Milwaukee M18 onefhiwf34 problems and repair

Рет қаралды 38,870

Күн бұрын

I have two milwaukee m18 onefhiwf34 Impact Wrench. one with electrical problems and one with cracked house and bad rotor bearing. quick repairing and service.
#norway #milwaukee #impact #power #workshop #wrench #problems #service

Пікірлер: 42

@havardjohansen6680 3 жыл бұрын

Great vid. Keep on making more 👌👌

@BogdanMRL Ай бұрын

Mine is almost new and after using a few extensions and holding it on for a few seconds it stopped working😢. Now it only turns slowly just like yours. What should I check? It out of warranty but only used twice!

@JD-ov7hk Жыл бұрын

Hello i have a m18 onefhiwf12 with the same electrical problem 0:26 did you catch were was the problem i have taken it back to Milwaukee for the second time they have been good with the warranty, they have fixed it but they haven’t caught the problem

@bacardii95 Жыл бұрын

Hello. Don't know exactly what the error is. But I think there might be some problem with the controlboard. Or a break in one of the coils in the stator. so it doesn't get the current it needs to pull the rotor around in high speed.

@gilbertocastillo7685 Жыл бұрын

Buenas noches me gustaría saber cómo van los balines de un impacto Milwaukee

@zachvargas122588 2 жыл бұрын

At 2:42 “more problems” those wires do not need to be connected to that black board, because when you re-assemble it appears that they are not connected

@richardkan8499 3 ай бұрын

At 7:42 you might have forgotten to put the ball bearing back in at the bottom of the anvil?

@cristianortiz8297 2 жыл бұрын

Can you please explain what was the problem with the electrical faulty one. Was it the rear rotor “back cover” assembly?

@bacardii95 2 жыл бұрын

Hey. I did not find out what was wrong with the electronics. but most likely the fault was with the components around the rotor.

@kurtanorbert Жыл бұрын

I can, I just repaired one of these machines. There is a black cable in the back of the housing, it meant to touch the metal part, to make electric contact. If it's weared, then the machine produces this kind of problem. I've soldered some tin to the plate on the end of the cable and it solved the problem.

@gregorioalmanza9313 Ай бұрын

@@kurtanorbertI will be trying it out..

@ТарасКохан-т4к Жыл бұрын

Hi friend. tell me please what about that board which calls ref coil/sens coil in impact body? you put it in 7:38. what it work for? do i need to solder it to wire? waiting your answer bro!)

@bacardii95 Жыл бұрын

Hello. I don't know what it does, maybe it has some function as a rev counter. but apparently it doesn't need to be connected when you use setting 1,2,3

@РоманГородиський-у7ж Жыл бұрын

Hi. Can u show me how i need solder wires on that board? 7:38 because in the 4th position it does not have the power to unscrew.

@crazylizard92ify 4 ай бұрын

What did you use to clean the tools?

@bacardii95 4 ай бұрын

Breake cleaner

@luckyhack78 Жыл бұрын

unacceptable for the price, if it was Parkside it can be normal after use it every day for two years

@serviciomecanicoeljavi2799 2 жыл бұрын

hola amigo tengo una de asa pistola xk ahora n tiene la misma fuerza se quemo un dispositivo en la plaqueta d la bateria y sele iso puente directo sera k puede ser la bateria

@abbershayhalvorson8604 2 жыл бұрын

Mine doesn't ratchet it just stays engaged do you know what the problem may be

@bacardii95 Жыл бұрын

hey, take it apart and see if there are any problems inside. mabe it need some new grease.

@gilbertocastillo7685 Жыл бұрын

Es justamente el que tienen ahí se me quebraron los balines y no sé cómo van ni en dónde comprar los balines

@pacheco464 2 жыл бұрын

Good?

@bacardii95 2 жыл бұрын

yes, I think it's a good machine, these are used hard.

@danieldoherty8009 2 жыл бұрын

Was that a tracker chip inside the gearbox?

@bacardii95 2 жыл бұрын

I'm a little unsure what that chip is, but it clearly has nothing to do with the machine works or not.

@danieldoherty8009 2 жыл бұрын

@@bacardii95 hi I opened mine to service it after getting it second hand and it didn't have it, I reckon its the Bluetooth tracker .

@bacardii95 2 жыл бұрын

@@danieldoherty8009 I think the bluetooth/ One key tracker chip sits over the battery.

@Jultsu Жыл бұрын

That is the "integrated blow counting sensor" which I also was not aware of when i opened up my 3/4" impact gun and I tore the cables clean off just like he did on the video. I did solder them back though.

@kacper5521 10 ай бұрын

@Jultsu I know this is late but do u know where the wires went as I just did the same thing