How To Replace any Smartphone USB Charging Port Without Heat Gun properly

[@revolruf]

Dude! Clean your soldering iron tip!!!! Get a sponge slightly damp and swipe the tip on it, it's not hard. A clean tip and a bit of fresh solder on it when you are done keeps it like new for a long time.

[@CatPBWater]

At 3:35ish, it looks like the electronics above the port get damaged. This method got the job done but not without consequence.

[@YNFERNUS666]

He visto malas ejecuciones de trabajos,hasta yo he hecho desastres...pero éste chaval me supera,un desastre por donde lo mires.

[@global_fusion_infomatics]

I'm already using same method without any loss good result... Better than smd work.. Use high watt soldering iron

[@MmanzilsTech]

Great 👍

[@joemarfrias1996]

Your idea is very useful for beginners thank you for sharing your tactical....

[@MmanzilsTech]

Thank You Bro

[@jimcruise9632]

I need this idea👌👌👌

[@AntiDoctor-cx2jd]

an actual text description of what's happening would go a long way

[@munindradas621]

Sir,jo cycle ki rechargeable headlight ate hen uski charging port ukhar jaye uha par naya charging port laga sakte hen ?

[@rodrigogregorio2877]

This idea is useful without hot air, I used the same technique before, but if you have hot air much better..

[@СергейПерттунен]

Для тех, кто "в танке". Это способ заменить разъём на случай, если вышел из строя фен или его нет под рукой, а замена ну просто таки горит. От себя: Гораздо проще будет снять, если иметь в хозяйстве сплав розе. Если разбавить припой на всех дорожках и ножках сплавом розе - то не нужно будет даже заливать припоем весь разъём - достаточно будет немного погреть, измазав флюсом

[@DmitryMaster]

Для тех, кто "вылез из танка": если сломался фен, нет сплава Розе, кончился флюс, отключили свет... Может ну его нафиг, заниматься ремонтом? Я 30 лет паяю, а фен живой, да и что это за горящий случай?

[@yotagoogleplay894]

​@@DmitryMaster ну какой тогда ремотник если нет сплава розе. Если есть паяльник и обязан быть и сплав розе!

[@DmitryMaster]

@@yotagoogleplay894 так-то логично, но ремонтником сейчас называет себя каждый второй, заменивший сгоревший в лампочке светодиод фольгой.

[@RingZero]

Bhai saab! great job. Keep that solder iron clean for a quality work, after all you're demonstrating your work on KZbin.

[@MmanzilsTech]

I will try my best

[@မောင်မောင်မမ]

It's working for my phone.Thank U so much.I have no idea for that because I have no hot gun. AWESOME Sir

[@balduinlefterov5927]

Use low melt solderpaste 138 C, or low melting point solder wire. It's easy, fast, cheap and professional.

[@r.k6270]

sir, may i know the flux name for desoldering the " IC " in the boat sound bar 2050

[@abidaliyousafzai3123]

Extraordinary,, very helpful

[@gotindrachenhart]

Ok, its called a soldering iron. Also, olease look up a video about how to properly maintain the tip. Soldering irons must be "tinned" in order to work well. It makes soldering much easier! Id suggest looking up some videos in this because it really does make a big difference. Then, use a small damp sponge or wet hand towel or rag to rub the tip against to clean it between soldering steps, this keeps the gunk from building up and also removes the oxidization layer. Thus all will also extend the life if the tip by years. Be careful of adjacent components. You niked the surface mounts abouve this charge port. Easy to brick the pcb this way.

[@Fishbone4u]

Agreed! Soldering iron tip looks terrible. Sloppy and lazy IMO.

[@gotindrachenhart]

@@Fishbone4u basic stuff, right?

[@jaredbengco4708]

What's that copper or bronze strip that you used for removing lead? Thanks man.

[@Tompzu592]

desoldering wick

[@mallowricyano937]

or strip a coaxial cable

[@larrymyers5989]

Desoldering wick. I remember from high school!

[@canoris267]

Hello I have a question. Will the charging connector from Samsung S10 ,S10e,S20 on S20 Fe? Or do such models have identical connectors?

[@j.caspersoundcatalyst2428]

Pretty sure they are all the same as with phones. If they are a USB micro then any USB micro will be the same process. As with usbc, etc.

[@TechnicalZafarShaikhOfficial]

Good 👍 work but microphone 99% dead hoga

[@christophertadeo6120]

Rule of thumb, The less lead or paste u use to get the job done, the better the result would be... 😳👍

[@bigpaul009]

Which is the best solder wick to use, I bought some but it doesn't get out of the holes to put the new one in, TIA.

[@TYPICALGHOSTSNIPER]

Solder wick is all same it's just copper wire.

[@Gujjar-k1y]

​@@TYPICALGHOSTSNIPER No some high quality and some low thick and thin 😊

[@Gujjar-k1y]

​@@TYPICALGHOSTSNIPER No some high quality and some low thick and thin 😊

[@Gujjar-k1y]

Mechanic wick best 😊

[@preston963]

You are right because there either laptops or mobile phones but a little dose of low melt falls out all good been a tech 40yrs

[@kadirkaraca8711]

bad work , microphone is dead bro

[@danielcano7492]

Do why?

[@danielcano7492]

The flux is not in contact with the microphone

[@workingonthatphone]

Who tell you that the microphone is dead did you try it ?

[@OnePunchHeizou]

depends on what solder he used, if low temp solder then i guess it should be fine otherwise mic isn't the only component getting damaged.

[@Jeetutech6]

Microphone dead by overheat

[@dangalf84]

How do you open the phone case to access the internals without a heat gun though?

[@-yfm-]

I have put the phone into a plastic bag and then put it all into very hot water before. Risky though.

[@theosexpertdaymon2774]

I've used a lighter (candle works too) before but you have to be damn careful. Trick is to keep it a fair distance (I think I had the tip of the flame like 5 inches away the last time I did it) away and heat it slowly all the while not burning yourself and dropping the phone or melting the phone. Not recommended if you're not very adept with fire and/or have a high risk tolerance.

[@gadid9114]

Use a hair dryer

[@j.caspersoundcatalyst2428]

You cannot

[@j.caspersoundcatalyst2428]

Oh, I'm sorry, yes a hair dryer on high at longer intervals

[@clod_23]

What liquid are you using to clean with the cotton swab?

[@danielgonzalez2582]

isopropyl alcohol (propan-2-ol), it's a good cleaner and evaporates fast and doesn't contain any water, unlike ethanol (ethilic alcohol)

[@j.caspersoundcatalyst2428]

I believe it's flux paste. It cleans everything off very well and helps with the adhering process of the fresh solder.

[@j.caspersoundcatalyst2428]

Ah, I stand corrected and now enlightened, thank you Mr. Gonzales2582, much appreciated.

[@youtubshortfun]

By that much soldering wire you used... You can buy hot gun

[@lungisamayekiso736]

Nice work especially when you put it back manual

[@evansoloruntobi4373]

What's that thing you are using to clear and opens the holes

[@pratikpandey7296]

desolder wire

[@j.caspersoundcatalyst2428]

Soldering wick

[@j.caspersoundcatalyst2428]

And desoldering wire

[@obinnakingsley8875]

❤❤❤❤❤❤,EXCELLENT WORK BOSS

[@dhruvrai-pn4zr]

hello guys, i have a hp spectre laptop but the problem with it its not charging the usb c port is very lose, so i called the call centre they said they should change the whole motherboard because it is directly connected, so i was searching for a usb module so that i can solder it but i have a doubt that can we use any usb module or there should specific ones? if there is any specific ones please let me know

[@stevemorrisby6705]

Flood soldering. That's what Motorola recommended on the 80s 2 way radios for removing hybrid circuits. There's nothing new there Your soldering iron should have a larger tip, but hey ho it works.

[@CreatorStudio-c4m]

Pls what is the name of that thing you are using to clean the led after removing

[@j.caspersoundcatalyst2428]

That's a soldering wick. If you don't have one you can strip apart an old coax cable (for like old cable tv) and you will find the same exact cable wire within. Make wicks from it.

[@jerryboy5876]

What is that copper strip called that you used after you took the USB port out?

[@abdulrafy2087]

Soldering vick

[@iloveACID]

Wick

[@j.caspersoundcatalyst2428]

Or strip a coax cable it's the same

[@johnorji556]

what's the name of the brown stuff in cleaning the panel board

[@fugeeohu9357]

I've been trying to replace chargin ports on LG Aristo 2 I have a heat gun and soldering iron but I don't have any low melt solder I have a flux pen if that helps I haven't tried using the flux One board I got it so messed up I can no longer see the pins I'm lost on that one Another board I did it with the heat gun at a glance it looks at least not a mess but the pins don't really seem to be connected The way I messed up the other one was trying to connect the pins A glob of solder got on there and then I had a struggle trying to remove it then I took the port back off and find that I can no longer find the pins What a mess Replacing charging ports isn't easy I think maybe I should stop trying until I get some low melt solder? I still haven't gotten the technique for this down

[@muazzambhatti1672]

you will destroy 4 or 5 charging ports but you will get the hang of the technique automatically. keep watching video tutorials and try to apply them as well

[@spiritlight4440]

Any recommendations for a microscope?

[@benjaminkoomson7005]

What is that long brown thing you used to clear the led left off the board ?

[@maximumeffort5865]

Solder wig its some coper wire

[@starryeyed132]

Solder wick

[@sachinazad7271]

bro. trick toh theek hai, but mic 10000% not working

[@izonehyderabad320]

Soldering rod witch company did you used

[@MmanzilsTech]

Quick

[@j.caspersoundcatalyst2428]

Rosin core

[@mervinmorales288]

Hermano cómprate una estación de soldadura

[@firdousahmad5648]

How much watt soldering iron you use it?

[@MmanzilsTech]

80watt

[@revolruf]

80 watt is good but not the cheap ones on ebay. I've purchased 3 of them. 2 never got hot enough 1 never got hot at all. I know it's not going to be something most people would want to spend too much money on but if you use it more frequently just get a Weller. They always work.

[@firdousahmad5648]

I purchased lot of 80 watt soldering irons but all not working well after i use 12 v soldering pen and computer SMPS power supply and give 16v to 12v soldering pen now it works fine

[@ВячеславЛевченко-ь7н]

Если нет фена, так проще отпаять разъём?

[@DaniJackk]

is it led u put on it?

[@sangtearalte6969]

Type c working well??

[@tellnseeartificialjewelry2971]

Bhai Link be dia kro na Ya Ports ya sockets kahan say Buy krne hain

[@pem7195]

Muy buen video

[@Krystalmyth]

Sometimes the problem. with a charging port is the small board or ribbon it's attached to and this would be pointless.

[@defaultuser0856]

1. Very inefficient 2. High probability that other components were damaged 3. Takes a lot of time

[@meranplus]

To desolder just use low melt solder

[@eng.tkmelectr6598]

Wait I thought the leads should be pressed on the nickel blade and not one on the nickel blade and the other one on the battery as I can see you doing or my eyes are lying to me 🤔🤔🤔🤔

[@vgtech4716]

Nice tech💓💝💕❤️

[@Huzayfah_Osman]

Thanks bro✅💚

[@-iIIiiiiiIiiiiIIIiiIi-]

I feel like I'm being gaslit.

[@bhoot1702]

No. But you have to be careful with this method and try not to damage neighbouring components. Just use kapton tape to cover components like mic and other ics and components And to be as quick as possible, making sure not to overheat Main thing is using low melting solder while removing the connector

[@WEVLTHX]

Title : Replace charging port without heat gun. Video : Process to use heat gun. Mind-blowing...

[@crystalmaltby3202]

😂

[@bdafonefixguy]

i missed that. i didnt see heat gun used (???)

[@den0matic]

???

[@M.E63]

This wouldn’t work I guess on the Samsung Type C in the thumbnail

[@abidaliyousafzai3123]

Very very excellent work sir

[@etechbyfasal629]

👍 good trick 👌

[@ramadhananakboy2198]

Maaf bang itu tapi ngerusakk komponen yang kecil gak bang, soalnyakan kepanasann

[@SerenoOunce]

A basic reflow station goes for $50 now. If your doing this type of repair you have no excuse not to use one anymore.

[@marinenav8]

What Liquit for cleaning?

[@j.caspersoundcatalyst2428]

Isopropyl alcohol

[@pclankatechnologies7764]

Super thx... 🇱🇰

[@mangeshpadviVideo9292]

🎉🎉🎉🎉🎉🎉very nice

[@cre0308]

Please tell me wick name and solder name 🙏

[@j.caspersoundcatalyst2428]

Soldering wick and rosin core solder

[@thekontuli2828]

"It does not matter whether the cat is black or white; as long as it can catch mice" ~ N. Mandela

[@7207691302]

Next level sir👌

[@MmanzilsTech]

Thank you sir

[@durgarajumalladi50]

Nice 👍👍👍

[@koseinwin8418]

Thanks 👍

[@MmanzilsTech]

Welcome 👍

[@jonybtw]

your face on the reflection😂

[@MmanzilsTech]

Hahaha

[@DmitryMaster]

Если нет фена, то нечего строить из себя ремонтника и уродовать плату. Паяльная станция 20 лет назад стоила 100 долларов, теперь фен отдельно стоит в разы дешевле.

[@VeLLaTv497]

Kali ko saf karne ke ly keya lagte hy

[@techyunboxinggaming7183]

Where do u live my redmi note 4 display connector is broken and I want to replace it

[@MmanzilsTech]

UAE Sharjah

[@fsimoris]

Wrong ! You have to protect microphone ! 🤨🤨🤨

[@ots-solutionOdisha]

I try this method but microphone damage this types of work

[@idrusandrian2965]

Nais

[@bustakipchumba-kp5xv]

You might interfere with the ic nearby broo

[@АлександрПотемин-ы3к]

Обычно в этом случае дорожки тоже отваливаются... Отличный метод, если надо отклеить дорожки от платы... ))))

[@bhoot1702]

No it won't fall if you apply heat equally on all joins and contacts

[@Varmadheeraj6]

Super

[@daulatthakur1015]

RIP those phone who are dead after doing this

[@albertodiseno1973]

Muy bueno 👍

[@profixfrp]

Nice

[@WaschyNumber1]

Good luck with your total dead and destroyed phone after backing your components, ther us a, reason why they use directed heat and most possible how low it can get.

[@matthewkenyon3011]

Where we going?

[@Daclaem]

brilliant

[@VK6TT]

Like your technique but the music puts me off

[@davidreynolds4684]

I've gotta cal bullshit on this. There is so much heat on that board and on the other components they have to have damage. He's melting what I believe was the mic and blobbing soldier across all contacts without separating them is the same thing as cutting the cord and twisting all the wires together then stuffing it in the charge port. Stevie Wonder can solder better than this

[@cellphonerepairing2111]

Good methad

[@rfermin5041]

I have problem in mind meter the usb

[@bombidaebombidae5560]

Можно феном снять окуратно с фольгой.. Не обязательно тратить тонну припоя

[@HLOEE]

Can you tell how did you do? можешь рассказать как у тебя дела?

[@bombidaebombidae5560]

@@HLOEE мои дела супер !

[@harpritsingh85]

Super duper

[@MmanzilsTech]

Thank you so much 😀

[@mervinmorales288]

Lo que pasa es que se calienta muy poquiiiiito y no le echa mucho estaño 😐🤦

[@chandrakantwaskar5901]

How many watt used soldering iron used

[@qasimbajwa123]

Nice trick

[@ahsamahi4385]

Too bad , you can use iron under board and heat gun with temperature and are speed

[@zulfiqarkhan8261]

❤

[@vaibhavjaiswal566]

mic may not work properly after this

[@thousifk7104]

Over heat can kill your pcb

[@mrshorts392]

That is painful to watch

[@chai___219]

After this work you need to change a digital mic hhhhhh

[@duke-ue5dg]

what????heat gun???? thats called soldering pencil not heat gun dzuhhh 👁👄👁

[@ArifBillahOnGoogle]

Easiest way to destroy your PCB

[@medabfilms1]

Waste of too much solder😢

[@remajapekalongan]

Poor solution