Thanks for making this video. Soon I'll be getting them from RFDesign too, especially the TXMod. It's a pity not many videos on KZbin talks bout these radio, especially the TXMOD, it's WiFi Feature, and the support for many to many connection topology which is a big plus point for me. I will buy 3. A) The TXMOD with the tiny 2db antenna will go to my TX16S (obviously). It will also stream the telemetry to my Android tablet via WiFi. B) a RF900X will go onto my MFD Mimi Crossbow antenna tracker, connected to a Yagi and also a 5db dipole. This RF900X will also supply telemetry to the AAT via wire (or Bluetooth, to be decided later). C) a RF900UX will go onto the plane. A will talk to C directly when it's near and signal is strong A will talk to C via B when A-C signal is weak. The radio make decisions rather than just mechanically take input and churn output. Setting up is also pretty straight forward for those familiar with command line and scripting on PC/Linux/Mac. I can put my AAT tripod in the middle of the field, or on the roof of a building while I hide from the sun under the shades or inside my car, while not having to worry about signal strength. In hot Malaysian weather that really helps.
@DanWA3 жыл бұрын
another tip, microsoft surface LTE tablets are great to run missionplanner through wifi to the TX but also USB (mavlink mirror) to an antenna tracker like the MFD mini crossbow. Inav also connects to mission planner with the mavlink telemetry enabled showing the craft and some data through mission planner.
@joshmellon390 Жыл бұрын
My set is out for delivery! I can't wait, I've had some real issues using clones. Decided to buy the set from 3dxr.
@JoseLPerez-gl9iq3 жыл бұрын
What about the RFDesign Module,could you make a video on how to use it with the transmitter signal and telemetry?
@DanWA3 жыл бұрын
I have been using RFD900x for a little while on 2 quads (16 inch and 7 inch) as well as a fixed wing, great and now the V2 JR bay module no longer needs a converter board for Sport for telemetry to the TX. One recommendation... get some short antenna extension cables as the antenna mounts on the board do peel off if an antenna gets stuck on the threads or takes a knock. Have had this happen and it wasn't fun.
@charlesmarseille1233 жыл бұрын
this is something I am always scared of knowing how the small connectors are only soldered and not glued or reinforced to pcb. I guess the db loss is negligeable for this radio system? cables and adapters introduce around 3db losses right?
@charlesmarseille1233 жыл бұрын
Great video once more! Just one note: Crossfire has been found to loose quite a lot of packets while running both rc and telemetry at the same time. Also, the telemetry rate of crossfire is way smaller than RFD systems, so to say you can also use crossfire is true, but much limited compared to RFD.
@jotham1233 жыл бұрын
Charles I've found out the same thing after purchasing the equipment. I'm trying to return it atm. How are you getting on with it? Support told me that basically, this is normal on their equipment to which my response is this isn't ok.
@jotham1233 жыл бұрын
Initially I had 4-15% link quality with all other packets lost. Now it's about 20-40% and in certain situations just disconnects altogether, just sitting on my desk. Is that in line with your experience?
@charlesmarseille1233 жыл бұрын
@@jotham123 Support is honest saying that. It's the marketing side that is not precise enough. It's like saying you can acro with a arducopter quad... you can, but it's definitely not made for it. Sell your crossfire stuff used, buy the rfd900 and get on with it.
@charlesmarseille1233 жыл бұрын
@@jotham123 Yes, pretty much the same here. Know that this telemetry should not be used as a principal and sole telemetry system. It's either a backup, a quadsaver or a diagnosis helper for me as of now.
@jotham1233 жыл бұрын
@@charlesmarseille123 I'm not giving up that easily, its marketed as such, and is brand new I'm going to push for a return. If I can demonstrate its not fit for purpose.. its pretty grey area regarding consumer protection laws. It doesn't sit right to just let it go as if its fine. It's not. Sounds like RFD900 system is the way to go.
@andrewjamez3 жыл бұрын
It would be great if you could cover some advanced stuff like the long awaited sbus pass through and setting fail-safe. This has been tortuous in the past. Thanks
@Painless3603 жыл бұрын
Failsafe is covered in the series.. Happy flying
@radon12213 жыл бұрын
Thanks for making this video. Telemetry is one of the things I wasn't quite sure about but I get the jist of it now. Thanks!
@NATGEOANDSTUFFPaulbrannan3 жыл бұрын
Great as always my friend.hope you are well and looking after yourself buddy.keep up the great work Lee.stay safe as always.
@BretChilcott2 жыл бұрын
Thank you for sharing our knowledge. 73, Bret C / AC0AE
@MCsCreations3 жыл бұрын
Really interesting, Lee! Thanks a lot for the video! 😃 Stay safe there with your family! 🖖😊
@beefybeef13263 жыл бұрын
Just what i was looking for - awesome as always painless. You do so much to help noobies like me!. Your videos are like drone university for me !
@dmytropashko82093 жыл бұрын
It is possible to connect it to transmitter and have an rc link with sbus. So you can use this radio instead of crossfire or R9. I think it is important addition to the telemetry functionality. Also encryption is here if you need
@Painless3603 жыл бұрын
Yes you can. Happy flying
@h2o-fpv6233 жыл бұрын
Great video thank u.
@beefybeef13263 жыл бұрын
I have heard that the cheap holybro v3 radios, 500mW, can give ranges of 20 miles with upgraded antennas and having them of the ground by 2m.... does anyone know if this is true? I dont want to go buy antennas that wont work and waste alot of time!....
@somalia11422 жыл бұрын
New subscribe from Somalia
@csabafarkas67383 жыл бұрын
Great video! Where can i find any guide to Crossfire - Mavlink - Pixhawk setup?
@mingijeong39563 жыл бұрын
Great video. I have a question. Telem pixhawk cable also gives 5V from Pixhawk if I know correctly. Doesn't it confilict with the separate power 5V BEC? Also, most importantly, can I know where to buy that crade? I am very interested in purchasing it.
@antrikshrajawat3 жыл бұрын
RFD is a great telemetry in terms of range and communication but the antenna on ground module are so heavy and if you drop it then pcb will break I don't like it's fragile design of the pcb and unprotected components.
@fronteirafpv84933 жыл бұрын
Great video as always! do you think its risky to use a 915mhz telemtry radio with a frsky r9m for rc? does it interfere?
@JorgeJimenez20203 жыл бұрын
I've got the TXMOD v2 and I'm trying to use it with an air unit to get RC link and telemetry through just these radios, my TX16S running YAAPU telemetry and a ground station laptop. I'm having trouble getting it to work, please consider making a video to cover this. Thanks!
@JoseLPerez-gl9iq3 жыл бұрын
Did you resolve it?
@charlesirons18923 жыл бұрын
Good stuff! , can you do a video on the new mission planner app for Android using telemetry radios? I haven't been able to get any mission planner app to connect to pixhawk since the Tower app went away.
@Painless3603 жыл бұрын
I will when it is final. Great to see MP coming to Android..
@asadkhan-mq8ro Жыл бұрын
Hy! I am also using these RFD868x-EU modules. With one pair everything was working fine as you have shown in the video but with 2 pairs that are point to point communicating with eachother. I face alot of txerror. As in EU the frequencies are fixed , so can't change the frequencies and this is casuing interference. Have you faced the same issue?
@balajin7107Ай бұрын
can it be used for ugv's also for transmitting and receiving the RTK correction data from a base station gps to a rover ?
@Painless360Ай бұрын
Yes, see my RTK videos... Happy flying
@rishabhkashi66243 ай бұрын
one very basic query. On the air side, tx from the pixhawk is connected to rx on the rfd unit, correct? or is straight rx-rx connection?
@Painless3603 ай бұрын
Most will be TX to RX etc. But it's one thing to swap if it doesn't work... Best of luck
@jorgeneo5603 жыл бұрын
i want to controll my plane with a joystick, its is necesary the rfd or just the cheap module would work? who i can be sure if the cheap telemtry is for me or do i need the rfd?
@parafarmaciatrer81193 жыл бұрын
Id like to know if is it possible to share frsky telemetry with my laptop using a usb cable. Thanks
@GravityLossFPV Жыл бұрын
Not simple at all with rfd txmod, edgetx and yaapu. This combination is killing me.
@Painless360 Жыл бұрын
See my specific videos on the topic. I hoek they help... Best of luck
@glouisfr3 жыл бұрын
Hi great video about telemetry. and on this topic I have a question for you if I may. I am looking for a way to have telemetry back to me ashore from my RC sailing boat. I'm looking to get Speed over ground so probably from a GPS, a tracking so I can map out my sailing on a map to then extract my boat speed on each tack or leg of the course (seeing my boat overlay on a map). if I can getting the healing angle from some sensor (not sure which) and ideally windspeed and angle to the wind. I know the last 2 would most likely require some wind indicator and speed sensor. But starting simple having the boat speed and overlay my sailing track over a map would go a long way for a first attempt. I use a spektrum dx6 and a flysky is6 - any suggestion for me to start on telemetry on a budget with the view to then keep adding to it?
@Painless3603 жыл бұрын
Telemetry radios can be got for not a lot of money and can work nicely with a small laptop/tablet running mission planner. See some of my older videos where I use those older, cheaper radios.. Best of luck!
@glouisfr3 жыл бұрын
@@Painless360 thanks will check your videos. I know Frsky used to have a fair no of sensors & gps but was wondering what is the best option - move to Frsky (knowing now they lock their code) or continue to use my flysky Tx/Rx but adding something like a pixhawk system with this kind of RF telemetry to send data back to a ground station.
@beefybeef13263 жыл бұрын
Hi Painless. I was wondering, do you have a video showing setup of the joystick for control through the drone thru telemetry transceiver from the laptop? Also, i checked out the link you posted to buy these radios, but they appear to be 900mhz.... Arnt the EU legal ones supposed to be 433mhz? Also, i was wondering... is it possible to plug in a video receiver into the laptop and what the drone camera is seeing with osd?
@Painless3603 жыл бұрын
Thanks for the idea. I may cover this in a future video.. Happy flying
@simonhall8863 жыл бұрын
Made in Australia, nice.
@JR-kk6ce3 жыл бұрын
Interesting. I wonder how it stacks up to Dragonlink 433 MHz? As I understand it, 433 MHz is legal both in the UK and the USA. So, I wonder why 433 is not used more?
@vince0863 жыл бұрын
If memory serves, you can set the 868 MHz stuff at a higher power level than 433 MHz based on UK regulations. Also I would go for higher frequency to get better data throughput (assuming range wasn't the main concern).
@JasonParham833 жыл бұрын
Just last week I purchased the full crossfire TX with the intention of using it as my control link as well as my telemetry radio. I have 2-way functionality via mavlink-2. What is the benefit of using this radio (in a 433MHz configuration) over using the crossfire for control and as my telemetry radio?
@AnasSuhaimi3 жыл бұрын
Wait, now the full Crossfire support 2 way communication thru Bluetooth? Like a laptop running MP, linked to the Crossfire via Bluetooth can not only receive Mavlink packets but also send them to the plane?
@AnasSuhaimi3 жыл бұрын
I don't think RF900X (the latest generation, 32 bit processors) have 433mhz variant. It does support many-to-many topology, kinda like mesh network... I haven't yet seen how people exploit this for practical purpose, but at least you could have relay unit on an antenna tracker... Or theoretically have one of the planes act as relay for the other planes in the flock.
@JasonParham833 жыл бұрын
@@AnasSuhaimi the many to many comment had me thinking... I wonder if a gotenna network would suffice over a dedicated telemetry radio. Hmmm. In any case, Holybro has a 500mW 433MHz telemetry radio. That's the one I was eyeballing before I got my crossfire working.
@mariobelseran3 жыл бұрын
Hi I have some trouble connecting RFD to Mission Planner, when I connect to MP it won’t connect. The setting for the COM port and BAUD rate are totally fine but it still won’t connect. Any advice fot this issue? Thx
@Painless3603 жыл бұрын
It could be a few things. I'd contact the seller for help in case it is a faulty unit as the radios should be supplied ready to go.. Best of luck
@emmanuelnavados38048 ай бұрын
hi i would like to ask if how can i multisik using rfd900ux? thank you
@Painless3608 ай бұрын
That is not something I have played with. Best of luck
@JohanvanderWerff9 ай бұрын
I have a Spektrum dx8 DSM2 - will this work on it?
@Painless3609 ай бұрын
These don't work with the RC radio. They work alongside, sending MAVLINK telemetry to a ground station... Happy flying
@airpaper23423 жыл бұрын
Hello! Tell me what kind of frame you have in the video 9:10
@alessandrogiovanardi5583 жыл бұрын
have you tried the new dronee zoon v3 for long range telemtry with a 2.4ghz radio?
@Painless3603 жыл бұрын
I've had them in here and was very impressed by them..
@amoshuxley29242 жыл бұрын
Will this radio work with one antenna? One of mine broke
@Painless3602 жыл бұрын
I wouldn't use damaged kit. Best of luck!
@bikashmahapatra3347 Жыл бұрын
Sir, can we use the RFD 900 with Arduino Uno directly? If yes kindly provide me the source.
@Painless360 Жыл бұрын
No idea. Best of luck
@germanmartinez78263 жыл бұрын
If I will use a jumper r8 for telemetry back to my radiomaster tx16s I dont need crossfire right, thats for sneding the telemetry to a laptop? Do you have a video about mavlink?
@Painless3603 жыл бұрын
What about it specifically?
@germanmartinez78263 жыл бұрын
@@Painless360 just the basics to understand it better since my goal is to display the telemetry on my radio's screen
@Painless3603 жыл бұрын
If you want the telemetry on the radio. That's easy. See my videos on that on the channel.. I've made a few.. Happy flying
@MuhammadAmir59403 жыл бұрын
Hello sir can u tell me the values of parameters in telemetry 2, as SR2 at parameters all data rates, thank you. I am stuck at getting parameters, it is going too slow to get parameters it takes 5 minutes to get one parameters, so kindly share the SR2 all parameters data rates thank you.
@Painless3603 жыл бұрын
It usually depends on the radios you're using and is in the manual for them - I'd start there.. Best of luck!
@MuhammadAmir59403 жыл бұрын
@@Painless360 sir I have hands on RFD900X long range telemetry as it is the same as the rest of the RFD900 series almost, my connections are okay but the data connection at the start of the mission planner at ardupilot at "getting parameters" it takes so much like 2-5 min for each parameter. Hopefully, you can understand what is my issue and help me, kindly also share your SR2 parameters thankyou.
@DronePlayground3 жыл бұрын
👍👀🇭🇷
@rizalaza3 жыл бұрын
Hi there, i'm having issues abaout pixhawk and telemetry rfd900, when my plane goes to auto it always stall and crash, can u give me advices
@Painless3603 жыл бұрын
It depends on why its stalling. Too steep a climb angle? Too little throttle? I'd start there..
@rizalaza3 жыл бұрын
@@Painless360would be possible for us to send the log/bin and parameter for you to kindly help to see if any obvious mistakes on the setting we have. Appreciate much in advance for your kind attention and response.