Model Predictive Control of Boost Converter

[@mineshjoshi5411]

Nicely and conceptually simulation analysis carried out. Thank you very much.

[@ahmadshaflyz4564]

finally after 2 years you uploaded a new video again, I can't wait for your next work 💥

[@nakiguler]

Soon, it will be about battery charge management

[@chandrasekaranr8269]

really enjoyed... thank you for sharing the knowledge

[@abdoumohamed2585]

OOOOhhh finaly 3 we missed u so much

[@aliimran4318]

Thank you so much for this video very insightful.

[@ineogaming6380]

any video about modular multilevel converter single phase with soc?

[@bryanmerino4932]

nice video, it really help my so much, thanks

[@boussaoudfarid8297]

Hello, thank you for this captivating course. I have a question regarding the simulation: I noticed that at the beginning of it, 28:10 there is a significant surge in current. How can we manage this current to control it effectively?

[@nakiguler]

Hello, thanks. Mainly, the current depends on the values of the system components such as capacitance and inductances. So if you change or improve a soft start for the control method it may be reduced.

[@boussaoudfarid8297]

@@nakiguler Good evening! Thank you for your response. Do you have any references on soft start? I would like to use it.

[@nakiguler]

@boussaoudfarid8297 I have no reference, but it is an easy mechanism: you can use a rate limiter for determining the reference. But it may have a small effect. Normally high currents are injected by capacitances at the beginning. If you desire an initial voltage in the capacitor it may reduce please check.

[@svijayakumareee]

​@@nakiguler Thank you

[@sandysharma-e8d]

so nice video, totally worth watching it, appreciated!

[@sandysharma-e8d]

Sir can you please tell us the circuit parameters used in this circuit ?

[@nakiguler]

@@sandysharma-e8d L=1mH, RL=0.2ohm, C=220uF, RLoad=20ohm.

[@mohammadvaavanvajri1259]

do you have this but on the buck converter? thanks

[@subhabratapal8808]

Nice video. After long time you posted it. I hope you are well, I am one of the subscriber of your channel. Your videos provide me lots knowledge and skills, thanks a lot for your teaching. Can you come up with a video of bi-directional dual active bridge dc-dc converter for charging/discharging cases??!!

[@lorenzobernasconi1470]

Great video, very well done! Can I ask which Matlab/Simulink library you downloaded to get the electronic components directly on Simulink? Personally, I use 'PLECSlib,' but it might be more cumbersome to work with...

[@ebarbie5016]

You don't need to add a cost function to limit the switching frequency. Instead, just add a "zero order hold" for all of the measured variables with time constant Ts for Fsw = 1/(2*Ts). This is the proper approach to limit the frequency.

[@nakiguler]

yes, it can be limit fsw. But if you want to adjust it, a variable is needed.

[@Aziz07-e6p]

I want to ask if Vin changes, does Vout also change? for example, if the Vin of the PV changes according to the irradiance and the temperature of the Vout Boost converter it will stabilize at the desired voltage or change according to the Vin of the PV. and one more thing I ask is that because Vin VP changes regarding filling inductor and capacitor values ​​in the boost converter, should we use which Vin value, is Vin the highest or should we take the average?

[@mariocastro7966]

Vout shouldn't change in that situation

[@shahilkumar5572]

can you please make a video on Magnetic Levitation simulation for nonlinear systems.

[@bhavyapandya4836]

What is the values of L and C for boost converter?

[@hashimali9294]

Thank you so much sir. every thing is much helpful, can you recommend any references or papers for PV inverter, converter and Shunt Active Filter designing parameters? it will be GREAT if you introduced video about Shunt Active Filter modeling, and thank you so much... i always follow your videos

[@LakshmiSatya-zh3dq]

sir, how to apply mpc to buck boost converter

[@faresfares1646]

Good work sir can you explain MPC based DC/Dc BIDIRECTIONAL mangement PV / battery.

[@AliHaider-hl7rw]

HI, can you tell me if its zero horizon or not? Also how can i increase its horizon ?

[@elysianzen]

Isn't it predictive control? Because you were not using the model: transfer function of the boost converter. I am a newbie. Correct me if I am wrong.

[@jandiesl7630]

Hello, I tried a model with the same wiring diagram and the same parameters, but the simscape components (from the domain with the blue lines) and the MATLAB function block were the same as yours. Solver settings - type: Fixed-step Solver: discrete (no continuous states) Fixed move from: 1e-5 And I always get this simulation result: Solver "FixedStepDiscrete" cannot be used to simulate block diagram 'FCS_MPC__Model01' because it contains continuous states... Could you help me set up the solver and your powergui? Thank you.

[@dvani9690]

Hey u got the output

[@aungnyanhtun5924]

I have simulated successfully. Do you still need help?

[@dvani9690]

@@aungnyanhtun5924 yes

[@ejazahmed5885]

Circuit is not working i tried many times.if possible can you send me mail the final running simulation file?

[@dvani9690]

Hey u got the output

[@anis_najwa]

How does we connect this boost converter to solar?

[@nakiguler]

you can get the reference current from MPPT algorithm. I used it in this paper: A model predictive control-based hybrid MPPT method for boost converters

[@anis_najwa]

@@nakiguler but may i know how to adjust the parameter for the mpc?

[@nakiguler]

@@anis_najwa which parameter? If you check the paper, you can see the output of the MPPT algorithm is used as the reference current.

[@anis_najwa]

@@nakiguler for mpc controller is it the same with the video?

[@anis_najwa]

i got confused because for this video we use iL but if we connect it to solar we use ipv?

[@mertboyacioglu662]

Merhaba, Sizinle nereden iletişime geçebilirim ? Eğer müsait zamanınız varsa bi kaç soru sormak istiyorum ? İyi günler, iyi çalışmalar dilerim.

[@nakiguler]

Merhaba, mail atabilirsiniz. Universite Web sayfamda mail adresim var.

[@abdou_8646]

What is the value of R load

[@nakiguler]

20ohm

[@abdoumohamed2585]

Sir i didnt got the same results

[@nakiguler]

please check the system parameters

[@dvani9690]

Did u get result

[@amjadmohammed9288]

Great job, Dr . I want contact with u urgently

[@nakiguler]

you can send email.

[@amjadmohammed9288]

@@nakiguler can u give ur email?

[@abdoumohamed2585]

@@nakiguler your mail please

[@nakiguler]

@@abdoumohamed2585 this is my official website: avesis.gazi.edu.tr/gulern/iletisim

[@abdou_8646]

​@@nakiguler doesn't working bro it seems it's fake I did all steps but not working

[@toutoumenna6871]

thank you so much tam ihtiyacım oldu zaman bu videonuzu buldum, çok beğendim kalptan teşekür ediyorum size. Bu sene benim phd de ilk senem oluyor ve MPC of hybrid electric vehicles with fuel cell üzerinde çalışyorum o yüzden eğer emailnizi alabilirsem çok memnun kalırım sakıncası yoksa tabi. Saygılar 🙏

[@ari8908]

Promo-SM