MITSUBISHI LANCER - INJEN COLD AIR INTAKE

Installation of a Injen technology cold air intake on a Mitsubishi Lancer.

[@josestechcorner]

Great Video. The camera work is amazing and it was clear to see what you were doing. I plan on installing an intake system on my 2014 Lancer GT sometime soon. Still can't decide on this Injen one or the one from K&N.

[@marcs4091]

Dam they don't make that easy! I had the 2008 Lancer GTS with the 2.0 it was alot easier. But there wasn't much you could do to make that engine faster.

[@itstroy4145]

There’s a lot you can do to make the car faster lol most evo parts fit in the base model lancers

[@CJLancerProphetAUS]

@@itstroy4145preach brother

[@nazana1010]

So every time how to need service air filter..?

[@pececvetkoski4206]

i wonder how much more HP you've get with intake and exhaust system instaled

[@B0RR4D0S0S4]

7hp

[@CJLancerProphetAUS]

kzbin.info/www/bejne/oHivf4yNibZpnsUfeature=shared

[@workingonit913]

Anyone have a link to the intake system

[@ProjectLouie]

Will this fit a 2017 Mitsubishi Lancer?

[@rafaelperez3803]

You have 17 me as well!!!!

[@couchpotatoinc]

Yup!

[@chiquicat1]

So you have to disassemble the whole bumper to clean the filter? Lol

[@justrandomcarsurbex3057]

Yes, or just remove the dirtguard (1 min job)

[@mcakoza9856]

I’m installing this on my lancer soon, but the issue I have is I have the 10mil screws for the bumper stripped off so it’s stuck there I’ll have to bypass this a certain way

[@thibyanthevakumar4924]

Does this fit a 2013 se lancer with 2.0L L4 engine?

[@yurrien8305]

Does it fit the 1.5 too??

[@CJLancerProphetAUS]

kzbin.info/www/bejne/oHivf4yNibZpnsUfeature=shared

[@duzisnuzi495]

whats the volvo battery reconditioner do?

[@derekmorrison5685]

where can I get a lift like that

[@CJLancerProphetAUS]

Will this effect going wet environments and mud / gravel type of areas?

[@pinipigcrunch]

YES, dont go over any flooded area, it will suck some water, also cover the wheelwell venting for those super heavy rain/ muddy time time there fore it doesnt clog the filter easily

[@CJLancerProphetAUS]

@@pinipigcrunch ohh, because i reckon if you just change the pad filter to a K&N style (NOT CONE OR SHORT RAM) Just the pad from the oem to the K&N one it should be similar and safer and a bit cheaper, these cars aren’t 6-8cyl built Or especially turbocharged so i think unless you don’t either tune it or turbocharged it, it won’t be as beneficial I believe

[@hilifetravel8764]

Is it a lancer es or gts?

[@Rain-zi4xj]

do i literally have to move the tranny oil cooler just to install the cold air intake???

[@AxelLopez-mx5ch]

This is what im trying to find out because thats exactly where it is

[@itstroy4145]

@@AxelLopez-mx5ch you don’t have to, this is a different style of cold air intake, it’s placed differently

[@rogerperez4635]

Link plz

[@Nova-pb3sq]

did you tune your car for this intake??

[@justrandomcarsurbex3057]

No, but I did get check engine light on fuel/air too lean so it might be a good idea

[@CJLancerProphetAUS]

@@justrandomcarsurbex3057 kzbin.info/www/bejne/oHivf4yNibZpnsUfeature=shared

[@ThatTNLancer]

@@justrandomcarsurbex3057Did you just reset the light?

[@chadcunningham4421]

This the same setup for the ralliart turbo ?

[@justrandomcarsurbex3057]

No, its a different setup

[@sirwanspeed]

Niice but how can me buy this part

[@justrandomcarsurbex3057]

Just Google injen system for mitsubishi lancer