I’m surprised you didn’t soak the pieces in Evaporust to remove the rust.
@tiredoldmechanic17918 ай бұрын
Anyone else get flashbacks from shop class as Keith was installing that chuck without a board on the ways? I recall teachers hollering at students doing that.
@ellieprice3638 ай бұрын
Those ways are hardened and if you’re careful it doesn’t hurt them. Still, a board to protect them is always good practice.
@kennethstaszak99908 ай бұрын
In my shop class we had cradles to support the chucks, handles front and rear for lifting. I made some for my lathe many years later.
@garybrenner62368 ай бұрын
B. S.!@@ellieprice363
@petemclinc8 ай бұрын
Yeah, he sometimes does things that makes me cringe...
@Labrador_Iron8 ай бұрын
if you look closely the chucks diameter is small enough that its resting on the 'Inner" ways which only the tail stock and steady rest use, neither of which will ever be in the chuck area so no real harm in regards of function of the machine just aesthetics. a lot of older Lathes I've seen are pretty beat up in this area anyways from years of little nicks and bumps.
@juliancripps15808 ай бұрын
Great to see the Tally Ho capstan base , clean and ready for a new cast cap!
@65BAJA8 ай бұрын
Pretty sure the first "job" for the lathe is machining the capstan base for it's powered conversion.
@Paul-FrancisB8 ай бұрын
Good morning Keith, that is a big boy's tool post! I think the guy who made that jib crane assumed that you would swing in from the back of the lathe rather than the front with the post being offset to the rear, then the load wouldn't want to move as much when you lift it.
@cyrilhudak45688 ай бұрын
Was going to say the same thing. Anyone else cringe when he set that chuck on the ways without wood protection?
@m9ovich7858 ай бұрын
He said the cart was too wide to fit between the lathe's...
@Paul-FrancisB8 ай бұрын
He did 😁, the chuck cradle wants a smaller cart but it sounds like he wants to build a new crane anyway
@ellieprice3638 ай бұрын
Taking that Aloris tool post apart and reassembling it was a good learning experience for me. The three start thread and matching movable cams continues to be a very valuable and useful invention by Mr. Sirola. “Aloris” is the inventor’s name spelled backwards.
@ianpendlebury95038 ай бұрын
That 3 jaw chuck is a work of art. As an amateur, I've never seen anything like it.
@edbennett82578 ай бұрын
Just a hard learned lesson, when tapping a tee nut, stop the tap just short of forming the threads all the way through. Make it so a bolt won't thread all the way through the nut to prevent forcing against the bottom of the slot accidentally.
@Sizukun18 ай бұрын
I was hoping for a bunch of parts to go into your giant vat of evaporust! I guess I never thought about it before but I didn't know tool posts had those giant screws in them like that!
@thefirstcalled8 ай бұрын
OMG! My sphincter tightened and my toes began to ache when I saw the little crane bend.... LOL!!! Thank you as always Mr. Rucker! Since retirement, my new career in watching people move metal is awesome! 😊
@ericmcrae77588 ай бұрын
Hi Keith A couple of observations I was surprised you had that chuck clonking around on the ways, why not use a plank of wood on the ways then the chuck? and I seem to remember you used to have a tank of Evaporust wouldn't that have been perfect for cleaning up the tool post.
@LanceMcGrew8 ай бұрын
Ditto - cringed when chuck banged against ways thinking get out the plywood please
@doughunt51758 ай бұрын
That crane sure looks like it was meant to lift the work from behind the machine. Which makes sense, so you don't risk smashing the controls.
@m9ovich7858 ай бұрын
He said the cart was too wide to fit between the lathe's...
@trainman28608 ай бұрын
It might help to put a piece of plywood across your ways to put the chuck on so it does not damage anything.
@bcbloc028 ай бұрын
Exciting to see that machine finally making some chips!
@jimc47318 ай бұрын
Keith, you used to use evaporust for everything, as of late you do not use it at all! Did you loose the sponsorship? JIM 🎉
@ellieprice3638 ай бұрын
I’m guessing the name- brand stuff is a little too expensive for general use when white vinegar at $2.00 gallon works just as well. After the vinegar soak the light acidic action must be neutralized and the part dried and coated with oil.
@Hoaxer518 ай бұрын
@@ellieprice363,Yea, but Keith already built a vat and had put at least a 55 gallon drum of Evaporust in it, it had a lid too so it wouldn’t evaporate. I wonder if he still has it, that Aloris tool hold and those Chuck’s would have been a perfect use for that stuff. Maybe not enough time in a day because you should probably let whatever you’re working on soak overnight for best results.
@nighttrain14508 ай бұрын
So I am going with Leo’s capstan for the next job. I saw it in the background on the floor and the top should be ready soon. What ever it is, I can’t wait to see the lathe used .👍🇬🇧
@grharr413626 күн бұрын
I see Tally Ho's windlass in the background..! The video's that you made depicting the huge amount of work required to refurbish and rebuild their windlass was phenomenal A huge undertaking and I watched them all. I was very impressed with your skill and ability to create such great work. In fact, it's how I became a fan and watch every video you post. Great job. Great work!!
@scottthomas59998 ай бұрын
That Cushman Chuck has really nice features. 👍🏻👍🏻👍🏻
@stuartm83358 ай бұрын
Keith says at 29:27 the cart is a bit too big to fit behind the lathe so i guess that is why he is picking up from the front.
@phillipyannone31958 ай бұрын
Sounds like the capstan will be making an appearance.😊
@Hoaxer518 ай бұрын
I could see it sitting in the background on a pallet so it’s probably going to happen real soon.
@scottbishop78998 ай бұрын
Should've lifted the chuck on from the other side of the lathe to have your jib crane pivoted out over the floor, if you're going to mount from this side you would need the pivot arm moved to this side of the lathe or extend the boom on the jib crane (you may have to put extra support on the mounting arm etc though).
@m9ovich7858 ай бұрын
He said the cart was too wide to fit between the lathe's...
@scottbishop78998 ай бұрын
@@m9ovich785 well that's a bugger, needs a thinner cart then lol
@markedis59028 ай бұрын
I agree with @davidt8438 Evaporust would have done a better job by removing the most rust and converting any left into a stable form. The phrase that springs to mind is “Don’t spoil the ship for a ha’porth of tar”
@Charlybob90088 ай бұрын
I think you'd benefit most with an overhead beam and trolley system designed to be able to move on a second set of two beams and trolley that will allow you to lift and move things in every direction above the lathes
@boogiewoogiebubbleboy28778 ай бұрын
If you are going to be changing the 3 and 4 jaw chucks over on a more frequent basis, I suggest you sort your crane out ASAP before one of you gets injured! It's great to see some actual machining done for a change. Thanks, Keith. 🏴⚒️
@avoirdupois18 ай бұрын
Great to see that lathe making chips! Looking forward to seeing it put to work.
@johnsherborne32458 ай бұрын
Years back as an engineering student I was shown round the Swindon railway works. Nothing there was small. They had the mother and father of a travelling crane, ran down each side of the building, spanning everything. I’ve often thought Keith would really benefit from a proper crane. Any one got one going spare ?
@petertitterton68368 ай бұрын
I also went round the Swindon Railway works. My late father-in-law was a chargehand coppersmith there. After it closed it became a designer outlet centre. Some of the old cranes and other pieces of equipment are still there.
@johnsherborne32458 ай бұрын
@@petertitterton6836 rather a sad come down for what in its prime was one of the worlds greatest engineering works.
@TheAukel8 ай бұрын
“I kind of got an idea on something I can build.” - Keith Rucker See a problem, solve a problem. Love it.
@johnwallace90028 ай бұрын
A trick we used to use at work was put the come-along on upside down then you have the ratchet down low mor convenient.
@johnsherborne32458 ай бұрын
It’s funny how obvious simple ideas can seem. Good one!
@Barnagh18 ай бұрын
Great to see it running so well after all your careful work.
@johnhughes39958 ай бұрын
Definitely need to improve the crane. Great work as always.
@tedmiles21108 ай бұрын
I remember when you brought that big lathe into your shop! It has been years; but well worth all the work you put into it! Ted Miles long time watcher
@bulletproofpepper28 ай бұрын
Your happiness is hard to contain but it’s beautiful to watch. Thanks for sharing. I know that chuck was so heavy it may have broken a piece of wood between the ways. That chuck is art.
@CothranMike8 ай бұрын
ArmoredPepperDuex the way to prevent ways damage from mounting and dismounting chucks and faceplates is to place a device, prepared well in advance, which has wooden riser blocks connected at the bottom which drops between the ways in question and supports any falls or even scratching, had an oldtimers adjustable way caddie in a shop I worked at which fit the purpose. Very handy and easy to store with the chuck cart.
@4englishlies8758 ай бұрын
Congratulations, first cut! This was very cool.
@phildegruy92958 ай бұрын
Your mention of your friend having worked for Cincinnati Milacron brought to mind we had a body shop full of Cincinnati Milacron T3's as spot welding robots back in '95. They were beasts and could rip a Suburban body off the carrier and fling it around like it was a toy. In 1990, ABB bought the robotics business of Cincinnati Milacron in the Us and the Cincinnati robots were gradually phased out for ABB robots.
@tropifiori8 ай бұрын
What a gorgeous set up. You really turned some beat up equipment into pure jewelry. Kudos Frank
@markbernier84348 ай бұрын
Really impressive to see that working. I will say I think the crane needs to be near the top of the list. What I saw you do today is a finger smasher waiting to happen.
@littleworkshopofhorrors23958 ай бұрын
I think the chucks are meant to be loaded from the back of the lathe , not the operators side, judging by the cranes pivot point. Would save the finger mangling possibility, or at least reduce it lapse of attention senior moments.
@CothranMike8 ай бұрын
@@littleworkshopofhorrors2395 As Keith said, it does not fit at present, I too would seek to accommodate a useful addition such as the jib crane and chuck cart. Trouble is... which lathe to move, or even rework the cart a bit. A lot to ponder.
@chrisstephens66738 ай бұрын
@@CothranMike the cart is fine and the crane is fine, its just that it looks like the cart should be at the rear where the crane could lift a chuck straight up and then swing Inboard.
@carlkulyk3668 ай бұрын
I admire your taste in machine tools, all top shelf kit. I think you have the best home shop on you tube.
@jsteifel8 ай бұрын
oh boy Keith, I was holding my breath when you were moving that chuck over. I was hoping you were going to put some wood in there to protect your ways. did you clean the scroll out after all that wire wheeling and scotch brite work.
@hpda448 ай бұрын
Wow it’s been a long time coming! Congratulations Keith.
@ianmoone23598 ай бұрын
Awesome work as always. Really nice to see an old lathe have new life breathed into it. Of course to restore a lathe you first have to own a lathe 😂😂👍 If I were to guess, I’d just about bet dollars to donuts that the large machining job that you have coming up is the new cast winch capstan for Leo’s Tally Ho Boat restoration that’s being cast over at Windy Hill Foundry. Can’t tell you how much I’m looking forward to this next series on that project Kieth, it combines two of my passions - boats and machining. 👍👍👍🇦🇺
@robrobitaille42358 ай бұрын
Nice job. What a beautiful lathe. And, as usual, I learned stuff. Thank you!
@masteruniverse35068 ай бұрын
Single point threading is always magic!
@andrewstoll45488 ай бұрын
It's kind of funny watching you use this large handle with the big tap when earlier I watched Curtis of CEE sweating using a 2.8mm tap hoping not to break it.
@samuraidriver4x48 ай бұрын
I rather tap a 1 inch hole then a 2.8mm one😂 Tapped plenty of m24 and m30 holes by hand but I hate the small sizes under m5.
@paulcopeland90358 ай бұрын
*Kurtis
@swarfster8 ай бұрын
I wonder if they loaded the chucks from the back of the lathe and that’s why it doesn’t swing over the front?
@truckguy66668 ай бұрын
I love how you do what is reasonably necessary without going to great lengths to repair/replace/remachine every little aspect. Its a glimpse into a real life shop where stuff needs to get done, not necessarily to make video content. One of my favorite channels for a long time now! All of the woodwork/metalwork channels are trying to outdo each other and its giving amateur/novice viewers an inaccurate depiction of the trades..
@switch24728 ай бұрын
Keith, you can wire wheel and then boil your rusty steel parts, and it will convert the red oxide rust into black oxide. Still need to rub down/wire wheel off the flaky red before and after the boiling, and you just repeat the boil-rub down-boil cycle until only black oxide is left. Then, just treat it like any other black oxide coating
@waynephillips27778 ай бұрын
It's great to see this lathe making chips.
@haydenc27428 ай бұрын
I saw a guy online that did a home DIY nickel plating on his tool holders to keep them from rusting...have you ever done a video on that? Very cool on clean up and setup of the tool post! Awesome stuff! Keep em coming!!!!
@SciPunk2158 ай бұрын
It's ALIVE !
@waynep3438 ай бұрын
Years in the making. Looks beautiful. Congrats on the first chips from that. I have seen most if not all of the videos on that rebuild.
@dcrahn8 ай бұрын
Why not use your tank of Evapo-Rust? Also (Lathe Care & Maintenance) Never lay your chucks or any tools on the Ways!
@darkwinter73958 ай бұрын
I was thinking exactly the same thing... don't grease it yet, evapo-rust it first! 😬
@johnbewick63578 ай бұрын
I guess you are going to need this lathe to machine the Tally Ho capstan, which looks like it is on the crate by the forge. Saw a preview of Clark casting a prototype capstan top which was broken in your shop when dismantling it. Cant wait to see it being machined and put back to working order.
@donmedford25638 ай бұрын
The scroll on that 3 jaw chuck is the slowest I have ever seen. One think I would love for you to show is cutting a 2 or 3 point thread like is on that tool post. I have seen lots of single point threads cut on you tube but never any thing else.
@mikes44088 ай бұрын
Thanks Keith! Nice vid. Please check your audio. Thanks
@MaverickandStuff8 ай бұрын
That is a nice chuck. You could flip the inner and outer jaws around and get what looks like 6-8in of engagement on the part. You can really get a good hold on your parts.
@PhilG9998 ай бұрын
I'm only 2 minutes in but I can tell this is going to be a good one! Can't wait to see that 612 making chips!
@floridaflywheelersantiquee75788 ай бұрын
Thanks for sharing Keith
@frankerceg43498 ай бұрын
Thank you Keith!
@davidhall17798 ай бұрын
yeay team, first chips on the monarch. its been a great project to watch.
@joelchabot51678 ай бұрын
Keith you should put plywood to protec the lathe bed of that big boy. Keep on
@alun70068 ай бұрын
It's alive, it's alive! Congrats on the big milestone - looking forward to seeing what you do with the beast. That chuck is a monster - it probably weighs more than my whole lathe!
@rexmyers9918 ай бұрын
WOW,! A very big moment. First chips on the Monarch 10 EE lathe. CONGRATULATIONS,Sir.
@ratdude7478 ай бұрын
Wrong lathe. This is a Monarch 612... his biggest lathe. Monarch 10EE is a small toolroom lathe...same company, but very different product.
@rexmyers9918 ай бұрын
@@ratdude747 Ah my bad! Sorry
@johnmolnar29578 ай бұрын
I see the Tally Ho Capstan casting fitted up in that lather for machining
@HorsleyLandy888 ай бұрын
Making chips, well done Keith.
@ddblairco8 ай бұрын
thank you Keith
@WillyBemis8 ай бұрын
Great video! Thank you Keith!
@TheLfd2138 ай бұрын
Love the sound of the rain frogs in the background. Brings back memories of the shop at my grandparents farm
@Ron-k8e7f8 ай бұрын
good job keith
@FutopiaAD8 ай бұрын
A board across the ways would be really cheap insurance while mounting that chuck. That chain looks pretty spindly
@seapy23988 ай бұрын
Naa, chain made in China will lift ANYTHING!
@robertmatel81368 ай бұрын
What happened to the huge Evaporust tank?
@wallaceknifeworkshomestead8 ай бұрын
Nice ! Would that big job have anything to do with a sailboat? 😁😁
@maureennewcomb78828 ай бұрын
That’s my bet.
@jamesnorman4158 ай бұрын
Tapping that hole made my back hurt!😊😊
@marvinschleicher55428 ай бұрын
I think you should put a board on the ways to keep from dinging them up. Chuck is heavy and wouldn’t take much to mar machine. Just thinkin
@rickswanberg49958 ай бұрын
You might want to make a chuck for the tail stock similar to the one Curtis of CEE made for his big lathe.
@davekummer65878 ай бұрын
You beet me to that. Comment. Same. Idea I Thought.
@timf69168 ай бұрын
Great job
@PixelSchnitzel8 ай бұрын
Why use the wire wheel to remove rust when you have that big tank of Evapo Rust? It would get into the places the wire wheel didn't and keep your grease from getting a bunch of rust suspended in it.
@StevenEverett78 ай бұрын
Congratulations Keith on a job well done!
@jpgsawyer8 ай бұрын
You really want to look at Evaporust. It just removes the rust and leaves the part clean. Perfect for getting into the nooks and crannies of a part like that tool post. Just so nice and just takes a bit of time. It doesn't leave anything being like other rust removers and doesn't burn you either. Just makes like so easy.
@ericmcrae77588 ай бұрын
Keith has a tank of Evaporust I really dont understand why he didnt use it unless these videos are all out of date sequence,
@lynnplestid27118 ай бұрын
Is that the capstan the back ground from windy hill?
@chrisrhodes54648 ай бұрын
So your job for this lathe is the top piece of tally ho capstan I know that windy hill founder is about ready to have it ready
@edcallahan69528 ай бұрын
Nice video I have a cushman 4 jaw combination chuck works slick probably 16 inch , you have a cushman chuck publication showing them and how to use them. Thanks for all your effort making this video ed
@richardfisher32538 ай бұрын
I noticed the Tally Ho's Capstan in the background by your forge. What is the status of that project?
@cyclebuster8 ай бұрын
My Chuck on my Walcott is a 4 jaw independent / Scroll chuck, similar design to yours. Everything I chuck in that thing goes to .0000. I am rapidly wanting to use anything but a 4 jaw.
@johncloar16928 ай бұрын
Great job Keith you have a very nice machine. As alway you do very fine work. Looking forward to see you use it in the future.
@kevinkohler51408 ай бұрын
Knowing your familiarity with evapoRust, why not use it for the toolpost?
@Arnie101018 ай бұрын
Good morning, Keith :)
@fjjunker83888 ай бұрын
A very good video. Thank you very much.
@MartsGarage8 ай бұрын
Hello Keith. I love the big Monarch, what a sweet machine. You've done a great job on it. I was also impressed by the adjustable 3 jaw. That's a pretty versatile piece. Re the crane. The addition of an intermediate arm would allow far more range and would be a neat way to do it. Of course the roller beam type of device would also work but just pointing out an alternative. I'm interested to see what you want to do on the lathe and any more mods you care to do. All the best, Mart in England.
@WreckDiver998 ай бұрын
Can't wait to see Tally-Ho's capstan up there...Are you also going to do the machining on the casting from Clarke as well?
@pinterelectric8 ай бұрын
Looks like so much fun!
@tpobrienjr8 ай бұрын
Fine looking machine
@Halinspark8 ай бұрын
Could you use the adjustment on the chuck jaws to loosen one jaw, flip something around, and tighten it back down without losing as much concentricity? Sounds great in theory, but in practice doesn't care about theory.
@stevedunford76327 ай бұрын
Am I right in thinking those jaws with the extra adjuster behind means the same jaws can be used for external and internal clamping. If so then the jaws could be opened to a point where the scroll was still engaged then use the secondary adjuster to pop the jaw out and reverse it
@6NBERLS8 ай бұрын
Most excellent.
@mudnducs8 ай бұрын
Congratulations!!!!
@petegraham14588 ай бұрын
Looking forward to seeing you put this to work!
@rgmoore8 ай бұрын
Wonder why not use that huge tank of EvpoRust you used to have. That stuff should have eliminated all the rust in all the areas for a bit of soaking.
@CraigLYoung8 ай бұрын
Thanks for sharing 😅
@linasvelavicius3308 ай бұрын
Keith, excellent job on the Lathe Restoration, looking forward to seeing you using it. If you are going to level the lathe can you move away from the machine behind it so a cart can fit and use the chuck hoist as intended?
@ronwilken52198 ай бұрын
Hi kieth, I guess a long journey finally comes to an end, sort of. If I may can I suggest a couple of side projects to make your machine a little easier and safer to use. You've already touched on the new improved jib crane so I won't go there. However your banging that heavy chunk of metal on the bed ways you spent so much time repairing made my skin crawl. Please make yourself a wooden cradle that will ride the ways at the correct, or near to, height to fit the various chucks. The Aloris tool post is a great addition. I don't know if you've seen it done but some with those types of posts have found that installing a roller thrust bearing under the top flange nut enables one to tighten the post more securely and reduces the possibility of the whole post rotating under heavy cutting loads. Since youre going to order a flange nut from McMaster Carr a suitable bearing will only add a few dollars and use less than a quarter inch of your bolt length. On the subject of the T nut in the top slide, if you cut the thread only until the tip of the tap appears the bottom thread will be incomplete, the stud will only go so far and you'll be safe from not cracking and/or jacking the top off the top slide. Getting rid of that copy attachment and replacing it as you've suggested will make a big difference. Overall, a satisfying series of videos. Thank you! I, for one, am looking forward to this "big job" you have lined up for that machine. Stay safe, regards from Canada's banana belt. 🤞🇨🇦🍌🥋🕊️🇺🇦🕊️🇺🇲🏁👍