BEST Settings For Zhiyun Crane Gimbal | Momentum Productions

[@MomentumProductions1992]

**EDIT, MADE A MISTAKE IN THE VIDEO** INCREASING THE FOLLOW RATE NUMBER INCREASES THE SPEED OF THE GIMBAL'S MOTION.** **DECREASING THE NUMBER, DECREASES THE SPEED**

[@PabloRogat]

Momentum Productions hey !! How are you?? I have a problem because every time I turn off mi crane plus it loses the settings and goes back to the default settings.... how can I fix this?, thank you very much

[@247_sirazulmonir9]

Pablo Rogat try to use zhiyun assistant app

[@mxmushrooms2702]

Just fyi: The Crane 2 can follow the roll, if you install the new firmware and access the new POV mode.

[@jasonffx01]

Hi, for roll, if you use the gimbal in torch mode, you are using the roll part to turn the gimbal right? So, it does matter am I right?

[@MomentumProductions1992]

Thank you for watching! Subscribe with notifications turned on, if you want to see more content like this! :)

[@FreddieEJ]

You are the only person I watch when I need help with my gimbal! Such clear & informative videos thank you

[@MomentumProductions1992]

Wow, thanks!

[@bozire]

You explain AND demonstrate things so well. Thank you for keeping it simple- those are the best kinds of teachings in my book. Great job.

[@wsmfilmdocandeventsweston-4230]

A pro who is all over the place with the settings......clear as mud

[@MomentumProductions1992]

It's pretty straight forward...

[@FelipeCristancho]

1:05 Follow Rate 2:52 Control Rate 4:24 Smooth Degrees 5:25 Death Zone 7:26 Reverse Control

[@twistedpeachphotography6456]

You're the man! Thanks for all these videos. I'm getting so much more out of my crane 2 after watching all your tutorials.

[@alloneword154]

You deserve more subscribers. You are very genuine. I like that. ✌🏻

[@soamjena]

Can the bottom motor rotate too with control ? For example you want to film a wedding ring over head shot rotating slow Mo

[@randyreed3264]

You explained this all brilliantly, great stuff. Subbed.

[@roxanneashe4902]

Thank you for the time and info you put into your videos. Love your calm, insightful way. Keep up the great tutorials ..you make us all better video students!

[@gilean6179]

Easily the best video on this topic. Thank you for your work. Im always a bit hesitant to tinker immediately with the settings if I just got a device. I feel like I'm tinkering with the BIOS of my computer. Again, thank you for this video. Time to tinker with my settings.

[@PrimalOutdoors]

Thank you for the information. Do you know how you can access the different patterns? Jason

[@ricebare]

Excellent tuto, tu m'as permis de mieux comprendre le fonctionnement des réglages, merci!

[@lifewithmattandnikki3903]

Great vid.... well explained. I always come back here for a refresher! Today as I just got the Weebill. Thanks Josh.

[@natureview2891]

Fantastic tutorial. Thank you.

[@MattWhittingham]

thanks for all these great videos. you made the learning curve for Crane 2 so much easier

[@endaguerin630]

very clear demo thank u

[@mph.o]

This was so helpful! Thank you!

[@jeroenjeurissen7817]

Software is so bad. Adjusting my speed settings for panning and Saving it results in my gimball stopping to work.

[@jpsizzle]

I'm glad I found this video, you made it so easy to understand. Cheers mate!

[@MomentumProductions1992]

Thanks so much, man! I'm glad this video helped!

[@alirazakhan83]

As usual, you have made a fantastic tutorial.

[@MorefieldMedia]

My crane plus won’t do pov mode I have to use joystick to make it tilt is that normal?

[@BASEDinMaine]

Great demonstration. Thank you. Really simplifies all those parameters so I feel brave enough to mess around.

[@ItsTheGordons]

i wish this video was uploaded when i first got mine lol. the ACTUAL demonstrations will show people that there is NO perfect gimbal setting... It's all about which settings you're comfortable practicing with to master... if there were no calibration you'd have to just practice and adjust to gravity. Good shit though my man (edit) the only thing I will say is, if you use one of these to vlog, or primarily as a stabilizer, definitely set the pan to around 20degrees-30degrees, so your wrist isn't an issue as far as keeping yourself(vlog) or your subject in frame.

[@theurbanartist775]

Beer Drank Shawty I have a Canon t3i, how do I stop the gimbal from bouncing while I’m walking and filming?

[@MarioVisions]

Definitely explained it properly. Thanks man. Just did the setup up to my liking. Have you done one on how to use the phone with the crane? I'm having problems with it connecting to shoot moving time lapses

[@MomentumProductions1992]

I haven't done a video on that yet, but I will soon :)

[@thebigfrasini8403]

Nice video. Thanks. Is there a way to control the easing on the joystick? My joystick pan stops so abruptly.

[@oliverelmes79]

Thanks for the video. Are you able to use follow focus and also use the aperture control at the same time? I've not managed this, the best I can do is focus and record at the same time but having said that, I now, can't get the record function back!

[@cybertoys5154]

I am struggling to get smooth footage from my zhiyun crane 2 and Sony A6500, I think I have tried everything but when I pan, tilt or move in any direction, I get these tiny jitters, would appreciate your help in getting smooth shots. I filmed in 25fps 4K. it is not a vibration issue but tiny jitters almost looks like missing a frame or two.

[@thepurpletrees7031]

Have you tried turning off the Ibis?

[@cybertoys5154]

@@thepurpletrees7031 hi, thanks for replying, but i will sell it as bought an osmo 3 gimbal

[@theeditor9621]

you are awesome man! thanks for the tutorials

[@MomentumProductions1992]

Happy to help!

[@FreddieEJ]

Thanks so much for this video it's gold dust!

[@MomentumProductions1992]

No problem!

[@DTUFINOPhotography]

you shoudl make one of these for the crane 3 lab, but this works fine!

[@malcolmsnelgrovephotography]

Great tutorial as with all your others! stopped me binning the film idea Lol

[@carlosbeltrangomez3770]

Great videos, very clear info. Thanks a lot for all you share, I have really advanced a lot thanks to your videos!

[@MomentumProductions1992]

Thank you so much! :)

[@nancybabich]

Hi Josh, you use Sony.. Will Crane 2 work with Sony A7 in the object tracking mode via the app? I suppose that only Canon is supported here, can you correct me or confirm?

[@Day-tradingde]

Just got my gimbal today, your video helped a lot! Thanks!! By the way, how to you get your iPhone Screen into the video?

[@gregvannoy]

Your videos are awesome.

[@MomentumProductions1992]

Thank you so much!

[@philk7472]

Hi, Nice to watch a cristal clear tuto !

[@mariusblidar]

That's great. I like your videos. You're a good teacher. Thank you for all.

[@FlyingJackalope]

Would those slower follow rates help with running more if you needed to have a specific setting for that?

[@MomentumProductions1992]

Yes, it definitely could!

[@zuzkarory]

As somebody who is very knowledgable about the crane gimbal i wonder if you can help me out. I'm trying it on a tripod and do pans and tilts with the remote. I'm noticing that it is almost unusable though in that it constantly drifts in the pan axis for like 5-6 seconds when in anything other than locked mode. Problem is, in locked mode you can't control pan and tilt with the remote. have you had this same issue? when you have it on a tripod in anything other than locked mode does it drift? any solution to this? any way to make pan and tilt available with remote in locked mode via changing the settings in the app? thanks for you reply.

[@cristianmatei2961]

Thanks, dude! Saved my life :D

[@mattterry4140]

Any chance you know whether Crane 3 has the ability to change these parameters? I can't seem to find the same settings from this video to apply to the new one.

[@greggumz4]

Matt Terry I found it in the Zy play app. You have to connect to your phone and crane 3. The settings found under “Scene Mode” an icon on the right side of the screen once connected, looks like a tripod in front of a window. Only issue is whatever settings I last picked are not defaulted to unless I connect my phone after every time I start the gimbal, no way to save, and use my settings without connecting my phone each time.

[@Dependsonthelens]

Extremely helpful. Thank you!

[@heavytoon5150]

It's very useful. great work and Thank You

[@matthewwright6378]

I have the Crane 3 lab paired with the Sony A6500. I'm very disappointed that camera control through the Zhiyun doesn't work while recording. ALSO video transmission and camera control are screwed up in video mode, only manual mode... which is also ridiculous. Is a firmware update to be expected to fix this?

[@VideoUpskill]

Great settings and walk through, thanks

[@ThePino154]

legit result following this direction

[@ludovicriviere7777]

Good Tutorial, Thank you Very Much

[@vpgfotovideo9305]

Good Video, thanks!

[@h2ogogo1]

Hey thank you so much for the video. How did you find to balance an A7RII with the GM 24-70 1.8 on the crane 2? For me the lens seems to heavy and because of that I wasn’t able to balance it right - like the motor is doing fine when switched on. Without it just isn’t stable... any recommendations? Thank you!

[@MomentumProductions1992]

Did you remove the lens hood? Thanks so much for your support :)

[@h2ogogo1]

Momentum Productions yes removed the lens hood etc

[@MyTravelChannel-RO]

Thanks a lot for this great tutorial! You've clarified some very important stuff. I noticed that your gimbal saves parameters right away and mine asks me for a name. I have to give another name every time because it does not save over the old ones. My question is where are all those files? How do I load a previously saved file with a set of parameters or how can I delete the unusable files? I'm talking about Crane 2 with 1.73 firmware.

[@kennlw5]

Your AWSOME ‼️ I’m a new subscriber 👌🏾

[@MomentumProductions1992]

Thank you so much!

[@hernanbrito1423]

Thank you!! very helpful!! will this also work with the external thumb controller ?

[@FarshSchafer]

hi I just got the crane 2 but it doesn't come with battery charger adaptor do you have any recommendation which adaptor good with this charger thanks.

[@BablukanwarBK10]

Crane 2 tilt motor not working any solution 🥺

[@jkspinalchoice]

Hi Josh, When using the Crane 2, with the Sokani monitor (great recommendation!!) the HDMI cable provided will not allow for the mini usb to be plugged in. So I purchased an HDMI cable with a 90 degree bend. Now that I have both together, only the monitor works. The both will not work together. Any suggestions, how to correct that? Thanks! John

[@jimmythegent9190]

you can flip the cables that the crane 2 came with and plug in the L part into the crane 2 and the flat part into the camera

[@jorgeuribe6215]

hola tengo mi crane 2 en la ultima versión 1.77 y desde que lo hice los motores pierden fuerza y los modos están fallando, alguna solución? eh trato de volverlo a la anterior versión pero no la encontró

[@RomainOjabierto]

Thanks a lot for all your great videos ! About this one, I agree with the others, the Zhiyun Play app is a real nightmare ! I just can't save the gimbal settings. What a shame... Pce

[@DianaFenomen]

Thank you so much! Very helpful video)

[@lurmel7542]

Hello. Do you know if it's possible to simulate a little bit of camera shake by tweaking these settings? That it looks a little bit more natural, and less cinematic and artificial. For example that people can see in my videos that I walk around with my camera, but that it's not annoyingly shaky, just a little bit (as the G85/G9 body only with IBIS on and lense). Would be really thankful. Cheers :)

[@MomentumProductions1992]

My best guess is to limit the deadband.

[@epvideos6476]

Hey Josh! I recently purchased the Zhiyun crane and I been in a constant battle with the "Roll" When Im walking through a house (real estate videos) and round a corner into a room the gimbal rolls about 5-15 degrees and takes FOREVER to recover back to level position resulting in a worthless shot because the room is crooked, how can I fix this??

[@nikhilchhabra]

which mode to use when you are following someone(running) ? assuming the person is not going straight.

[@remigiuspasternak7044]

hi fantastic,very helpful tutorials need help i am on zhiyun crane plus After panning, the camera drifts very slowly on ,regardless of how small I set the pan axis (degree of smoothness). thx

[@MomentumProductions1992]

So sorry about that issue. Did you try the 6-step calibration?

[@remigiuspasternak7044]

yes no change it is the yaw axis which is drifting further after panning

[@robertcheung8404]

Hi, Josh, I am a new user with Canon 6d mark ii. I do have problems in setting up the Crane 2 with 6d mark ii. After balancing and restarting the Crane 2, I then turned back on the 6d mark ii to video function. However, it was all black screen with just a sketch diagram of a white cpu on the screen. Is it normal ? Is there any step I missed ? Did I need to see a check sign on Crane 2 after choosing the canon option ? Because I did not see it. How can I know it is properly connected ? Which button should I press for starting filming ?Sorry for this stupid question. Thanks for your help. RobertA new user

[@RussFedorov]

PLEASE HELP!! how do I apply the saved patterns that I created? I can save patterns but have no idea where to find them and apply them?

[@franciscokamel]

Ir a la esquina inferior izquierda,"Simbolo de un "Cardan"/Escenas/Y allí las verá.Para editarlas,sólo desplace la escena que quiera hacia la izquierda.Podrá editarla ó borrarla.Perdón,no sé hablar inglés.

[@cristianmatei2961]

@@franciscokamel Muchos gracias, amigo! :D

[@hzubovi1]

can I use an external joystick via Bluetooth to control the crane?

[@LengLynn]

yes, you can connect gimbal with ZY play or VC100 to control gimbal moving

[@Deep-Travel]

Great video. Thanks

[@FloNFC]

How you can make the camera image to apear on your phone??? tnx!!!

[@mreddieau]

Is it possible to reduce the stepping effect from this gimbal (you can see the steps of the operator in the footage)

[@MomentumProductions1992]

Check out more of my gimbal tutorials :)

[@SBKProductions]

greta video! did you make the video for walking movements yet with the gimbal?

[@MomentumProductions1992]

I have a ton of gimbal videos, so be sure to check out my playlists! Many more gimbal videos are coming soon!

[@SBKProductions]

Thank you for the reply’s best tutorial channel I’ve come across! I have one last question for a while 1.I’m shooting music videos with my crane v2 so I’m not sure if i have my settings right? Do i want them slower or normal ? And what mode will be best for videos out of the 3 modes?

[@MomentumProductions1992]

I use normal and most of the time, the Full Follow mode. Thank you so much for the kind comments :)

[@EricCheung]

Great video and advice..thanks dudee

[@stellavdb]

hello, I have a canon mk iii and the zhiyun crane 2. With the manual focus I try to use the focus wheel and it doesn´t work, it only works if I put the autofocus but in this way it also moves the focus alone. You can help me? I think than all the adjustmenst of zhiyun are ok, but i don´t know why doesn´t work. Thanks you a lot!

[@peter.karundeng8841]

can you make a new video how to connect Zhiyun crane 2 with Sony A7III ?

[@clivebrincat88]

My Crane 2 won't retain the settings set on the application after turning the crane off and switching back on (it will resort to some default settings again). Is there a fix around this? Thanks

[@peterfuchs7781]

Thanks for that video!

[@mgr5550]

I use the ZY Play app too and cant get the gimbal to finally stop at the final point. It will instantly jump back to the default home position. Example i set point A to focus on a vase and then point B to a window. The damn thing wont finish and stay at that window. It will immediately JUMP to the start position. Any help from someone here who knows how to make it stay at the last waypoint/position being set ?

[@danielionut4738]

these settings only change when you're connected to the phone?

[@ryanhaagen1396]

great tutorial

[@Kanyunyer]

Help. When I changed the motor settings to Medium or high I cannot control the joystick? I need to restart the crane to be able to control it but tje motor settings will go back to Low.

[@savetherobotsfilms4131]

Hey bud! Seen most your vids, great work! I just purchased a Crane Plus and I cannot for the life of me get the Sony Camera Control Line activated so that it recognises my Sony (A7rii). The manual says to "configure the stabiliser to suits ´Sony´in Gimbal Setting Screen, then save" but fails to mention WHERE this ´Gimbal Setting Screen´is! In past tutorials on youtube they refer to an app called Zhiyou assistant but it appears it's no longer available. From the ZY PLAY app there is no such setting. I'm 45 seconds from sending it back. =(

[@MomentumProductions1992]

Hey! So sorry about the issue. What exactly are you trying to control with the Sony camera?

[@savetherobotsfilms4131]

Hey! I just need to tell the Gimbal that I am using a SONY so that the shutter/zoom/vid rec can be operated from the gimbal... The guide doesn't specify which program/app to use, and I cannot find the Assistant App in the App Store for the life of me... Is it possible to configure through the ZY PLAY app? (I couldn't find any setting to specify manufacturer)... Thanks for your help!

[@MomentumProductions1992]

This setting is within the ZY play. Try checking out my latest video on the Smooth 4 and it should help you out in finding that setting :) kzbin.info/www/bejne/hZjXfJZnj6-ZqZI Let me know what happens! Thank you for watching too! :)

[@cyrus21731]

Hi Josh, it's Cyrus from HK. Thanks for your sharing! I also have a Crane 2, this my first gimbal. I would like to ask something about Crane 2, when I open the Crane 2 at Pan-follow mode, why I can't tilt up or down to 90 degree? Is this normal? or my setting have problem?Thank you for the suggestion! (P.S Please forgive my poor english)

[@cyrus21731]

I'm using Sony a6500 with sigma 16/f1.4 or Sony 10-18/f4

[@brunocassettari1991]

Hi, hello! I have a Crane 2 and are trying calibrate, when i save setings the gimbal stops responding, follow focus still working but the gimbal not and i have to restart. Do you now why?

[@orrickmedia7442]

hi there got the Zhiyun crane 2 , i cant for the life for me understand how to stop the servo follow focus from slipping backwards when putting against the lens , ive tried to tighen it with the screw but its still not keeping it it snug ??? any ideas

[@MomentumProductions1992]

Hey there! It may be tricky, so perhaps I should make a video on this? See if this video helps: kzbin.info/www/bejne/bZTOen16etuVhpY

[@yvette9867]

how do i fine tune the gimbal horizon line so that it is level when there is a quick release plate that is not entirely flat. The old version of the app seemed to have a "fine tune" but I don't see it in the new version.

[@MomentumProductions1992]

I will make a tutorial on this! Thank you! :)

[@remigpasternak4843]

Hi i am on Crane Plus On PF Mode after Panning Camera still drifts on Please help

[@MunteanuFilms]

Need something like this for the Weebill Lab

[@MomentumProductions1992]

Your wish is my command! Coming soon :)

[@MunteanuFilms]

Momentum Productions can’t wait. Can’t figure out where to even find the menu to change the on the weebill. Thanks Josh!

[@paulcryer]

@@MunteanuFilms For the Weebill Lab, I finally found out how to do it. You need to disconnect the gimbal then hit camera on the "connect device" screen to get the traditional screen with the settings icon for the control settings. Looking forward to Momentums thoughts on the settings though as I've set mine to suggest crane ones.

[@ScarmackProductions]

What's the point if the Crane itself resets to default every time you turn it off? Unless you plan on redoing it every single time (Yes, it only takes a few moments, but still. While working in the field, especially at a wedding, you're not going to want to keep resetting your settings. Sounds like this is a bug they need to fix).

[@darthbert]

if you change the settings via USB to your PC using the calibration software you can set the turn on defaults of these values.

[@cellar-door]

Is there any way to have the Crane keep the settings without having to open the ZY Play app all the time?

[@MarceloGori]

Not just a thumbs up but a great thanks as well!!!!!!

[@StuTuckerMusic]

quick question... in "PF" mode if I'm walking and a decide to turn my body and walk left, why does my crane two turn right?

[@99secondsTrip]

thanks man really help alot to me

[@hongyuan8538]

Great video, thank you so much.

[@MomentumProductions1992]

Thank you so much for your support

[@tobiajayi8132]

is there a dual handle system for this crane ? (like the one for crane v2,v1)

[@MomentumProductions1992]

Yes, watch this :) kzbin.info/www/bejne/r6Czf52tpNSEjs0

[@DavidBoanuh]

I was told switching on and off the crane resets to default settings. Is this true?

[@PabloRogat]

David Boanuh it is true..... and is a pain in the ass

[@martindoersch]

same at my side... thats to bad. But... so what. Now fiddling around and learn to use the defaults...

[@nightdonutstudio]

If you using computer software to change the setting. I believe it will stay.

[@MrMilanina]

Kai Liu Visual Same here, I kept connecting the crane to my app every time I started it. This way the it would load my settings, but really annoying.

[@CharlesMiner]

Where are the patterns saved? I can never find them

[@DJVayremix]

I'll follow your advice. Thanks bro

[@treffermedia9202]

does the menu controll wheel feel super ugly to touch for you guys? the cheapes plastic feel I ever had on my finger..... or are there fake versions of this one?

[@markshirley01]

Josh - do you have a link to the video Zhiyun just posted (piano in it)

[@MomentumProductions1992]

Here you go! :) kzbin.info/www/bejne/q3i7q3R6ap6LiMk

[@markshirley01]

Momentum Productions thanks Josh

[@pirukapekka]

Hi, little bit confusing is for me, do i need everytime save preset, if im saveing preset, then next time after changeing parameters app tells that you already have this preset, maybe also android app dosnt work as iphone app...

[@JJUmusic]

if you want to edit a preset, do not access the settings via the gear icon, instead you should click on the top right icon (the 3-axis gimbal icon) . Then you will see a drop down menu: scene mode, application mode, joystick. Click into scene mode, thats where you'll find all of your presets. To edit a preset, simply swipe that preset to the left, and you will see the options to edit / delete that preset. hope this helps :)

[@friedom]

This didn't work for me. I'm on the latest ZY Play app for iOS and completely unable to save any PTZ settings adjustments with the Crane Plus. No matter what I do it reverts back to default. The only ones I can choose from is Walking and Motion under scene mode. If I make any PTZ changes it doesn't take at all. I'm unable to edit the presets too.