1994 Chevy Silverado K1500 headers

[@limabravo6065]

Dead soft aluminum gaskets make header life so much easier. Once their tight they never leak and you can reuse them

[@mikewiley1007]

This is the only video that I’ve seen of the alternator bracket getting cut. 🤙🏽

[@mobilemowers]

Hot rodders do it all the time. Have to trim things to make them fit. Not like a little trimming is going to make anything weaker. How guys had dented headers in cars to make them fit. Watch B is for Build or Finnegans Garage ect they do it like every other video it seems.

[@arnol1x5]

Will that effect the alternator

[@SingletonGarage]

@@mobilemowers will this affect the alternator or any thing else?

[@wolfeman6380]

Gawd dam that's a clean block

[@mobilemowers]

It's call a rebuild.

[@josearvizu4155]

What brand name of the headers?

[@CarlosTrujillo-vh5dv]

I have a 90 k1500 4x4 everyone tells me to run shorties or a mid size header..they say the long tubes interfere with the drive shaft and wont fit has anyone ran into that issue?

[@loudawg9260]

Are these long tubes? I have the same truck and I’m putting long tubes on and I have to change my oil filter and my front driveshaft is in the way of them

[@mobilemowers]

Hello. Short tubes. Long tubes basically go little under the cab. Just what I found in a yard and used.

[@morganrichardson1808]

Did you have to use shorty spark plugs or were your stock style ones fine?

[@mobilemowers]

Stock. Sorry for late responce I just do this as a hobby and for the past few years of this never made one dime from you tube. They did that 1,000 plus member bs.

[@cm6string]

Wanted to hear it

[@5809Alejandro]

How did you removed stock header from that braket that to power steering and alternator

[@mobilemowers]

I posted that a while ago so not exactly sure but those brackets comes off with removing the mouting bolts / nuts.

[@poppagrouch4781]

I have GMC Sierra SLE K1500, was told I needed a body lift if I wanted headers...

[@mobilemowers]

Makes no sence. Also the K series have a slight lift from the factory. So how are stock C series able to do it ? Not sure where you read that.

[@clintonclark9265]

Yes I like to know why why the brand headers was that right there

[@stormtrooper1811]

How did you go about the factory o2 censor or did you just take it out?

[@mobilemowers]

It came with a bung hole. You need an 02 to run a computer. People can weld bungs in too. They run like $5-$10. Some headers have the bung hole but you may need to drill out the inside hole.

[@mobilemowers]

You need an 02 for the computer to read fuel mixtures.

[@emiliotorres2802]

How many O2 sensors did your truck have?

[@stormtrooper1811]

emilio torres 88-94 should have one before the cat 95 too I believe 96-2000 depending on your body style will have one before and one after. The one before the cat matters the one after just checks if the cat is working properly.

[@emiliotorres2802]

@@stormtrooper1811 I definitely have an O2 sensor on my passenger side at the y pipe. I can't find another O2 at all. I ordered summit headers that have a bung for an O2 on the driver's side header. If I extend the O2 wire to reach the new position of the sensor should that allow the truck to continue to run properly? I also don't want to throw a code.

[@Chanchito510]

Whats so special about Dough Thorley Headers?

[@mobilemowers]

Hi, I never mentioned what brand they were nor knew / know what brand they were. Just headers I found in the junk yard.

[@alexmartinez3216]

Where did you get ?

[@mobilemowers]

The headers from the junk yard the y pipe from jegs.

[@brendanspecialk9851]

"...subscribe. I do these without any money from KZbin." Is that your end game or is it to be helpful to others doing similar things?

[@mobilemowers]

Well hoping after 3-5 years of posting to finally make a buck out of my time. I also helping lots out with these projects that took me tons of time to figure out. Not many people are doing the projects I am. Who else is building a 4.3 engine thats has some mods or messing with a restoration and upgrade on a 30 yr old K1500. While youtube makes 100% of the proceeds of my work. Sorry for late responce I just do this as a hobby and for the past few years of this never made one dime from you tube. They did that 1,000 plus member bs.