Mind Blowing New Tool

Learn how to indicate tools in the Tornos Multiswiss 8x26 the easy way, without a traditional indicator, with this revolutionary tool! Mowidec-TT
For more info on Tornos: bit.ly/3MDcqLh
0:00 Tornos Multiswiss 8x26
0:26 Donnie explains centering base block
01:14 Brief explanation of installing alignment jig on base plate
01:55 Shower under construction
02:24 Re-installing base block into machine
02:54 Installing Alignment jig to base
03:01 Join TITANS Discord!
03:29 Preparing to index station 1
04:05 Installing the Mowidec
05:45 How to get centered
06:22 Fine tuning
07:35 Further adjusting the y-axis
08:27 Tightening down the base
09:48 Pulling Mowidec back out of machine
10:25 Outro
Join this channel to get access to perks:
/ @titansofcnc
Join our free community Discord! / discord
Help us fund FREE Education by purchasing tools seen in our videos here:
TITANSofCNCTooling.com
Create your free CNCEXPERT profile here:
rebrand.ly/TiCNCEx
FREE CNC Machining Academy:
rebrand.ly/TiAcademy
FREE Aerospace Academy:
rebrand.ly/TiAero
FREE Grinding Academy:
rebrand.ly/TiGRIND
Subscribe for daily content and expert knowledge: rebrand.ly/SUBTITANS
___
___
Follow us on Instagram:
rebrand.ly/TiINSTA
Like us on Facebook:
rebrand.ly/TiFACEBOOK
Join the conversation on our Facebook Group:
rebrand.ly/TiFBGroup
Connect with us on LinkedIn:
rebrand.ly/TiLINKEDIN
___
___
THANK YOU to our Partners who make this content possible:
Kennametal - rebrand.ly/TiKennametal
Heller: us.heller.biz/titansofcnc/
DN Solutions - www.titansfordn.com/machines
United Grinding - hubs.ly/Q013zHpC0
Mastercam - rebrand.ly/MastercamEDUTiYT
Tornos - bit.ly/3MDcqLh
Blaser Swisslube - rebrand.ly/TiBlaser
Solidworks - rebrand.ly/TiSLDWRKS20
Trumpf - rebrand.ly/TiTRUMPF2022
Markforged - bit.ly/Titans_Markforged
Tyrolit - rebrand.ly/TiTYROLIT
Mitutoyo - rebrand.ly/TiMitutoyo
Haimer - rebrand.ly/TiHAIMER
Schunk - rebrand.ly/TiSchunk
Kaeser Compressors - us.kaeser.com/titan
#CNC #Machining #Machinist

[@boldlyspokennoah307]

Fully support non sponsored videos on tooling or any information in general that could help others

[@hughe29]

I have no access, or desire for access, to this type of machine but now I know how to centre it!

[@BuKo3007]

We are using this Tool for a long time now in our Company. But for us it is vital because we are using Drills and Mills often under or around an millimeter.

[@jegergladformad86]

Just asking. You mean a micron right? Where I work if anything is off by a whole millimeter, somebody is getting fired. A micron is a 1/1000 of a mm.

[@ernahubbard2062]

@@jegergladformad86 i assume BuKo3007 means the drill/mill dia is under or around 1 mm.

[@BuKo3007]

Yes the Tools we are using are often under an millimeter ;) It is pretty common when you are producing dental implants and abutments ect. If our Tools are out of Center they will simply break especially when you are turning and milling titanium and the other titanium alloys that are used for this application.

[@jegergladformad86]

@@BuKo3007 ha ha of course I’m soo stupid for not getting that immediately sorry

[@jeremymatthies726]

🙈........ Donnie, nice job and you didn't even get yourself in a mess again LOL. Always great seeing these different types of tools that help make things easier. Knowing me, I probably would have OCD'd that to pin point center if I was in this kind of job.

[@KalebJJaLLDay]

You are such a genius my little brother!! I love your videos and how fucking real you are!!!

[@bryantburns3664]

Your the best

[@suvajit_Dutta]

I can remember the shiney disco ball just like it was yesterday that was beautiful🤩

[@rubezahlmountainworks7974]

That exact "impact tool" sound byte should be used whenever possible.

[@donniehinske]

Yea I am seeing that as a MUST in my videos as well

[@jylmachineshopvb]

Great explanation!

[@reimondadam5297]

It's soo good to see clean machines 😀

[@suicidesquadie7990]

if your machine isn't clean, then clean it.

[@GBWM_CNC]

Loved that pneumatic allen screwdriver

[@AntalopeAUT]

Neat using a hall sensor for that if I saw and interpreted that correct . Nifty solution :)

[@splained5398]

It is a non contact displacement probe. (Eddy current probe) similar to probes used to monitor shaft vibration in industrial equipment.

[@mattiasarvidsson8522]

would love to see you make a macro that acts like sandvik optithread , for chipbreaking when threading.. I think it would also make an interesting video :)

[@pelleranogeronimo9839]

Da dadada da goes my chipping hammer! Great vid fellas!

[@benjaminzern2404]

I'm surprised that Tornos doesn't have a modifiable fixed Y position separate of the tool height offsets...this is stuff that I have to deal with on my cam-driven SAS16.6 machines.

[@Kardos55]

Awesome!

[@donniehinske]

Thank you Karlo!

[@sebasjayy]

Lmfao 😂😂 he said give me the tire change noise , editor I got you lol his sound 💀💀😂😂 I’m weak Good stuff tho i miss setting up a CITIZEN Swiss the small SR 20s too on the starz

[@Michael-nu1py]

Man that does seem very easy

[@nico8953]

Nice!

[@jesseservice7828]

Muito bom ! Perfeito.

[@kurtnelle]

Lol. Man that editor did you dirty.

[@calebasberry6613]

Sick

[@Tankliker]

Probably one of the most expensive reviews you can find on YT lol

[@RichFife]

Love these fawking videos! I like it more now that I know you guys have a weight room at your place of work. Jealous. Where I work, we have bikes and treadmills. 😔

[@j.d.7208]

Titan really is next a proud American patriot

[@larryblount3358]

No torque wrench on the 11 bolts?

[@jcruz7611]

Cool

[@cgcamry2010]

Running and sliding fits affect your pin placement. It slid in fairly easily and looked to be about 1.0". So, the pin is likely .001"-.002" smaller than the hole. So the "1 or 2 micron" is not quite right.

[@GhulamHussainEngineeringWorks]

🎉🎉🎉🎉🎉 nice cnc35x B❤️❤️M

[@mohhus98]

cool

[@MeDieValUKRAINE]

Now You should write a macro for doing all by itself ;)

[@suicidesquadie7990]

Automatic tool setters exist. Bet if you dig into how they work, its just a macro.

[@superkwabbes]

you missed a "right here" on 4:07 ;)

[@Petertje94]

great video! Love that you measured in metric haha.

[@Adam-gn4oo]

Missed a RIGHT HERE COUNT at 4:09

[@DT-yt2zh]

Hmmm.... bolt torque affects alignment. Need to be consistent on that torque for most accurate alignment of surfaces.

[@WaytARBOUJ]

Can a job be found for me? I have a degree in general turning

[@chrism4008]

You have to find your job, try creating one from scratch

[@cubedude76]

How does this sensor work?

[@toolnet024]

It’s a non contact sensor needs to be within 2 mm from the tool/ bar stock.

[@D-TRIL]

😎

[@balooc2]

what is a micron? is it like a hundreth millimeter?

[@zackstooksbury995]

A micron is a thousandth of a millimeter or about 40 millionth of an inch in imperial, a better perspective is a human hair is about 70 microns.

[@frankfarian651]

1 thousandth

[@mrechbreger]

0.001mm is one micron.

[@sirvince7853]

Anytime you're on the shop floor, safety glasses are mandatory. Anything less and you will poke your eye out

[@YerBrwnDogAteMyRabit]

I'm CERTAIN I saw a Daisy Red Rider 2000 shot action repeater rifle in the background too!

[@BPond7]

Better to have them and not need them, than to need them and not have them!

[@YerBrwnDogAteMyRabit]

@@BPond7 I agree. I carry a BB gun everywhere I go..

[@BPond7]

@@YerBrwnDogAteMyRabit 🤣

[@suicidesquadie7990]

Asking for a friend, what if you almost poke your eye out with safety glasses?

[@TylerBrigham]

Why not have locating pins?

[@Thefreakyfreek]

Works best if the same plate goes to the same station

[@donniehinske]

That is a Good question and if I had to guess it would make it so the tool holder builder would have to make these blocks perfect... forever. Aligning the tool at least gives us control and we only have to do it once. Also tools wear out and if you pin them you cant really do a whole lot to fix them other then modify them and at that point we are back where we started.

[@donniehinske]

Also if you crash the machine and bend that pin it can be really awful to fix. A lot of turret lathes I worked on we pulled pins out to avoid that issue

[@Thefreakyfreek]

@@donniehinske that gives me an idea to use pins that stick out were the tool needs to go so you have to pull them out to inser a tool but the turret is already located

[@MilkyWay-oz5ct]

Can i make a gundam with this machine?

[@chrism4008]

Only your own creativity can stop you, or the feds i guess

[@easyBob100]

If I can't show a 1.5mm setscrew who's the boss, then what's the point?

[@lily3143]

How much does this whole machine cost?

[@mattiasarvidsson8522]

yes

[@lily3143]

@@mattiasarvidsson8522 I want to buy one for my little brother on christmas

[@mattiasarvidsson8522]

@@lily3143 I assume its at least a million dollar in the most basic configuration :)

[@kristofferhjalmarsson2607]

We bought one for 1,5 million euro.

[@maka7541]

is this the son of tucker carlson? 😁

[@ADX-Adnan]

Sir l am Cnc 3 axies machinist I want to work with you

[@bryantburns3664]

Get up off that couch n do something bout it then

[@jaqhass]

I like the argument about always using eye protection. If the smartest people in the world idiot prove themselves, why should we not?

[@sparten1581991]

pls plug in the usb in the screen for power .... -.-

[@sparten1581991]

I watched it to the end .... you still have a lot to learn ^^

[@mrechbreger]

how much does this cost? good idea, guess I could make that for 200$ (including panasonic sensors). considering that they will probably sell it for 1000-2000$? Also since it's made in switzerland

[@krustiiik]

Im sorry... Why my shop doesn't have gym?!

[@aggonzalezdc]

This is what, like a $10M machine? So I only need to mortgage like 15 more houses and I can get one

[@topiuusi-seppa5277]

Incredibly unrelated, but on the topic personal protection equipment, I strongly recommend using proper gloves BEFORE they become necessary. I didn't and it took 4 freaking years of doctors appointments and several prescription grade creams and meds to stop my hands from bubbling and leaking who knows what. It's unbelievable how machine shops manage to find new ways to ruin you even after you think you know everything 😄

[@dianagarza2780]

Sorry mom... 🤣🤣🤣🤣🤣🤣🤣🤣

[@user-ni8lb2vr5t]

You said the difference is 0.0175 microns. The difference of -0.010 and 0.025 is 0.015 not 0.0175. Or is there something else you used to get 0.0175? To find the center you add the -0.010 to 0.025 = 0.015 divide by 2 = 0.0075

[@williammartin9751]

The difference is 0.035. 0.0175 is half that difference. That’s what he should’ve said. Because you’re trying to split the difference and center the tool

[@user-ni8lb2vr5t]

@@williammartin9751 it's wrong you add both numbers together and then divide by 2 and it should of zeroed at +0.0075

[@user-ni8lb2vr5t]

He has to move +0.0075 microns to zero it, and when he zeros it it will be 0.0175 microns away from the sensor in positive y and 0.0175 microns negative y.

[@frejdroid]

Your method only works if both numbers are in minus or plus, not if one is in minus and one in plus.

[@Zuuby]

You are finding the sum by adding the positions instead of finding the difference by figuring out how far each is from zero. What you did is finding the *center point location* between the measurements instead of finding how much change is required to reach that point. The difference is .035 since you would need to move .01 units from one side and .025 units from the other. Split this difference to figure out how much change is required to reach center from either side. The goal is the have the tool* equidistant from each side of the sensor, hence centered. So -.01 + .0175 would land on .0075 and alternatively .025 - .0175 would also land on .0075. *Edit sensor to tool.

[@ishmametyev]

It's great, but i didn't understand anything

[@prime-mate]

Now that this guy is all grown up, I wonder if he still sees dead people? Cool tool though..

[@donniehinske]

You are the first person to make that connection since someone compared me to that kid in the 6th grade! That was 23 years ago haha

[@prime-mate]

😂😂😂

[@prime-mate]

Great content, all jokes aside. You guys rock!

[@donniehinske]

@@prime-mate Well thank you sir! It's much appreciated!

[@DriveSMR]

Used lol

[@Coopdeville06]

Elon musk clone

[@ismaelrodriguez7443]

Spanish

[@aintdatsnipes177]

Huge pain to program.

[@darikmatters8866]

Stop with the microns.. we work in tenths..

[@ullrikegabler]

Just because you are used to it and it has been done forever its still better to go to SI instead of teaching the next generations random outdated crap.

[@tristansimonin1376]

Tenths is 2.54 microns so shit precision basically 😂

[@Paclanc]

Angry redneck appears. Did they also took your jobs?

[@m.a.6478]

Tenths of microns? That's some damn precise precision!

[@rasalgul6253]

What is a megmet?

[@brianmbugua4193]

discord....server