom end of the fuel filter
@ChristopherL0rtiz2 жыл бұрын
Did all of those YF carbs come with what I think is called a ‘idle stop solenoid’? I’m not sure if the verbiage is right however my particular carburetor has one. Is not hooked up does it need to be? If it’s not and or removed what problems may occur?
@8.2deck Жыл бұрын
I have an 86 2.3 n/a mustang with a yfa feedback system. I want to ditch the computer controlled system. Do you think a yfa from a 300 six would work well on that engine? I also changing the ignition system to a regular distributor with mechanical and vacuum advance.
@ronsmith36077 жыл бұрын
what all tools and sizes did you use on this carb mainly the socket bits type and sizes
@brockmay39902 жыл бұрын
Just installed an electric choke version in my 83 Bronco I6. Can’t get it to stop surging. Any ideas?
@misaelmedinacarburacion6 жыл бұрын
SI NO ME EQUIVOCO ESE CARBURADOR ES DE HENRY
@JoseRodriguez-nl7no4 жыл бұрын
Misael Medina Carburación y Fuel Injection amigo tu me podrías guiar para afinar ese tipo de carburador?
@MrTaxmaniac11 жыл бұрын
Rebuilt an early model of the yfa, 6552s on a 1972 CJ5. Wasnt sure whether the larger check ball went in the diaphragm housing or in the body with the check weight under the gasket. There was no hose from housing to carb. Jeep idles and runs fine when level but bucks and stalls on steep incline. Could that be a metering rod or float adjustment?
@ronaldtober944310 жыл бұрын
Same carb on my truck ,I broke it down to rebuild because runs good except after setting the carb goes dry , any thoughts
@MrTaxmaniac11 жыл бұрын
Will you be getting more metering arm assemblies with the adjusting screw? Mine does not have the screw and I'm not certain how to bend the bracket. Also, when you say large ball in main discharge. Is that the ball over the diaphragm? Thanks.
@GoodOldMike5 жыл бұрын
I suspect I need to bush my YFA throttle shaft. I have a leak right in that area. Do you sell a kit for this specific issue?
@WubiWatkins2 жыл бұрын
Hey Mike I have a question I've got the carburetor the YFA that you're showing and my throttle position sensor screws and stuff were not on there but I've seen pictures I'm missing the little yellow cap and the screw that goes in the throttle rod to hold the washer on what are those called and where can I buy them.
@WubiWatkins2 жыл бұрын
@@MikesCarburetor does the slotted washer go up, down, which side?
@latamorewilliams6443 Жыл бұрын
Mr Mike can I clean my yfa carburetor parts with pinesol? Also how do I set the carburetor once installed 😇🤝?
@latamorewilliams6443 Жыл бұрын
@@MikesCarburetorhow long is appropriate mr Mike? And thank you😇😇🤝
@latamorewilliams6443 Жыл бұрын
@@MikesCarburetor Thank so much!!!!!!😇🤝
@martinramirez95223 жыл бұрын
Hola soy colombiano no podrían tener subtitulos en todas sus explicaciones thanks
@dvddmc11 жыл бұрын
I have the same carb on my 80 f100 the idle is too low. would ijust have to adjust that idle air screw that you removed? just turning it abit??
@hailwindham9 жыл бұрын
any tips on how to get to that pesky and ill placed mounting bolt?
@Modifyre10 жыл бұрын
I rebuilt mine a while back and just put it on recently. Idle is great and throttle response is amazing but if I hold a steady RPM above 1200 it bogs after 4 or 5 seconds, then comes back and repeats. A different carb (same type) I have works not bad except it bogs when hitting the gas unless the choke is partially engaged. It needs a rebuild though so probably the accel pump is shot. Can you tell me what might be wrong with the rebuilt carb? Checked float level and whatnot, all seems to be fine.
@Modifyre10 жыл бұрын
I will rebuild it again and try that, thank you!
@DMO-DMO-DMO12 жыл бұрын
Adjusted the cold idle screw?
@sn95roots213 жыл бұрын
Can you replace a yfa with a yf?
@olblu87463 жыл бұрын
Sn95roots l replaced a yfa with a yf carb. on a 69 f-100 300 6cyl. But l also replaced the intake manifold and the heat riser to the other side. I had to overhaul the yf as it had sat out on an engine for 20 years in back of my dads property. I liked the yf better , it had less things that could go wrong . A very simple but extremely efficient carb. The whole process took me 2 weeks. But when l started the truck l was extremely surprised by how smooth the engine ran. I was very happy l had decided to replace the yfa with the more simple yf carb. Another great benefit was better gas mileage! It runs great, get better mpg, same power. Although the 300 6 cyl. will never be a gas miser , l'm getter better mpg. So yeah the yfa can be replaced with a yf but you will have to work at making fit correctly to get the best out of it. A good mech. can do if you don't want any headaches. I tackled the project cause l have alot of free time. If you suceed like l did you will never look back . Mikes expertise will help you greatly. Also do what l did before and during disassembly and during the process take lots of pictures from all angles . Several times if not many l had to go back and look up the picture of disassembly cause l forgot where parts would go. Not to worry though the yf is simple , has less parts than most other carbs. The rebuid kid from NAPA cost 18.99 + tax God bless.
@ronaldtober944310 жыл бұрын
Also mine didn't have a check ball weight
@ronaldtober944310 жыл бұрын
my truck is 1986 Ford F 250
@fordinlinestraight6 жыл бұрын
Hi mike i just put on a new yfa carb on a ford f150 inline 6. The carb is. 7389s its fAst idle seems high what should it idle at start up? Do you have any sugestions cheers
@fordinlinestraight6 жыл бұрын
Hi mike i found the info it was on the valve cover. I wanna learn as much as i can from you as not to many people have knoledge of these carbs. And the younger generation doesnt really care to learn do this will be a lost art. Cheers
@loganguzman68565 жыл бұрын
+Mikes Carburetor great video Mike! hey can you please show us how to adjust the TV cable that comes from the transsmission to the carburetor? because I heard if its not properly adjusted the transsmission will burn up.
@danielcanas65653 жыл бұрын
En español si se puede
@r09027166 жыл бұрын
Nice effort, but too fast and too much non-visible for the unfamiliar. No separation of parts into groups, screws and parts scattered... Thanks anyway!