Glad to find this. The bowl fell off before I saw how the floats were inside. Had no idea. Thanks for posting this video!!
@shredofmartyrs11 жыл бұрын
I cannot thank you enough for these videos. Very clear descriptions and great camerawork. I'm getting ready to do my first carb. clean and was a bit apprehensive to take on the challenge. Definitely subscribed to your channel - thanks again!
@666Coldshadow9 ай бұрын
What a fantastic video, great camera work! Thank you
@billiejoramos-guerrerojenk88855 жыл бұрын
Very helpful, would watch again.
@TheBosshog50511 жыл бұрын
Ishobie.... you need a tip jar! Excellent videos that are accurate, informative and easy to understand! Thanks for your time.
@b01tact10n Жыл бұрын
I love watching these videos. Very good content👍👍
@randyswenson78964 жыл бұрын
Thanks for the tips and procedures. When get those parts I am looking forward to a great running Elan
@manuelsailas5516 жыл бұрын
Thanks for the vid fixed mine ;) nd for the floats on the Lil cap I used a piece of speaker wire haha works perfect cuz mine didn't have one but it's runnin amazing now
@PowerModzOfficial12 жыл бұрын
@GunsClap315 Thanks for watching and your kind words, I put a lot of time into my videos and it's nice to know they are appreciated.
@kevincorson86995 жыл бұрын
Nice n thorough. Great close-ups too! T.U.
@69bjgmopar Жыл бұрын
Nice video. My carb didnt have the little stabs you put on the bowl stems after you slide the floats on. Do you know where to get them thanks.
@brety09912 жыл бұрын
Thanks man!! My snowmobile run amazing now! thanks for the parts list and stuff!!
@chrisbuffoni4 жыл бұрын
Nice vid man! Question... I just put my carb back together, same exact carb as yours. I'm not getting fuel squirt when I pull the throttle, what would cause this?
@openwheelmanic13 жыл бұрын
Thanks for the series of posts - very informative
@PowerModzOfficial12 жыл бұрын
Check the plug, hold it where it is bogging out for a few seconds then chop turn off the ignition - look at the plug - if it is dry then you are lean and not getting enought fuel, wet and dark then too much - then go from there. did you clean the carb?
@nicolaer29893 жыл бұрын
Great video! Could you tell me where I can purchase a rebuild kit for the carb you show on this video. I have the same model and have a hard time finding the correct rebuild kit. Thanks
@PowerModzOfficial3 жыл бұрын
Here
@FrankaDith13 жыл бұрын
I like to count the turn on any jets when i take them out that way i get a starting point when they go back together ,if you have a book about them that's great too .
@PowerModzOfficial11 жыл бұрын
Glad I could help!
@meconnellan12 жыл бұрын
Thanks, clear visual instructions, like the tunes, very helpful
@ajmechanical215910 жыл бұрын
I really like your video I have watched the "whole series" is it possible to have you upload video of you uninstalling and re installing the carbs. Also maybe a video of how a carb sync is done. What bike did these come off of?
@nealestep8 жыл бұрын
where did you get your rebuild kit
@sunny627911 жыл бұрын
Thanks man. I have a little different float lever. Its Z shaped, and i think i have them in upside down. Flooding instantly. So thankyou......
@RichardFrizell Жыл бұрын
Very useful! Thank you!!!
@PHILSWINGIT9 жыл бұрын
GREAT VID NICE EDIT AND HELPFUL MANY THANKS
@MarshallBLewis3 жыл бұрын
You said to install the idle screw loosely, so it really doesn't matter to be accurate with it? Is that something you adjust once the sled is running?
@slickrick91529 жыл бұрын
@PowerModz I have a dt 175 Yamaha dirtbike that runs a mikuni vm 24 and it's definetly out of sync how drastically would this effect the running because my bike runs like crap. It's starts and that's it. There's videos on my channel of it running if you need to see it in action
@uvkvk7 жыл бұрын
Hello Thank u for ur efforts to explain such a complex topic so practically. can u pls guide me on how to get the max pick up on my Yamaha, 2 Stroke RX100 92 model? I have put new clutch plates, new piston, rebored the block to 1 step up over stock bore.,new spark plug, new air filter,new connecting rod, and did carb cleaning, also I add semi synth 2T oil (30% )to petrol . Also guide me to stop leaking oil pump. Does reed valve play any role in pick up of bike? pls.
@PowerModzOfficial13 жыл бұрын
@kmtischer I'll try to do that - I don't have the tool but might get the guys at the dealership to help out.
@ryon6317 жыл бұрын
Good video. But the bottom of the throttle slide has a flat side and a arch bottom on the other side. Which side does the flat face? Filter or intake? Thanks.
@adamtoth74744 жыл бұрын
You dont use any kind of lube for the moving parts? Or the choke valve? It has a rubber grommet on it. Silicon spray or something ?
@aubs80265 жыл бұрын
Good video. Why is the choke not installed?
@metubeusercom11 жыл бұрын
Do we need to fill the float bowl with fuel first before reassembling it and mounting it back to the bike? thank you!
@BradtoriLockhart5 жыл бұрын
So I have the same carb I'm putting it back together but once I get it back on the throttle cable an kick it over it reves really high an wont shut off unless I kill it. I need help:( my bike is a 1982 dt100j yamaha.. Ive got the carb clean an everything els I just can't figure out the cable anything would help thank you an good video I just subbed
@AnujChamara8 жыл бұрын
Thanks for your explanation.My bike Yamaha FZR 250. i cleaned my mikuni carburator (4) and cleaned main jet,pilot jet and adjust air mixture 2.5 turns out from the closing point.My problem is 3 times failed my eco (smoke) test and result show more petrol consumption.but last years easily pass the eco test.My problem is need to reduce petrol.How can i adjust?please help.Thanks.
@legendfpv6 жыл бұрын
Your video shows an additional gasket you failed to install. Where does it go?
@98KingQuad5 жыл бұрын
How does the float needle seal to the seat? Is there supposed to be an o ring in the seat ? Or it is just needle valve touching the seat. Mine leaks like crazy
@PowerModzOfficial12 жыл бұрын
@GunsClap315 Hmm, not sure what the settings are for the 670 - check the online manuals and go from there.
@johncaudle14136 жыл бұрын
Wiring 198o dt 250 Yamaha
@MarshallBLewis3 жыл бұрын
For the air screw, is it tighten all the way in and then out one complete revolution?
@txryder799 жыл бұрын
@PowerModz What would you think is a good starting point for the air jets. I have a 79 TX 340 and it seems to like 1/2 a turn. A full turn seems to lean it out and it wont come off high idle. It seems to have a little more low end power at a 1/2 a turn but I don't want to risk blowing up.
@jaybrownbitch13 жыл бұрын
CaN you do a video on cleaning your clutch as well
@limey3r12 жыл бұрын
Awesome video thanks! Where do you usually buy your jets and other parts from?
@skigps2712 жыл бұрын
hello you mentioned that you replace the pilot jets. well they go by size. what are we measuring the length rob
@PowerModzOfficial12 жыл бұрын
usually from a local polaris dealer because he is close.
@littletoy0111 жыл бұрын
Great video . I have a question about the jets on my ac atv runs abit rich .so can you tell me how much I should drop jet size . I live in the mountain. Thanks
@davidearly848111 жыл бұрын
can you detail the connection of the throttle cable to the throttle slide. Does the retainer plate sit loose on the bottom of the spring, or does the throttle cable go through the second hole in the retainer plate. I ran it through the hole and it seems to work ok. does it make a difference?
@PowerModzOfficial12 жыл бұрын
@Fake0and0gay what kind of sled?
@PowerModzOfficial12 жыл бұрын
Awesome glad I could help!
@MrBuckkiller5512 жыл бұрын
I have a 1982 Suzuki RM 125, and the float stuck on it. After fixing carb, I accidentally bent the jet needle. Now it runs like crap, is it the bent needle? I tried to bend it back. The float dosent stick after cleaning.
@LM-zf6so7 жыл бұрын
my waverunner starts and run's good just it wants to run wide open at start up vacuum leak or what is up with this it 89 Yamaha500cc minkuni card 2 stroke.thanks
@SILLYGOOSE127 Жыл бұрын
How do i find the factory settings for a tundra lt 550f 2018 sport carburetor?
@rickhicks24455 жыл бұрын
Nice work
@samwubb12 жыл бұрын
hi I have a john deere JDX4 292 1974 snowmobile and i have a mikuni carb on it how do I adjust the jets and do you know a site to get the manifactuers specs????????
@danymiville136311 жыл бұрын
Does Mikuni carbs are stock carbs on a banshee or they are aftermarket carbs ??
@kmtischer13 жыл бұрын
Can you do a video on sync your carbs?? Thanks
@Fake0and0gay12 жыл бұрын
can you help me i took off all my gas lines and did not relize what i did and now i do not remeber where to put them so can you make a video about the gas line and stuff PLEASE
@JohnODonovan16 жыл бұрын
What mikuni model is it. There are many and in mine from a home lite 5000 generator that needle assembly is a whole other design a. That is the most complicated part which needs a lot more instruction. I can't find that video anywhere . Can anyone help please.
@PowerModzOfficial12 жыл бұрын
Must be something on -line?
@nickhyche94277 жыл бұрын
I have an old Yamaha moto 4 200 4 wheeler and I need too know how to or replace my choke it's broke at the carburetor
@SmoovMedia7 жыл бұрын
were do u get the specs for the air screw... 34 mm carb lt250 quadracer
@timmberthy4 жыл бұрын
what is a good amount to turn the air screw before starting up ? for a 440 or a 550? i dont have books or specs on hand what would be a general rule
@timmberthy4 жыл бұрын
its for a fan cooled snow machine
@mjshaheed6 жыл бұрын
Hello PowerModz, what does sync up the carb mean?
@jellojackets6 жыл бұрын
if you have multiple carbs they all need to be giving the right fuel/air mix at the right throttle position. so you sync them up to allow that.
@kevinstearns41988 жыл бұрын
i have an 87 kx 250 it wont start cold i take out the spark plug put gas in cylinder and it starts. ideas?
@eddie-g21436 жыл бұрын
Man.... i got a question....the "mikuni corp"carbs are genuine from japan or fake??????there's no "made in japan"written on them...is it?????
@metubeusercom11 жыл бұрын
ok thanks bro!
@electriceye6836 жыл бұрын
Would you normally lubricate a flow bowl gasket with oil, or no?
@PowerModzOfficial6 жыл бұрын
Douglas Lariviere i dont
@samuelsmith85766 жыл бұрын
I have gas out the exhaust side on my rm 100 can you tell me why thank
@WILLPILL312 жыл бұрын
No float?
@rogervaillant840611 жыл бұрын
Great video...thanks so much!!!!
@jacobmichels57993 жыл бұрын
I have the same exact carb, what we’re the specs for the air screw
@PowerModzOfficial3 жыл бұрын
Depends on the machine it came off
@thomashimes24132 жыл бұрын
How tight should the pilot jet be?
@PowerModzOfficial2 жыл бұрын
oh....about that much - dont do it too hard
@razputins7776 жыл бұрын
what is the specks for idle and air screw ? thanks
@90zzz096 жыл бұрын
yes i have the same question
@ryanplato49255 жыл бұрын
I've always been told a turn in a 1/2 to start
@alyssalocklear28447 жыл бұрын
i got a 250 trail blazer an its popping at full throtle wat does that mean
@MadeofSpareParts247 жыл бұрын
you are running to lean.
@MadeofSpareParts247 жыл бұрын
you are running to rich.
@JS-fb6ww6 жыл бұрын
Pleeeeaaaaase help. I have a mikuni vm18. I removed the 4 screws on the float bowl. I cannot for the life of me separate the bowl fro the upper half of the carb. It's like it's superglued on there even with the gasket. I cannot rejet until I seoate the bowl. Any advice????
@69bjgmopar Жыл бұрын
Have a 34 mikinu cant get the float to stop leaking by.
@PowerModzOfficial10 ай бұрын
its your needle and seat]
@shakes73335 жыл бұрын
Wait....I just watched this same exact video on another channel......🤔