Mitsubishi 6G74 comparison, magna and Pajero, Chrysler LA 318

Рет қаралды 2,679

Күн бұрын

Пікірлер: 26

@noahmoore2907 2 жыл бұрын

Chrysler did have iron foundries in AUS and there were several AUS exclusive castings. In the states the 318 and 340 both used full floating con rods until around 1978

@unclebrentsshed4253 2 жыл бұрын

Oh nice mate , thanks for your input 👌🏽

@MM-sg6xm 5 ай бұрын

very informative! keep it up mate!

@unclebrentsshed4253 5 ай бұрын

Cheers mate, thank you

@AndyPat239 25 күн бұрын

I didn't realise the magna and pajero blocks were different😊

@unclebrentsshed4253 24 күн бұрын

Same , I was thinking of swapping the Magna engine straight in but Noooooo , it’s possible that the series 2 or generation 2 perjeros are interchangeable with Magnas , you know the old bread bin lid 3 litres?

@1magnit 8 ай бұрын

If it can rotate then it will rotate. That applies to the rings, valves and snap rings.

@unclebrentsshed4253 8 ай бұрын

Yes , someone needs to do an experiment and pull an engine down shortly after a rebuild

@1magnit 8 ай бұрын

@@unclebrentsshed4253 Been there, done that.

@horacecunningham7832 5 ай бұрын

Yes the piston rings rotate while the engine is running

@SajjadSajjad-zd5kg Ай бұрын

Thank you❤

@unclebrentsshed4253 Ай бұрын

Cheers for watching 👌🏽

@dieselgypsy1100 Ай бұрын

I really wanted to see this 6G74 go back together. Did you make a video of that? I can't find it. Very little on KZbin about this engine so I was hoping for whole rebuild video.

@unclebrentsshed4253 Ай бұрын

No mate , I threw it back together thinking no one would be interested in it lol . Iv done 25,000 kms I need to pull it back out as it’s leaking oil from the Chinesium head gaskets 😂🤦🏻‍♂️

@dixie265 Жыл бұрын

Back in late 80's I built a 318 for my VIP, the motor came from a Dodge Truck and it had floating pistons ( circlips ), steel crank and adjustable rockers ( 273 ) that crank looks like it's steel not cast?

@unclebrentsshed4253 Жыл бұрын

Thanks for your input , the Australian dodge truck engines (I believe) either Slant , Hemi or 318 were all balanced supposedly.

@darrynworthy7129 Жыл бұрын

@@unclebrentsshed4253 id like to know that too, i have a truck 360 i believe 1972 the block number comes up with, ive not looked to actualy see how its ballanced, i assumed the same as the car 360s heads are off, not pulled the rest down, as its stock pistons, but flat tops, all other 360s ive look into from above had lower compression pistons. i got hemi performance to build a 318 for my 4 speed 2.92 diff run 360 heads, 340 4 barrel intake from the 1970s, man it hauled arse. no they left the pistons down in the bore, i asked for a steel crank, double row timing chain, windage tray, ,high volume oil pump, i drove it 12 months, gear box cracked, got it welded put together, had the engine with me, and mate so called sold my charger on me while my daughter was getting cancer treatment. 318 i have the heads off, not looked into the bottom end. 31 years its sat, i wonder if they put in everything i ordered. i defanatly got the big cam, at 6000rpm in top gear the lines on the road turn into one solid line. young and stupid.