MJX Hyper Go Rear Differential ReBuild Walkthrough

Рет қаралды 5,656

Rakish Rc

Күн бұрын

Пікірлер: 35

@gilbertopelaez1624 3 ай бұрын

Can you please do it for the front area full video like this one ? Thanks

@gilbertopelaez1624 3 ай бұрын

can you make one like that on the front side please and thank you for the video it helps me a lot!

@RakishRc 3 ай бұрын

@@gilbertopelaez1624 okay will post a video soon... although it's similar to the rera assembly.

@gilbertopelaez1624 3 ай бұрын

@@RakishRc thank you!!! I’ll be waiting ❤️❤️❤️

@anthonylim5120 17 күн бұрын

Didn't know the earlier models came woth Philips screws. Mine are all hex.

@RakishRc 15 күн бұрын

@@anthonylim5120 yes the new version are shipped with hex screws.

@patrioticyank4940 6 ай бұрын

Thank you sir very helpful video cause im getting this same truggy they say 500k diff oil on the front and rear really makes a big improvement on this particular model.✌️🇺🇸🔥

@brandjayfab 5 ай бұрын

Who says that? That's really thick, probably won't turn after adding that. I'm running 30k and I think it's too thick

@Ayushjeemains 3 ай бұрын

What do you think about 15k @@brandjayfab

@Boogie_the_cat Ай бұрын

@@brandjayfabyeah, 500k is insane in a truck this size. I'd go 15 in front 20 in rear.

@philiptexter1789 6 ай бұрын

This is going to be a pain in the ass

@RakishRc 6 ай бұрын

Removing the shock tower to separate the top diff cover screws is the most annoying part

@philiptexter1789 6 ай бұрын

True that. Im litterally going to get arthritus conquering this one..how long will this diff remain in the bag

@MrSjirafje 6 ай бұрын

Thanks for the guide. What ESC are you using? And does it have less delay than the stock ESC?

@SAMEERBHASKAR-y1t 2 ай бұрын

35A BRUSHLESS ESC or (COULD GO FOR 60A ALSO)

@PatrickFaulkner-pm8ci 5 ай бұрын

My top brace screws are so tight its like the poured a bottle of loc tite in each end. I have no idea how ill get this thing apart 😢 such a shame because it runs fantastic. Just got it a few hours ago and what a let down when i go-to take it apart.

@feverexplosion1968 4 ай бұрын

What size are the wheel bearings? Trying to find upgrades

@t3floz 4 ай бұрын

Thinking of buying this since my e revo 1/16 breaks alot and inhyste to work on my cars. Ive heard this car is very hard to work and i want to know tour opinion on it since it makes me hesitate to buy it :/

@RakishRc 4 ай бұрын

It's tough and durable but working on it is tedious...the screws in particular are a bit irritating to remove on the shock tower for center brace. But it's fun to drive for sure

@t3floz 4 ай бұрын

@@RakishRcoh okay thanks! I’ve heard about esc problems. Do you think my e revo 1/16 esc would fit? I think it’s about 1cm longer than the mjx esc and a bit higher but I’m not sure

@RakishRc 4 ай бұрын

@@t3floz it could fit..but the stock esc is fine...test it and decide if you need to change else use it. I am using the stock esc for now again

@Boogie_the_cat Ай бұрын

Good, but you left out the step where you need to use a flamethrower to heat up all the LocTite packed into the center brace screws. Seriously, they flood that area with superglue or something and though the screw head is large, it'll strip anyway. This is only half a joke, because if those heads strip, you're gonna have a bad time. Mine had about 3 gallons of some adhesive in it.

@Ayushjeemains 3 ай бұрын

Bro how did you got that silicon oil in 850 i am getting it for 16$ + i need to pay jn dollars so extra charges. Please tell me how did you order in 850

@gilbertopelaez1624 3 ай бұрын

Question: is the metal upgrade a good thing to get for the hyper go h14bm?

@Boogie_the_cat Ай бұрын

What metal upgrade are you talking about ? If you mean metal control arms (A-arms) then no, they're a bad idea. Metal arms will cause damage to your diff housing in a crash. You need to be specific, there's more than 1 metal upgrade so I have no idea what you're asking .